Emerson COOL MATE XLH260 User manual

dIXEL
dIXELdIXEL
dIXEL
Operating instructions cod. 1592
cod. 1592cod. 1592
cod. 1592017400
017400017400
017400
1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 1/15
Temperature and Humidity controller
XLH260
XLH260XLH260
XLH260
C
CC
COOL
OOL OOL
OOL M
MM
MATE
ATEATE
ATE
Operating instructions

dIXEL
dIXELdIXEL
dIXEL
Operating instructions cod. 1592
cod. 1592cod. 1592
cod. 1592017400
017400017400
017400
1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 2/15
C
CC
COOL
OOLOOL
OOLM
MM
MATE
ATE ATE
ATE
XLH260
XLH260XLH260
XLH260
INDICE
1. GENERAL WARNINGS_________________________________________________________ 3
2. GENERAL DESCRI TION ______________________________________________________ 3
3. TEM ERATURE REGULATION __________________________________________________ 3
4. HUMIDITY REGULATION_______________________________________________________ 3
5. FA NS ______________________________________________________________________ 4
6. THE DIS LAY ________________________________________________________________ 5
7. ARAMETER LIST ____________________________________________________________ 7
8. DIGITAL IN UT_______________________________________________________________ 9
9. INSTALLATION AND MOUNTING _______________________________________________ 10
10. DIMENSIONS _______________________________________________________________ 12
11. ELECTRICAL CONNECTIONS__________________________________________________ 12
12. HOW TO USE THE HOT KEY __________________________________________________ 12
13. ALARM SIGNALLING _________________________________________________________ 13
10. TECHNICAL DATA ___________________________________________________________ 13
14. XLH260 CONNECTIONS ______________________________________________________ 14
15. DEFAULT SETTING VALUES __________________________________________________ 14

dIXEL
dIXELdIXEL
dIXEL
Operating instructions cod. 1592
cod. 1592cod. 1592
cod. 1592017400
017400017400
017400
1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 3/15
1. GENERAL WARNINGS
1.1 PLEASE READ BEFORE USING THIS MANUAL
•This manual is part of the product and should be kept near the instrument for easy and quick reference.
•The instrument shall not be used for purposes different from those described hereunder. It cannot be used as a safety device.
•Check the application limits before proceeding.
1.2 SAFETY PRECAUTIONS
•Check the supply voltage is correct before connecting the instrument.
•Do not expose to water or moisture: use the controller only within the operating limits avoiding sudden temperature changes with high
atmospheric humidity to prevent formation of condensation
•Warning: disconnect all electrical connections before any kind of maintenance.
•Fit the probe where it is not accessible by the End User. The instrument must not be opened.
•In case of failure or faulty operation send the instrument back to the distributor or to “Dixell s.r.l.” (see address) with a detailed description of the
fault.
•Consider the maximum current which can be applied to each relay (see Technical Data).
•Ensure that the wires for probes, loads and the power supply are separated and far enough from each other, without crossing or intertwining.
•In case of applications in industrial environments, the use of mains filters (our mod. FT1) in parallel with inductive loads could be useful.
2. GENERAL DESCRIPTION
The XLH260 is microprocessor controller, suitable for applications on medium or low temperature refrigerating units. It control both humidity and
temperature. It has 6 output relays to control compressor, heating elements, defrost, fan de-humidifier and humidifier. It has 2 NTC inputs one for
thermostat the other one for defrost. It’s also present an 4÷20mA input for humidity. There is one digital input (free contact) configurable by
parameter. An output allows the user to program the parameter list with the “Hot K y”.
3. TEMPERATURE REGULATION
The temperature regulation is performed through n utral zon using compressor and heater output relays.
Set point
OFF
ON
• H ating output: CUT IN is “SET TEM - dbt”, CUT OUT is when the temperature reaches the set point.
• Compr ssor output: CUT IN is “ SET TEM + dbt”, CUT OUT is when the temperature reaches the set point.
3.1 DEFROST
Two defrost modes are available through the “tdF” parameter: defrost with electrical heater or hot gas. The defrost interval is controlled by means of
parameter “EdF”: (EdF=in) the defrost is made every “IdF” time, (EdF=Sd) the interval “IdF” is calculate through Smart Defrost algorithm (only when
the compressor is ON). To disabl the defrost set the MdF parameter to z ro
Humidity regulation during a defrost depends on the Hud parameter. With Hud=no humidity regulation is disabled. With Hud=yES humidity
regulation is performed also during a defrost.
4. HUMIDITY REGULATION
The humidity regulation is performed through neutral zone, by humidifying dehumidifying actions. Humidity control can be disabled setting the SET
%RH to “nu” value. In this case only the temperature control is perform.
4.1 HUMIDIFYING ACTION
The humidifying action is done enabling the humidifier relay when the humidity is lower than the “SET %RH-dbH” value. The relay is switch off when
humidity reaches the set values.
4.2 DEHUMIDIFYING ACTION WITHOUT DEHUMIDIFIER RELAY (OA1 DIFFERENT FROM DEH) – STANDARD CONFIGURATION
In this case the dehumidifying action is performed by setting the following parameters in this way:
tHu = cH kind of d humidifying by m ans of h ating and compr ssor r lays
oA1 diff r nt from dEH:

dIXEL
dIXELdIXEL
dIXEL
Operating instructions cod. 1592
cod. 1592cod. 1592
cod. 1592017400
017400017400
017400
1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 4/15
The heating and compressor outputs are activated together when humidity is higher than SET %RH+dbH value. Outputs are disabled when humidity
comes back to the SET %RH value.
4.2.1 Relation between cooling, heating and dehumidifying
1. If is simultaneously present a request of cooling (temp>SET TEM +dbt) and dehumidifying (RH > SET %RH+dbH): the cooling action has the
priority over the dehumidifying action: only the compressor relay is energised till the SET TEM is reached at this point also the heating relay
is enabled.
2. If is simultaneously present a request of heating (temp< SET TEM -dbt) and dehumidifying (RH > SET %RH+dbH): the dehumidifying action
has the priority over the heating action: both the compressor and the heating relays are energised till the humidity set is reached at this point
only the heating relay is enabled.
4.3 DEHUMIDIFYING ACTION WITH DEHUMIDIFIER RELAY (OA1 = DEH)
The configurable relay is used, setting the parameter oA1 =dEH.
NOTE: the LIGHT button is not more available;
Two kinds of de-humidifying are available:
4.3.1 Dehumidifying action with ONLY de-humidifier relay
By setting the parameter tHu = db the de-humidifying action is performed by enabling the de-humidifier relay when the humidity is higher than SET
%RH + dbH.
The relay is switch off when humidity comes back to the SET %RH value.
4.3.2 Dehumidifying action with de-humidifier and compressor relays
By setting the parameter tHu = cHu the de-humidifying action is performed by enabling the de-humidifier and compressor relays together. when the
humidity is higher than SET %RH + dbH.
The relays are switched off when humidity comes back to the SET %RH value.
If is simultaneously present a request of cooling (temp>SET TEM +dbt) and dehumidifying (RH > SET %RH+dbH): the cooling action has the priority
over the dehumidifying action: only the compressor relay is energised till the SET TEM is reached at this point also the de-humidifier is enabled.
5. FA NS
The fan control mode is selected by means of the “FnC” parameter:
FnC=C-n fans will switch ON and OFF with the compressor and not run during defrost:;
FnC= O-n fans will run continuously, but not during defrost
FnC=C-y fans will switch ON and OFF with the compressor and run during defrost;
FnC=O-y fans will run continuously also during defrost

dIXEL
dIXELdIXEL
dIXEL
Operating instructions cod. 1592
cod. 1592cod. 1592
cod. 1592017400
017400017400
017400
1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 5/15
6. THE DISPLAY
C
F
SET SET
%RH
To display and modify target temperature set point. (SET TEM )
To display and modify target humidity set point (SET %RH); in programming mode it selects a parameter or confirm an operation.
In programming mode it browses the parameter codes or increases the displayed value.
To start a manual defrost: hold it pressed for at least 3s.
In programming mode it browses the parameter codes or decreases the displayed value.
Switch ON and OFF the light, if present (oA1=lig)
Switch ON and OFF the instrument.
KEY COMBINATIONS
+ To lock and unlock the keyboard
+ To enter the programming mode.
+ To exit the programming mode.
6.1 ICONS AND SYMBOLS
Each LED function is described in the following table.
LED MODE FUNCTION
ON - Instrument in stand by.
- In “ r2” indicates that the parameter is also present in “ r1”.
°C ON °C
°C FLASHING If measurement unit is °C, it flashing on programming mode
°F ON °F
°F FLASHING If measurement unit is °F, it flashing on programming mode

dIXEL
dIXELdIXEL
dIXEL
Operating instructions cod. 1592
cod. 1592cod. 1592
cod. 1592017400
017400017400
017400
1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 6/15
LED MODE FUNCTION
ON The compressor is running
FLASHING Anti-short cycle delay enabled
ON The defrost is enabled
FLASHING Drip time in progress
ON Heating enabled
(temp) FLASHING Temperature Set programming phase
ON ALARM signal
ON Fan is running
ON The light is on
ON RH%
ON Dehumidifying enabled
ON Humidifying enabled
(umid) FLASHING Humidity Set programming phase
6.2 HOW TO SEE AND MODIFY THE SET POINT (TEMPERATURE AND HUMIDITY)
OR
1. ush and immediately release the SET key: the display will show the Set point value and the correspondent set icon starts
flashing;
2. To change the Set value push the o
o o
o or n
nn
n arrows within 10s.
3. To memorise the new set point value push the SET key again or wait 10s.
6.3 TO START A MANUAL DEFROST
1. ush the DOWN key for more than 2 seconds and a manual defrost will start.
6.4 TO ENTER IN PARAMETERS LIST “PR1”
To enter the parameter list “ r1” (user accessible parameters) operate as follows:
+
1. Enter the rogramming mode by pressing the SET %RH+ n
n n
n for few seconds. (°C or °F icon start flashing)
2. The instrument will show the first parameter present in “ r1”
6.5 TO ENTER IN PARAMETERS LIST “PR2”
To access parameters in “Pr2”:
1. Enter the “ r1” level.
2. Select “ r2” parameter and press the “ SET %RH ” key.
3. The “ AS” flashing message is displayed, shortly followed by “0 - -” with a flashing zero.
4. Use o
oo
o or n
nn
n to input the security code in the flashing digit; confirm the figure by pressing “ SET %RH ”.
Th s curity cod is “321“.
5. If the security code is correct the access to “ r2” is enabled by pressing “ SET %RH ” on the last digit.
Anoth r possibility is the following: after switching ON the instrument the user can push SET %RH + n
nn
n keys within 30 seconds.
NOTE: each parameter in “ r2” can be removed or put into “ r1” (user level) by pressing SET %RH + n
nn
n. When a parameter is present in “ r1”
icon is on.
6.6 TO CHANGE PARAMETER VALUES
1. Enter the rogramming mode.
2. Select the required parameter with o
oo
o or n
nn
n.
3. ress the “ SET %RH ” key to display its value (°C or °F icon start blinking).
4. Use o
oo
o or n
nn
n to change its value.
5. ress “ SET %RH ” to store the new value and move to the following parameter.
To xit: ress SET %RH + UP or wait 15s without pressing a key.

dIXEL
dIXELdIXEL
dIXEL
Operating instructions cod. 1592
cod. 1592cod. 1592
cod. 1592017400
017400017400
017400
1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 7/15
NOTE: the new programming is stored even when the procedure is exited by waiting the time-out.
6.7 HOW TO LOCK THE KEYBOARD
AND
1. Keep the o
oo
o and n
nn
n keys pressed together for more than 3 s the o
oo
o and n
nn
n keys.
2. The “POF” message will be displayed and the keyboard is locked. At this point it is only possible the viewing of the set point or the
MAX o Min temperature stored and to switch ON and OFF the light, the auxiliary output and the instrument.
TO UNLOCK THE KEYBOARD
Keep the o
oo
o and n
nn
n keys pressed together for more than 3s.
6.8 ON/OFF FUNCTION
By pushing the ON/OFF key, the instrument shows “OFF” for 5 sec. and the ON/OFF LED is switched ON.
During the OFF status, all the relays are switched OFF and the regulations are stopped;
N.B. During th OFF status th icon is light d.
7. PARAMETER LIST
REGULATION
dbt half d ad band width for t mp ratur : (0,1÷25,5°C; 1÷45°F) this band is place below and above the temperature set point (SET TEM ).
The compressor is enabled when the temperature increases and reaches the SET TEM + dbt value. It is turned off when it comes back to
the SET TEM . The heating output is enabled when temperature is less than SET TEM -dbt value and disabled when the SET TEM is
reached.
dbH half d ad band width for humidity: (0,5÷25,5RH) this band is place below and above the humidity set point (SET %RH). The
dehumidifying action is enabled when the humidity increases and reaches the SET %RH + dbH value. It is stopped when it comes back to
the SET %RH. The humidifying output is enabled when humidity is less than SET %RH -dbH value and disabled when the SET %RH is
reached.
LS Minimum t mp ratur s t point limit: (-50,0°C÷
÷÷
÷SET; -58°F÷SET) Sets the minimum acceptable value for the set point.
US Maximum t mp ratur s t point limit: (SET÷
÷÷
÷110°C; SET÷230°F) Set the maximum acceptable value for set point.
OdS Outputs activation d lay at start up: (0÷255 min) This function is enabled at the initial start up of the instrument and inhibits any output
activation for the period of time set in the parameter. (Light can work)
AC Anti-short cycl d lay: (0÷30 min) interval between the compressor stop and the following restart.
tHu Kind of d -humidifying: db: only with de-humidifier relay (oA1= dEH); cHu with de-humidifier and compressor relay (oA1= dEH); c-H:
without de-humidifier relay, by means of compressor and heating relays (oA1≠ dEH).
LSH Minimum humidity s t point limit: (Lci ÷ Set H) Sets the minimum acceptable value for the humidity set point.
USH Maximum humidity s t point limit: (Set H ÷ uci) Set the maximum acceptable value for humidity set point.
DISPLAY
CF M asur m nt unit: °C= Celsius; °F= Fahrenheit
rES R solution (for °C): allows decimal point display. dE = 0,1°C; in = 1 °C
rEH R solution for RH%: in = integer; Hd= half digit.
DEFROST
tdF D frost typ : rE = electrical heater (Compressor OFF); in = hot gas (Compressor and defrost relays ON)
EdF D frost mod : in = int rval mod . The defrost starts when the time “Idf” is expired. Sd =Smartfrost mod . The time IdF (interval
between defrosts) is increased only when the compressor is running (even non consecutively).
SdF S t point for SMARTFROST: (-30÷30 °C/ -22÷86 °F) evaporator temperature which allows the IdF counting (interval between defrosts) in
SMARTFROST mode.
dtE D frost t rmination t mp ratur : (-50,0÷110,0°C; -58÷230°F) (Enabled only when the evaporator probe is present) sets the temperature
measured by the evaporator probe which causes the end of defrost.
IdF Int rval b tw n d frosts: (1÷120h) Determines the time interval between the beginning of two defrost cycles.
MdF Duration of d frost: (0÷255 min) When P2P = n, no evaporator probe, it sets the defrost duration, when P2P = y, defrost end based on
temperature, it sets the maximum length for defrost.
dFd Display during d frost: rt = real temperature; it = temperature reading at the defrost start; S t = set point; dEF = “dEF” label; dEG =
“dEG” label;
dAd D frost display tim out: (0÷255 min) Sets the maximum time between the end of defrost and the restarting of the real room temperature
display.
Fdt Drain down tim : (0÷60 min.) time interval between reaching defrost termination temperature and the restoring of the control’s normal
operation. This time allows the evaporator to eliminate water drops that might have formed due to defrost.
dPO First d frost aft r start-up: y = Immediately; n = after the IdF time
Hud Humidity control during d frost: no: the humidity control is stopped during the defrost; yES the humidity control works also during the
defrost.
FANS

dIXEL
dIXELdIXEL
dIXEL
Operating instructions cod. 1592
cod. 1592cod. 1592
cod. 1592017400
017400017400
017400
1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 8/15
FnC Fan op rating mod : C-n = running when a load is on, OFF during the defrost; C-y = running when a load is on, ON during the defrost; O-n
= continuous mode, OFF during the defrost; O-y = continuous mode, ON during the defrost;
TEMPERATURE ALARMS
ALC T mp ratur alarm configuration: rE = High and Low alarms related to Set oint; Ab = High and low alarms related to the absolute
temperature.
ALL Low t mp ratur alarm s tting: ALC = rE , 0 ÷
÷÷
÷ 50 °C or 90°F
ALC = Ab , - 50°C or -58°F ÷
÷÷
÷ ALU
when this temperature is reached and after the ALd delay time, the LA alarm is enabled,.
ALU High t mp ratur alarm s tting: ALC= rE, 0 ÷
÷÷
÷ 50°C or 90°F
ALC= Ab, ALL ÷ 110°C or 230°F
when this temperature is reached and after the ALd delay time the HA alarm is enabled.
ALH T mp ratur alarm r cov ry diff r ntial: (0,1÷25,5°C; 1÷45°F) Intervention differential for recovery of temperature alarm.
ALd T mp ratur alarm d lay: (0÷255 min) time interval between the detection of an alarm condition and the corresponding alarm signalling.
dAO D lay of t mp ratur alarm at start-up: (0min÷23h 50min) time interval between the detection of the temperature alarm condition after the
instrument power on and the alarm signalling.
EdA Alarm d lay at th nd of d frost: (0÷255 min) Time interval between the detection of the temperature alarm condition at the end of defrost
and the alarm signalling.
dot D lay of t mp ratur alarm aft r closing th door : (0÷255 min) Time delay to signal the temperature alarm condition after closing the
door.
HUMIDITY ALARMS
AHC Humidity alarm configuration: rE = High and Low alarms related to humidity Set oint; Ab = High and low alarms related to the “absolute”
humidity.
AHL Low humidity alarm s tting: (with AHC = rE: 0 ÷ 50. With AHC = Ab: Lci ÷ AHu)
when this humidity is reached and after the AHd delay time, the HLA alarm is enabled,.
AHu High humidity alarm s tting: (with AHC = rE: 0÷50°C. with AHC = Ab: AHL ÷ uci
when this humidity is reached and after the AHd delay time the HHA alarm is enabled.
AHH Humidity alarm r cov ry diff r ntial: (0.5÷20.0) Intervention differential for recovery of humidity alarm.
AHd Humidity alarm d lay: (0÷255 min) time interval between the detection of an alarm condition and the corresponding alarm signalling.
dHo D lay of humidity alarm at start-up: (0min÷23h 50min) time interval between the detection of the humidity alarm condition after the
instrument power on and the alarm signalling.
doH Alarm d lay at th nd of d frost: (0÷255 min) Time interval between the detection of the humidity alarm condition at the end of defrost
and the alarm signalling.
doA Op n door alarm d lay:(0÷255 min) delay between the detection of the open door condition and its alarm signalling: the flashing message
“dA” is displayed.
nPS Pr ssur switch numb r: (0 ÷15) Number of activation of the pressure switch, during the “did” interval, before signalling the alarm event
(I2F= AL). If th nPS activation in th “did” tim is r ach d, switch off and on th instrum nt to r start normal r gulation.
PROBE INPUTS
Ot Th rmostat prob calibration: (-12.0÷
÷÷
÷12.0°C/ -21÷
÷÷
÷21°F) allows to adjust possible offset of the thermostat probe.
OE Evaporator prob calibration: (-12.0÷
÷÷
÷12.0°C/ -21÷
÷÷
÷21°F) allows to adjust possible offsets of the evaporator probe.
O3 Humidity prob calibration: (-10÷
÷÷
÷10 RH) allows to adjust possible offsets of the humidity probe.
P2P Evaporator prob pr s nc : n= not present: the defrost stops only by time; y= present: the defrost stops by temperature and time.
P3P Humidity prob pr s nc : n= not present; y= present.
LCI R adout with 4 mA : (-999 ÷ 999). Adjustment of read out corresponding to 4mA signal.
UCI R adout with 20 mA : (-999 ÷ 999). Adjustment of read out corresponding to 20mA signal.
DIGITAL INPUTS
i1P Configurabl digital input polarity: CL : the digital input is activated by closing the contact; OP : the digital input is activated by opening
the contact;
i2P Door switch digital input polarity: CL : the digital input is activated by closing the contact; OP : the digital input is activated by opening the
contact;
i1F Digital input op rating mod : configure the digital input function: EAL = generic alarm; bAL = serious alarm mode; PAL = ressure
switch; Ht = heating relay safety; dor = door switch
odc Outputs status wh n op n door: on = normal; Fan = Fan OFF; oFF = all the loads off
rrd Outputs r starting aft r doA alarm: no = outputs not affected by the doA alarm; yES = outputs restart with the doA alarm;
did Tim int rval/d lay for digital input alarm:(0÷255 min.) Time interval to calculate the number of the pressure switch activation when
I1F= AL. If I1F=EAL or bAL (external alarms), “did” parameter defines the time delay between the detection and the successive signalling of
alarms.
OTHER
oA1 Light r lay configuration: ALr = alarm; dEH = dehumidifier; onF = on/off relay: close with instrument on, open with instrument off; Lig =
light, ESt, dEF not s l ct

dIXEL
dIXELdIXEL
dIXEL
Operating instructions cod. 1592
cod. 1592cod. 1592
cod. 1592017400
017400017400
017400
1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 9/15
Adt RS485 s rial addr ss, t mp ratur s ction (0÷247) it identifies the temperature section of the instrument within a control or supervising
system.
NOTE: XJ500: set Adt different from AdH. X-WEB300/3000: set Adt equal to AdH.
AdH RS485 s rial addr ss, humidity s ction (0÷247) it identifies the humidity section of the instrument within a control or supervising system.
Ptb Param t r tabl : (read only) it shows the original code of the dIXEL parameter map.
rEL Softwar r l as : (read only) Software version of the microprocessor.
Prd Prob s display: (read only) display the temperature values of the evaporator probe b2.
Pr2 Acc ss to th prot ct d param t r list (read only).
8. DIGITAL INPUT
One digital input is present configurable by user by means of the i1F parameter according to the following descriptions.
8.1 DIGITAL INPUT 1 (5-6): DOOR SWITCH
It signals the door status and the corresponding relay output status through the “odc” parameter: no = normal (any change); Fan = Fan OFF; oFF =
all the loads are switched off.
Since the door is opened, after the delay time set through parameter “dOA”, the alarm output is enabled and the display shows the message “dA”.
The status of loads depends on the “rrd” parameter:
with rrd=no outputs are not affected by the doA alarm;
with rrd=yES = outputs restart with the doA alarm;
The alarm stops as soon as the external digital input is disabled again. During this time and then for the delay “dot” and “doH” after closing the door,
the temperature and humidity alarms are disabled.
8.2 DIGITAL INPUT 2 (3-4): GENERIC ALARM (I1F = EAL)
As soon as the digital input is activated the unit will wait for “did” time delay before signalling the “EAL” alarm message. The outputs status don’t
change. The alarm stops just after the digital input is de-activated.
8.3 DIGITAL INPUT 2 (3-4): SERIOUS ALARM MODE (I1F = BAL)
When the digital input is activated, the unit will wait for “did” delay before signalling the “bAL” alarm message. The relay outputs are switched OFF.
The alarm will stop as soon as the digital input is de-activated.
8.4 DIGITAL INPUT 2 (3-4): PRESSURE SWITCH (I1F = PAL)
If during the interval time set by “did” parameter, the pressure switch has reached the number of activation of the “nPS” parameter, the “PAL”
pressure alarm message will be displayed. The compressor and the regulation are stopped. When the digital input is ON the compressor is always
OFF. If th nPS activation in th did tim is r ach d, switch off and on th instrum nt to r start normal r gulation.
8.5 DIGITAL INPUT 2 (3-4): HEATING RELAY SAFETY (i1F=Ht)
With i1F=Ht as soon as the digital input is activated for “did” time heating relay is disabled. The alarm will stop as soon as the digital input is de-
activated.
8.6 DIGITAL INPUTS POLARITY
The digital input polarity depends on the “i1P” and “i2P”parameters. CL : the digital input is activated by closing the contact. OP : the digital input is
activated by opening the contact

dIXEL
dIXELdIXEL
dIXEL
Operating instructions cod. 1592
cod. 1592cod. 1592
cod. 1592017400
017400017400
017400
1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 10/15
9. INSTALLATION AND MOUNTING
The temperature range allowed for correct operation is 0 - 60 °C. Avoid places subject to strong vibrations, corrosive gases, excessive dirt or
humidity. The same recommendations apply to probes. Let the air circulate by the cooling holes. Thanks to the case, XLH260 model can be panel or
wall mounted. See the following instructions for details.
A B
C
D
E
G
F
FIG. 1
A
B
C
G
F
D
FIG. 2
87
230
MAX 37
210
130
120
M
A
X
2
8
H
I
FIG. 3

dIXEL
dIXELdIXEL
dIXEL
Operating instructions cod. 1592
cod. 1592cod. 1592
cod. 1592017400
017400017400
017400
1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 11/15
A
Fig. 6
2
0
0
6
1
0
0
172
106.44°
190
18
Fig. 4
2
0
0
1
9
2
.
5
1
8
5
61
12
6
0
0
4
11
14.5
22.5
29.5
160.55
167.5
175.5
179
186
190
R
5
8.5
8
.
5
1
0
6
.
4
4
°
R
5
Fig. 5
9.1 WALL MOUNTING
1. Unscrew the 4 frontal screws (Fig. 1, A, B, F, G) and remove the cover (Fig. 1, C).
2. Unscrew the 2 screws (Fig. 1, D, E) that keep connected the frontal and lower parts of Cool Mate and separate the 2 parts.
3. Make the proper holes for cablepresses or pipepresses using the centres signed in the bottom cover of the Cool Mate, (Fig. 3, H, I, ). Then
make 3 holes in the wall, as indicated in (Fig. 3, L, M, N), to fix the Cool Mate
4. Fix the cablepresses and the pipepresses..
5. Insert the wall-nugs, contained in the kit, into the holes made in the wall. Then use the o-rings and fix the back part of the Cool Mate (Fig. 3, L,
M, N) by means of the 3 screws to the wall itself.
6. Insert the wiring cables in cablepresses or in the pipepresses.
7. Mount the frontal part using the previous 4 screws Fig. 1, D, E, F, G. (do not press excessively in order to avoid plastic deformation).
8. After connecting the wires to the terminal blocks close the cover (Fig. 2, c) and fix it by the screws.
9.2 PANEL MOUNTING
1. Make a hole in the panel with dimensions described in Fig. 4 (simplified) or Fig. 5 (completed)
2. Unscrew the 4 frontal screws (Fig. 1, A, B, F, G) and remove the cover (Fig. 1, C).

dIXEL
dIXELdIXEL
dIXEL
Operating instructions cod. 1592
cod. 1592cod. 1592
cod. 1592017400
017400017400
017400
1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 12/15
3. Unscrew the 2 screws (Fig. 1, D, E) that keep connected the frontal and lower parts of Cool Mate and separate the 2 parts.
4. Cut from the back part of the Cool Mate the teeth indicated in Fig. 6, A.
5. Make the proper holes for cablepresses or pipepresses using the centres signed in the bottom cover of the Cool Mate, (Fig. 3, H, I, ).
6. Fix the cablepresses and the pipepresses..
7. Insert the wiring cables in cablepresses or in the pipepresses.
8. Join the back and frontal parts, with the panel in the middle, and fix them screwing the 4 screws taken previously away (dimensions 4x35
mm), in the holes of Fig. 1, A, B, D, E. Maximum panel thickness: 6mm.
9. After connecting the wires to the terminal blocks close the cover (Fig. 2, c) and fix it by the screws.
10. DIMENSIONS
210
87
2
3
0
11. ELECTRICAL CONNECTIONS
The instruments are provided with screw terminal block to connect cables with a cross section up to 2,5 mm2. Heat-resistant cables have to be used.
Before connecting cables make sure the power supply complies with the instrument’s requirements. Separate the probe cables from the power
supply cables, from the outputs and the power connections. Do not exceed the maximum current allowed on each relay, in case of heavier loads use
a suitable external relay.
11.1 PROBE CONNECTIONS
The probes shall be mounted with the bulb upwards to prevent damages due to casual liquid infiltration. It is recommended to place the thermostat
probe away from air streams to correctly measure the average room temperature.
12. HOW TO USE THE HOT KEY
12.1 HOW TO PROGRAM A HOT KEY FROM THE INSTRUMENT (UPLOAD)
1. rogram one controller with the front keypad.
2. When the controller is ON, insert the “Hot k y” and push o
oo
o key; the "uPL" message appears followed a by flashing “End”
3. ush “SET” key and the End will stop flashing.
4. Turn OFF the instrument remove the “Hot K y”, then turn it ON again.
NOTE: the “Err” message is displayed for failed programming. In this case push again o
oo
o key if you want to restart the upload again or remove the
“Hot k y” to abort the operation.
12.2 HOW TO PROGRAM AN INSTRUMENT USING A HOT KEY (DOWNLOAD)
1. Turn OFF the instrument.
2. Insert a programm d “Hot K y” into th 5 PIN r c ptacl and then turn the Controller ON.
3. Automatically the parameter list of the “Hot K y” is downloaded into the Controller memory, the “doL” message is blinking followed a by
flashing “End”.
4. After 10 seconds the instrument will restart working with the new parameters.
5. Remove the “Hot K y”..
NOTE the message “Err” is displayed for failed programming. In this case turn the unit off and then on if you want to restart the download again or
remove the “Hot k y” to abort the operation.

dIXEL
dIXELdIXEL
dIXEL
Operating instructions cod. 1592
cod. 1592cod. 1592
cod. 1592017400
017400017400
017400
1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 13/15
13. ALARM SIGNALLING
M ssag
Caus Outputs
“ 1” Thermostat probe failure Compressor and heating outputs off
“ 2” Evaporator probe failure Defrost and by time
“ 3” Humidity probe failure Humidity regulation off
“HA” High temperature alarm Outputs unchanged
“LA” Low temperature alarm Outputs unchanged
“HHA” High humidity alarm Outputs unchanged
“HLA” Low humidity alarm Outputs unchanged
“dA” Door switch alarm Outputs depending on the odC parameter
“EAL” External alarm Other outputs unchanged
“BAL” Serious external alarm Outputs OFF
“ AL” ressure switch alarm Outputs OFF
The alarm message is displayed until the alarm condition recoveries.
All the alarm messages are showed alternating with the room temperature except for the “P1” which is flashing. To reset the “EE” alarm and restart
the normal functioning press any key, the “rSt” message is displayed for about 3s.
13.1 SILENCING BUZZER
Once the alarm signal is detected the buzzer, if present, can be silenced by pressing any key.
13.2 ALARM RECOVERY
Prob alarms : “P1” (probe1 faulty), “P2”, “P3”; they automatically stop 10s after the probe restarts normal operation. Check connections before
replacing the probe.
T mp ratur alarms “HA” and “LA” automatically stop as soon as the thermostat temperature returns to normal values or when the defrost starts.
Humidity alarms “HHA” and “LHA” automatically stop as soon as the humidity returns to normal values.
Door switch alarm “dA” stop as soon as the door is closed.
Ext rnal alarms “EAL”, “BAL” stop as soon as the external digital input is disabled
Pr ssur switch alarm “PAL” alarm is r cov r d by switching OFF th instrum nt.
10. TECHNICAL DATA
Housing: self extinguishing ABS; Cas : frontal 210x230 mm; depth 87mm; Mounting: See par. 9; Prot ction: I 65
Conn ctions: Screw terminal block ≤ 2,5 mm2 wiring.
Pow r supply: 230Vac 50/60Hz ± 10% or 110Vac 50/60Hz ± 10%; Pow r absorption: 10VA max.
Display:3 digits, red LED, 30.5 mm high; 3 digits, yellow LED low.
Inputs: 2 NTC probes, one 4÷20mA input
Digital inputs : door switch and configurable, free voltage. Max. distance 10m
R lay outputs:
compr ssor: relay S ST 20(8) A, 250Vac;
d frost: relay S DT 16(3) A, 250Vac;
fans: relay S ST 8(3) A, 250Vac;
h at r control: relay S ST 20(8) A, 250Vac;
Humidifying: relay S ST 8(3) A, 250Vac;
D humidifying / Light: relay S ST 16(3) A, 250Vac
Oth r output :
Alarm buzz r (Standard)
Dir ct RS485 (optional)
Data storing: on the non-volatile memory (EE ROM).
Kind of action: 1B.; Pollution grad : normal; Softwar class: A.
Op rating t mp ratur : 0÷60 °C.; Storag t mp ratur : -25÷60 °C.
R lativ humidity: 20÷85% (no condensing)
M asuring and r gulation rang : NTC prob : -40÷110°C (-58÷230°F);
R solution: 0,1 °C or 1°C or 1 °F (selectable).
Accuracy (ambi nt t mp. 25°C): ±0,5 °C ±1 digit

dIXEL
dIXELdIXEL
dIXEL
Operating instructions cod. 1592
cod. 1592cod. 1592
cod. 1592017400
017400017400
017400
1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 14/15
14. XLH260 CONNECTIONS
1 2 3 4 5 6 7 8 9 101 1 12 13 14 151 6 17 18 19 20 21 222 3 24 25 26 2728 29 30 31 33 34
Conf. Do or
Room
Evap.
HO T KEY
16A
250V~16A 250V~8 A 250V~
20A 250V
16 FLA (96L RA)
20A 250V
16FLA(96L RA)
8A
250V ~
Supply
120/230V~
NLin
NC
Fa n
35 36
In
12V§gnd
Input
4÷20mA
Hea ter Hum
L ight De-
Hum
Comp Def
NC
RS 485
(optionaal)
15. DEFAULT SETTING VALUES
Lab l Valu M nu D scription Rang
S t T 5.0 - - - Temperature Set oint LS ÷ uS ( nu = temperature regulation disabled )
S t H 50.0 - - - Humidity Set oint LSH ÷ uSH ( nu = humidity regulation disabled)
dbt 2.0 r1 Half dead band width for temperature 0.1°C o 1°F ÷ 25°C o 77°F
dbH 5.0 r1 Half dead band width for humidity 0.5 ÷ 50
LS -40 r2 Minimum temperature set point limit -50.0°C o –58°F ÷ Set T
uS 110 r2 Maximum temperature set point limit Set T ÷ 110°C o 230°F
odS 1 r2 Outputs activation delay at start up 0 ÷ 250 min
Ac 1 r1 Anti-short cycle delay 0 ÷ 30 min
tHu c-H r2 Humidity regulation db = dehumidifier relay.; cHu = dehum+ compr.; c-H= without
dehum. relay
LSH 0.0 r2 Minimum humidity set point limit Lci ÷ Set H
uSH 100.0 r2 Maximum humidity set point limit Set H ÷ uci
cF °C r2 Measurement unit °C ÷°F
rES dE r2 Resolution (for °C): in = integer / dE = decimal
rEH Hd r2 Resolution for RH%: in = integer / Hd = half digit
tdf rE r2 Defrost type rE, rT, in
EdF in r2 Defrost mode In, Sd
SdF 0 r2 Set point for SMART DEFROST -30 ÷ +30°C / -22÷+86°F
dtE 8 r2 Defrost termination temperature -50,0÷110°C/ -58÷230°F
idF 6 r1 Interval between defrosts 1 ÷ 120 h
MdF 20 r1 Duration of defrost 0 ÷ 250 min
dFd it r2 Display during defrost rt / it / SEt / dEF / dEG
dAd 30 r2 Defrost display time out 0 ÷ 250 min
Fdt 0 r2 Draining time 0÷60 min.
dPo no r2 First defrost after start up n ÷ y
Hud no r2 Humidity control during defrost no; yES
Fnc c-n r2 Fan operating mode c-n / c-Y / o-n / o-Y
ALc Ab r2 Temperature alarm configuration rE = relative / Ab = absolute
ALL -40.0 r1 Low temperature alarm setting 0°C ÷ 50.0°C / -50.0°C ÷ ALu
ALu 110 r1 High temperature alarm setting 0°C ÷ 50.0°C / ALL ÷ 110°C
ALH 1.0 r2 Temperature alarm recovery differential 0.1°C o 1°F ÷ 25°C o 77°F
ALd 15 r2 Temperature alarm delay 0 ÷ 250 min
dAo 1.3 r2 Delay of temperature alarm at start-up 0.0 ÷ 23.5 h
EdA 20 r2 Alarm delay at the end of defrost 0 ÷ 250 min
dot 20 r2
Delay of temperature alarm after closing the
door 0 ÷ 250 min
AHc Ab r2 Humidity alarm configuration rE = relative / Ab = absolute
AHL 0.0 r1 Low humidity alarm setting 0 ÷ 50 / Lci ÷ AHu
AHu 100 r1 High humidity alarm setting 0 ÷ 50 / AHL ÷ uci
AHH 2.0 r2 Humidity alarm recovery differential 0.5 ÷ 25
AHd 15 r2 Humidity alarm delay 0 ÷ 250 min
dHo 1.3 r2 Delay of humidity alarm at start-up 0.0 ÷ 23.5 h
doH 20 r2 Alarm delay at the end of defrost 0 ÷ 250 min
nPS 20 r2 ressure switch number 0÷15

dIXEL
dIXELdIXEL
dIXEL
Operating instructions cod. 1592
cod. 1592cod. 1592
cod. 1592017400
017400017400
017400
1592017400 XLH260 GB r1.0 15.04.2005.doc XLH260 15/15
doA 0 r2 Open door alarm delay 0 ÷ 250 min ( 250 = nu )
ot 0.0 r1 Thermostat probe calibration -12.0 ÷ 12.0
oE 0.0 r2 Evaporator probe calibration -12.0 ÷ 12.0
o3 0.0 r1 Humidity probe calibration -10 ÷ 10
P2P YES r2 Evaporator probe presence no = absent / YES = present
P3P YES r2 Humidity probe presence no = absent / YES = present
Lci 0 r2 Readout with 4 mA -999 ÷ 999
uci 100 r2 Readout with 20 mA -999 ÷ 999
i1P cL r2 Configurable digital input polarity cL =open / o = close
i2P cL r2 Door switch digital input polarity cL =open / o = close
i1F EAL r2 Digital input configuration dor / AL / EAL / bAL / Ht
odc FAn r2 Outputs status when open door on / Fan / oFF
rrd YES r2 Outputs restarting after doA alarm no = no / YES = yes
did 5 r2 Digital input alarm delay 0÷255 min.
oA1 Lig r2 Light relay configuration: ALr = alarm; dEH = dehumidifier; onF = on/off; Lig = light,
ESt, dEF not s l ct
Adr 1 r2 Serial address 0÷247 num
Ptb - r2 arameter table - - -
rEL 1.0 r2 Software release - - -
Prd -- r2 robes display b1÷ b3
Pr2 321 r1 Access to the protected parameter list - - -
dIXEL
dIXELdIXEL
dIXEL S.p.a.
Z.I. Via dell’Industria, 27 - 32010 ieve d’Alpago (BL) ITALY
tel. +39 - 0437 - 98 33 - fax +39 - 0437 - 98 93 13
http://www.dixell.com E-mail: [e-mail]