Emerson Rosemount 2090 Configuration guide

Manual Supplement
00809-0200-4108, Rev AB
December 2018
Rosemount™2090 Pressure Transmitter
Safety Instrumented Systems (SIS) Requirements
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1
SIS operation and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4
1.0 Overview
The safety-critical output of the Rosemount 2090 Pressure Transmitter is provided through a two-wire,
4–20 mA signal representing pressure. The Rosemount 2090 safety certified pressure transmitter is
certified to: Low Demand; Type B.
SIL 2 for random integrity @ HFT=0
SIL 3 for random integrity @ HFT=1
SIL 3 for systematic integrity
1.1 Rosemount 2090 safety certified identification
All Rosemount 2090 transmitters must be identified as safety certified before installing into SIS systems.
To identify a safety certified Rosemount 2090:
1. Check Namur Software Revision located on the metal device tag. “SW _._._”.
Namur Software Revision Number
SW(1) 1.0.x –1.4.x
1. NAMUR Software Revision: Located on the metal device tag
2. Verify that option code QT is included in the transmitter model code.
1.2 Installation in SIS applications
Installations are to be performed by qualified personnel. No special installation is required in addition to
the standard installation practices outlined in this document. Always ensure a proper seal by installing
the electronics housing cover(s) so that metal contacts metal.
Environmental and operational limits are available in “Specifications and Reference Data,” in the
Reference Manual.
The loop should be designed so the terminal voltage does not drop below 10.5 Vdc when the transmitter
output is set to 23 mA.

2
Manual Supplement
00809-0200-4108, Rev AB
Rosemount 2090 Pressure Transmitter
December 2018
Rosemount 2090 Pressure Transmitter
Position the security switch to the ( ) position to prevent accidental or deliberate change of
configuration data during normal operation.
1.3 Configuring in SIS applications
Use any HART capable configuration tool to communicate with and verify configuration of the
Rosemount 2090.
Note
Transmitter output is not safety-rated during the following: configuration changes, multidrop, and loop
test. Alternative means should be used to ensure process safety during transmitter configuration and
maintenance activities.
1.4 Damping
User-selected damping will affect the transmitters ability to respond to changes in the applied process.
The damping value + response time must not exceed the loop requirements. See the Reference Manual.
1.5 Alarm and saturation levels
DCS or safety logic solver should be configured to match transmitter configuration. Figure 1-1 identifies
the three alarm levels available and their operation values.
Figure 1-1. Alarm levels
1. Transmitter Failure, hardware or software alarm in LO position.
2. Transmitter Failure, hardware of software alarm in HI position.
Rosemount alarm level
Normal Operation
3.75 mA(1) 4 mA 20 mA 21.75(2)
3.9 mA
low saturation
20.8 mA
high saturation
Namur alarm level
Normal Operation
3.6 mA(1) 4 mA 20 mA 22.5(2)
3.8 mA
low saturation
20.5
high saturation
Custom alarm level
Normal Operation
3.6 - 3.8 mA(1) 4 mA 20 mA 20.2 - 23.0(2)
3.7 - 3.9 mA
low saturation
20.1 - 22.9 mA
high saturation

3
Manual Supplement
00809-0200-4108, Rev AB
Rosemount 2090 Pressure Transmitter
December 2018
Rosemount 2090 Pressure Transmitter
2.0 SIS operation and maintenance
2.1 Proof test
The following proof tests are recommended. In the event that an error is found in the safety and
functionality, proof test results and corrective actions taken can be documented at Emerson.com/Rose-
mount/SafetyWeb-Apps/Report-A-Failure.
All proof test procedures must be carried out by qualified personnel.
Use Field Communicator Menu Trees and Fast Keys to perform a Loop Test, Analog Output Trim, or
Sensor Trim. Security switch should be in the ( ) position during proof test execution and repositioned
in the ( ) position after execution. See Appendix D of the Reference Manual.
2.2 Partial proof test
The simple suggested proof test consists of a power cycle plus reasonability checks of the transmitter
output. Reference the FMEDA Report for percent of possible DU failures in the device.
FMEDA report can be found at: Emerson.com/Rosemount/Safety-Products.
Required tools: Field Communicator and mA meter.
1. Bypass the safety function and take appropriate action to avoid a false trip.
2. Use HART®Communications to retrieve any diagnostics and take appropriate action.
3. Send a HART command to the transmitter to go to the high alarm current output and verify that the
analog current reaches that value(1). See Verifying alarm level in the Reference Manual.
4. Send a HART command to the transmitter to go to the low alarm current output and verify that the
analog current reaches that value(1).
5. Remove the bypass and otherwise restore the normal operation.
6. Place the Security switch in the ( ) position.
2.3 Comprehensive proof test
The comprehensive proof test consists of performing the same steps as the simple suggested proof test
but with a two point calibration of the pressure sensor in place of the reasonability check. Reference the
FMEDA Report for percent of possible DU failures in the device.
Required tools: Field Communicator and pressure calibration equipment.

4
Manual Supplement
00809-0200-4108, Rev AB
Rosemount 2090 Pressure Transmitter
December 2018
Rosemount 2090 Pressure Transmitter
1. Bypass the safety function and take appropriate action to avoid a false trip.
2. Use HART communications to retrieve any diagnostics and take appropriate action.
3. Send a HART command to the transmitter to go to the high alarm current output and verify that the
analog current reaches that value(1). See Verifying alarm level, in the Reference Manual.
4. Send a HART command to the transmitter to go to the low alarm current output and verify that the
analog current reaches that value (2).
5. Perform a two-point calibration check of the sensor (see Section 5: Trim the pressure signal in the
Reference Manual) over the full working range and verify the current output at each point.
6. Remove the bypass and otherwise restore the normal operation.
7. Place the Security switch in the ( ) position.
1. This test for possible quiescent current related failures.
2. This tests for compliance voltage problems such as a low loop power supply voltage or increased wiring distance. This also tests for other possible failures.
Note
The user determines the proof test requirements for impulse piping.
Automatic diagnostics are defined for the corrected percent DU: The tests performed internally by
the device during runtime without requiring enabling or programming by the user.
2.4 Calculation of average probability of failure on demand (PFDAVG)
PFDAVG calculation can be found in the FMEDA report located at: Emerson.com/Rose-
mount/Safety-Products.
3.0 Inspection
3.1 Product repair
The Rosemount 2090 is not repairable and must be replaced in case of failure.
All failures detected by the transmitter diagnostics or by the proof-test must be reported. Feedback can
be submitted electronically at Emerson.com/Rosemount/SafetyWeb-Apps/Report-A-Failure.
All product repair and part replacement should be performed by qualified personnel.
3.2 Rosemount 2090 SIS reference
The Rosemount 2090must be operated in accordance to the functional and performance specifications
provided in Specifications and Reference Data in the Reference Manual.

5
Manual Supplement
00809-0200-4108, Rev AB
Rosemount 2090 Pressure Transmitter
December 2018
Rosemount 2090 Pressure Transmitter
3.3 Failure rate data
The FMEDA report includes failure rates and common cause Beta factor estimates. The report is available
at Emerson.com/Rosemount/Safety-Products.
3.4 Failure values
Transmitter response time: Reference Appendix A: specifications and reference data in the Reference
Manual.
Self-diagnostics test interval: At least once every 60 minutes
3.5 Product life
50 years - based on worst case component wear-out mechanisms - not based on wear-out of process
wetted materials
Report any safety related product information at: Emerson.com/Rosemount/Safety-
Web-Apps/Report-A-Failure

Manual Supplement
00809-0200-4108, Rev AB
December 2018
Global Headquarters
Emerson Automation Solutions
6021 Innovation Blvd.
Shakopee, MN 55379, USA
[phone] or [phone]
[phone]
[e-mail]
North America Regional Office
Emerson Automation Solutions
8200 Market Blvd.
Chanhassen, MN 55317, USA
[phone] or [phone]
[phone]
[e-mail]
Latin America Regional Office
Emerson Automation Solutions
1300 Concord Terrace, Suite 400
Sunrise, FL 33323, USA
[phone]
[phone]
[e-mail]
Europe Regional Office
Emerson Automation Solutions Europe GmbH
Neuhofstrasse 19a P.O. Box 1046
CH 6340 Baar
Switzerland
[phone]
[phone]
[e-mail]
Asia Pacific Regional Office
Emerson Automation Solutions
1 Pandan Crescent
Singapore 128461
[phone]
[phone]
[email protected]
Middle East and Africa Regional Office
Emerson Automation Solutions
Emerson FZE P.O. Box 17033
Jebel Ali Free Zone - South 2
Dubai, United Arab Emirates
[phone]
[phone]
[e-mail]
Linkedin.com/company/Emerson-Automation-Solutions
Twitter.com/Rosemount_News
Facebook.com/Rosemount
Youtube.com/user/RosemountMeasurement
Google.com/+RosemountMeasurement
Emerson Terms and Conditions of Sale are available upon request.
The Emerson logo is a trademark and service mark of Emerson Electric Co.
Rosemount and Rosemount logotype are trademarks of Emerson.
All other marks are the property of their respective owners.
©2018 Emerson. All rights reserved.