Endress+Hauser Memosens CLL47E User manual

Products Solutions Services
Operating Instructions
Memosens CLL47E
Contacting conductivity sensor for laboratory
measurements and random sampling in the field
Digital with Memosens 2.0 technology
BA02216C/07/EN/01.21-00
71558607
2021-11-30

Table of contents Memosens CLL47E
2 Endress+Hauser
Table of contents
1 About this document ........... 3
1.1 Warnings ........................... 3
1.2 Symbols ............................ 3
1.3 Documentation ...................... 3
2 Basic safety instructions ....... 4
2.1 Requirements for the personnel ........ 4
2.2 Intended use ........................ 4
2.3 Workplace safety .................... 4
2.4 Operational safety ................... 4
2.5 Product safety ....................... 5
3 Incoming acceptance and
product identification .......... 5
3.1 Incoming acceptance ................. 5
3.2 Product identification ................. 5
3.3 Scope of delivery ..................... 6
4 Electrical connection ........... 6
4.1 Connecting the sensor ................ 6
5 Commissioning ................. 7
6 Maintenance .................... 8
6.1 Cleaning the sensor .................. 8
6.2 Sensor calibration .................... 9
7 Repair ........................... 9
7.1 General information .................. 9
7.2 Return ............................. 9
7.3 Disposal ............................ 9
8 Accessories .................... 10
8.1 Device-specific accessories ............ 10
8.2 Communication-specific accessories ... 10
9 Technical data ................. 11
9.1 Input .............................. 11
9.2 Performance characteristics .......... 11
9.3 Environment ....................... 12
Index ................................. 13

Memosens CLL47E About this document
Endress+Hauser 3
1 About this document
1.1 Warnings
Structure of information Meaning
LDANGER
Causes (/consequences)
If necessary, Consequences of non-
compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid the dangerous situation will result in a fatal or serious injury.
LWARNING
Causes (/consequences)
If necessary, Consequences of non-
compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid the dangerous situation can result in a fatal or serious injury.
LCAUTION
Causes (/consequences)
If necessary, Consequences of non-
compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid this situation can result in minor or more serious injuries.
NOTICE
Cause/situation
If necessary, Consequences of non-
compliance (if applicable)
‣Action/note
This symbol alerts you to situations which may result in damage to property.
1.2 Symbols
Additional information, tips
Permitted or recommended
Not permitted or not recommended
Reference to device documentation
Reference to page
Reference to graphic
 Result of a step
1.3 Documentation
The following manuals, which complement these Operating Instructions, can be found on the
product pages on the Internet:
Technical Information Memosens CLL47E, TI01666C
Operating Instructions Liquiline Mobile CML18, BA02002C
Operating Instructions Memobase Plus CYZ71D, BA00502C

Basic safety instructions Memosens CLL47E
4 Endress+Hauser
2 Basic safety instructions
2.1 Requirements for the personnel
• Installation, commissioning, operation and maintenance of the measuring system may be
carried out only by specially trained technical personnel.
• The technical personnel must be authorized by the plant operator to carry out the specified
activities.
• The electrical connection may be performed only by an electrical technician.
• The technical personnel must have read and understood these Operating Instructions and
must follow the instructions contained therein.
• Faults at the measuring point may only be rectified by authorized and specially trained
personnel.
Repairs not described in the Operating Instructions provided must be carried out only
directly at the manufacturer's site or by the service organization.
2.2 Intended use
The Memosens CLL47E conductivity sensor is designed for the short-term measurement of
low to high conductivity of liquids in laboratory or field environments.
The Memosens CLL47E conductivity sensor is not intended for:
• Continuous measurements and fixed installation in the process or in assemblies
• Use in very corrosive media that can corrode stainless steel, for example.
Use of the device for any purpose other than that described, poses a threat to the safety of
people and of the entire measuring system and is therefore not permitted.
The manufacturer is not liable for damage caused by improper or non-designated use.
2.3 Workplace safety
As the user, you are responsible for complying with the following safety conditions:
• Installation guidelines
• Local standards and regulations
2.4 Operational safety
Before commissioning the entire measuring point:
1. Verify that all connections are correct.
2. Ensure that electrical cables and hose connections are undamaged.
3. Do not operate damaged products, and protect them against unintentional operation.
4. Label damaged products as defective.
During operation:
‣If faults cannot be rectified:
products must be taken out of service and protected against unintentional operation.

Memosens CLL47E Incoming acceptance and product identification
Endress+Hauser 5
2.5 Product safety
The product is designed to meet state-of-the-art safety requirements, has been tested, and
left the factory in a condition in which it is safe to operate. The relevant regulations and
international standards have been observed.
3 Incoming acceptance and product identification
3.1 Incoming acceptance
1. Verify that the packaging is undamaged.
 Notify the supplier of any damage to the packaging.
Keep the damaged packaging until the issue has been resolved.
2. Verify that the contents are undamaged.
 Notify the supplier of any damage to the delivery contents.
Keep the damaged goods until the issue has been resolved.
3. Check that the delivery is complete and nothing is missing.
 Compare the shipping documents with your order.
4. Pack the product for storage and transportation in such a way that it is protected
against impact and moisture.
 The original packaging offers the best protection.
Make sure to comply with the permitted ambient conditions.
If you have any questions, please contact your supplier or your local Sales Center.
3.2 Product identification
3.2.1 Nameplate
The nameplate provides you with the following information on your device:
• Manufacturer identification
• Extended order code
• Serial number
‣Compare the information on the nameplate with the order.
3.2.2 Product identification
Product page
www.endress.com/cll47e
Interpreting the order code
The order code and serial number of your product can be found in the following locations:
• On the nameplate
• In the delivery papers

Electrical connection Memosens CLL47E
6 Endress+Hauser
Obtaining information on the product
1. Go to www.endress.com.
2. Page search (magnifying glass symbol): Enter valid serial number.
3. Search (magnifying glass).
 The product structure is displayed in a popup window.
4. Click the product overview.
 A new window opens. Here you fill information pertaining to your device, including
the product documentation.
Manufacturer address
Endress+Hauser Conducta GmbH+Co. KG
Dieselstraße 24
D-70839 Gerlingen
3.3 Scope of delivery
The scope of delivery includes:
• Sensor in the version ordered
• Operating Instructions
4 Electrical connection
4.1 Connecting the sensor
4.1.1 Connection to handheld device
A0041682
 1 Sensor connection
1. Insert the sensor into the Memosens connection.
2. Turn the plug-in head of the sensor until it locks into place.

Memosens CLL47E Commissioning
Endress+Hauser 7
4.1.2 Connection to handheld device via M12 cable
1.
A0041681
Connect the M12 cable to the handheld device.
2.
A0041680
Insert the sensor into the Memosens connection of the M12 cable and lock into place.
5 Commissioning
1. For accurate, precise conductivity measurement:
Check the temperature compensation and damping settings on the transmitter.

Maintenance Memosens CLL47E
8 Endress+Hauser
2. For measurement, calibration and adjustment:
Follow the Operating Instructions for the transmitter.
Operating Instructions Liquiline Mobile CML18, BA02002C
6 Maintenance
6.1 Cleaning the sensor
LCAUTION
Corrosive chemicals
Risk of chemical burns to the eyes and skin and risk of damage to clothing and equipment!
‣It is absolutely essential to protect the eyes and hands properly when working with acids,
alkalis and organic solvents!
‣Wear protective goggles and safety gloves.
‣Clean away splashes on clothes and other objects to prevent any damage.
‣Comply with instructions in the safety data sheets for the chemicals used.
LWARNING
Thiocarbamide
Harmful if swallowed! Limited evidence of carcinogenicity! Possible risk of harm to the unborn
child! Dangerous for the environment with long-term effects!
‣Wear protective goggles, protective gloves and appropriate protective clothing.
‣Avoid all contact with the eyes, mouth and skin.
‣Avoid discharge into the environment.
Clean away fouling on the sensor as follows depending on the type of fouling:
1. Oily and greasy films:
Clean with fat solvent, e.g. alcohol, or hot water and agents containing surfactants
(alkaline) (e.g. dishwashing detergent).
2. Lime and metal hydroxide buildup and low solubility (lyophobic) organic buildup:
Dissolve buildup with diluted hydrochloric acid (3 %) and then rinse thoroughly with
plenty of clear water.
3. Sulfidic buildup (from flue gas desulfurization or wastewater treatment plants):
Use a mixture of hydrochloric acid (3 %) and thiocarbamide (commercially available)
and then rinse thoroughly with plenty of clear water.
4. Buildup containing proteins (e.g. food industry):
Use a mixture of hydrochloric acid (0.5 %) and pepsin (commercially available) and then
rinse thoroughly with plenty of clear water.
5. Readily soluble biological buildup:
Rinse with pressurized water.

Memosens CLL47E Repair
Endress+Hauser 9
After cleaning, rinse the sensor thoroughly with water.
6.2 Sensor calibration
‣Wall distance:
When calibrating, ensure that there is a minimum distance of 15 mm to the base and walls
of the calibration vessel.
7 Repair
7.1 General information
The repair and conversion concept provides for the following:
• The product has a modular design
• Only use original spare parts from the manufacturer
• Repairs are carried out by the manufacturer's Service Department or by trained users
• Observe applicable standards, national regulations and certificates
7.2 Return
The product must be returned if repairs or a factory calibration are required, or if the wrong
product was ordered or delivered. As an ISO-certified company and also due to legal
regulations, Endress+Hauser is obliged to follow certain procedures when handling any
returned products that have been in contact with medium.
To ensure the swift, safe and professional return of the device:
‣Refer to the website www.endress.com/support/return-material for information on the
procedure and conditions for returning devices.
7.3 Disposal
If required by the Directive 2012/19/EU on waste electrical and electronic equipment
(WEEE), the product is marked with the depicted symbol in order to minimize the disposal
of WEEE as unsorted municipal waste. Do not dispose of products bearing this marking as
unsorted municipal waste. Instead, return them to Endress+Hauser for disposal under the
applicable conditions.

Accessories Memosens CLL47E
10 Endress+Hauser
8 Accessories
The following are the most important accessories available at the time this documentation
was issued.
‣For accessories not listed here, please contact your Service or Sales Center.
8.1 Device-specific accessories
Memosens laboratory cable CYK20
• For digital sensors with Memosens technology
• Product Configurator on the product page: www.endress.com/cyk20
Memosens data cable CYK10
• For the use of digital sensors with Memosens technology outdoors
• Terminated cable, length 3 m (9.84 ft), M12 plug
• Order code: CYK10-A032
Technical Information TI00118C
Conductivity calibration solutions CLY11
Precision solutions referenced to SRM (Standard Reference Material) by NIST for qualified
calibration of conductivity measuring systems in accordance with ISO 9000
• CLY11-A, 74 μS/cm (reference temperature 25 °C (77 °F)), 500 ml (16.9 fl.oz)
Order No. 50081902
• CLY11-B, 149.6 μS/cm (reference temperature 25 °C (77 °F)), 500 ml (16.9 fl.oz)
Order No. 50081903
• CLY11-C, 1.406 mS/cm (reference temperature 25 °C (77 °F)), 500 ml (16.9 fl.oz)
Order No. 50081904
• CLY11-D, 12.64 mS/cm (reference temperature 25 °C (77 °F)), 500 ml (16.9 fl.oz)
Order No. 50081905
• CLY11-E, 107.00 mS/cm (reference temperature 25 °C (77 °F)), 500 ml (16.9 fl.oz)
Order No. 50081906
Technical Information TI00162C
8.2 Communication-specific accessories
Liquiline Mobile CML18
• Multiparameter mobile device for laboratory and field
• Reliable transmitter with display and app connection
• Product Configurator on the product page: www.endress.com/CML18
Operating Instructions BA02002C

Memosens CLL47E Technical data
Endress+Hauser 11
Memobase Plus CYZ71D
• PC software to support laboratory calibration
• Visualization and documentation of sensor management
• Sensor calibrations stored in database
• Product Configurator on the product page: www.endress.com/cyz71d
Technical Information TI00502C
9 Technical data
9.1 Input
9.1.1 Measured variables
• Conductivity
• Temperature
9.1.2 Measuring ranges
Conductivity 1) 5 µS/cm to 200 mS/cm
Temperature 0 to 100 °C (32 to 212 °F)
1) In relation to water at 25 °C (77 °F)
9.1.3 Cell constant
k = 0.57 cm-1
9.1.4 Temperature compensation
Pt1000 (Class A according to IEC 60751)
9.2 Performance characteristics
9.2.1 Measuring uncertainty
Each individual sensor is factory-measured in a solution with approx. 50 μS/cm using a
reference measuring system traceable to NIST or PTB. The exact cell constant is entered into
the manufacturer certificate supplied. The uncertainty of measurement in determining the cell
constant is 1.0 %.

Technical data Memosens CLL47E
12 Endress+Hauser
9.2.2 Maximum measured error
Conductivity
In the range 5 µS/cm to 1 mS/cm ≤ 2 % of reading
In the range 1 mS/cm to 200 mS/cm ≤ 4 % of reading
Temperature ≤ 1.0 K, in measuring range 0 to 100 °C
(32 to 212 °F)
9.2.3 Repeatability
Conductivity ≤ 0.5 % of reading, in specified measuring range
Temperature ≤ 0.5 K
9.3 Environment
9.3.1 Ambient temperature range
–20 to 60 °C (–4 to 140 °F)
9.3.2 Storage temperature
-25 to +80 °C (-13 to +176 °F)
9.3.3 Conditions for outdoor use
If the sensor is used outdoors, the following conditions apply to maintain the confirmed
specification:
• Connection via CYK10-A052 cable, use of spacer (protection against loss)
• Maximum 30 minutes
• Maximum twice per week
• Maximum insertion depth 5 m (16.4 ft)
• Maximum medium temperature 50 °C (122 °F)
9.3.4 Humidity
5 to 95 %
9.3.5 Degree of protection
IP 68 / NEMA type 6P (1.9 m water column, 20 °C, 24 h)

Memosens CLL47E Index
Endress+Hauser 13
Index
A
Ambient temperature range ........... 12
C
Cell constant .................... 11
Commissioning ....................7
D
Degree of protection
Technical data ................ 12
Disposal ........................9
Documentation ....................3
E
Environment .................... 12
I
Incoming acceptance ................ 5
Intended use ..................... 4
M
Maximum measured error ............ 12
Measured variables ................ 11
Measuring ranges ................. 11
Measuring uncertainty .............. 11
N
Nameplate ...................... 5
O
Operational safety ..................4
P
Performance characteristics ........... 11
Product identification ................ 5
Product safety .................... 5
R
Repair ......................... 9
Repeatability .................... 12
Return .........................9
S
Safety
Operational ...................4
Product ..................... 5
Workplace safety ............... 4
Safety instructions ..................4
Scope of delivery ...................6
Sensor
Calibration ................... 9
Cleaning .....................8
Storage temperature ................12
Symbols ........................ 3
T
Technical data
Environment ................. 12
Input ......................11
Performance characteristics ........ 11
Temperature compensation ............11
U
Use ...........................4
W
Warnings ....................... 3
Workplace safety .................. 4

www.addresses.endress.com
*71558607*
71558607