Endress+Hauser Proline Promag H 200 Manual

The measuring device for smallest flow rates with genuine two-wire
technology
Application
• The measuring principle is virtually independent of pressure,
density, temperature and viscosity
• For the smallest flow quantities and demanding hygienic
applications
Device properties
• Liner made of PFA
• Sensor housing made of stainless steel (3A, EHEDG)
• Wetted materials CIP, SIP cleanable
• Loop-powered technology
• Robust two-chamber housing
• Plant safety: worldwide approvals (SIL, Haz. area)
Your benefits
• Flexible installation concept – numerous hygienic process
connections
• Energy-saving flow measurement – no pressure loss due to
cross-section constriction
• Maintenance-free – no moving parts
• Convenient device wiring – separate connection
compartment
• Safe operation – no need to open the device due to display
with touch control, background lighting
• Integrated verification – Heartbeat Technology™
Products Solutions Services
Technical Information
Proline Promag H 200
Electromagnetic flowmeter
TI01061D/06/EN/05.17
71372370

Proline Promag H 200
2 Endress+Hauser
Table of contents
Document information ....................... 3
Symbols used ................................ 3
Function and system design ................... 3
Measuring principle ............................ 3
Measuring system ............................. 5
Safety ..................................... 5
Input ..................................... 5
Measured variable ............................. 5
Measuring range .............................. 5
Operable flow range ........................... 6
Output ................................... 6
Output signal ................................ 6
Signal on alarm ............................... 7
Load ...................................... 9
Ex connection data ............................ 9
Low flow cut off ............................. 13
Galvanic isolation ............................ 13
Protocol-specific data .......................... 13
Power supply ............................. 17
Terminal assignment .......................... 17
Pin assignment, device plug ...................... 18
Supply voltage .............................. 18
Power consumption ........................... 18
Current consumption .......................... 19
Power supply failure .......................... 19
Electrical connection .......................... 19
Potential equalization ......................... 23
Terminals ................................. 24
Cable entries ............................... 24
Cable specification ............................ 24
Overvoltage protection ......................... 25
Performance characteristics .................. 25
Reference operating conditions ................... 25
Maximum measured error ....................... 25
Repeatability ............................... 26
Influence of ambient temperature ................. 26
Installation ............................... 26
Mounting location ............................ 27
Orientation ................................ 27
Inlet and outlet runs .......................... 28
Adapters .................................. 28
Special mounting instructions .................... 29
Environment .............................. 29
Ambient temperature range ..................... 29
Storage temperature .......................... 30
Degree of protection .......................... 30
Shock resistance ............................. 30
Vibration resistance ........................... 30
Mechanical load ............................. 30
Electromagnetic compatibility (EMC) ............... 30
Process .................................. 30
Medium temperature range ...................... 30
Conductivity ................................ 31
Pressure-temperature ratings .................... 31
Pressure tightness ............................ 34
Flow limit ................................. 34
Pressure loss ............................... 34
System pressure ............................. 35
Vibrations ................................. 35
Mechanical construction .................... 35
Dimensions in SI units ......................... 35
Dimensions in US units ......................... 48
Weight ................................... 57
Measuring tube specification ..................... 57
Materials .................................. 58
Fitted electrodes ............................. 59
Process connections ........................... 59
Surface roughness ............................ 59
Operability ............................... 60
Operating concept ............................ 60
Local operation .............................. 60
Remote operation ............................ 61
Service interface ............................. 63
Certificates and approvals ................... 64
CE mark ................................... 64
C-Tick symbol ............................... 64
Ex approval ................................ 64
Sanitary compatibility ......................... 65
Functional safety ............................. 65
HART certification ............................ 65
FOUNDATION Fieldbus certification ................ 65
Certification PROFIBUS ......................... 65
Other standards and guidelines ................... 65
Ordering information ....................... 66
Application packages ....................... 66
Diagnostics functions .......................... 66
Heartbeat Technology ......................... 66
Accessories ............................... 67
Device-specific accessories ...................... 67
Communication-specific accessories ................ 68
Service-specific accessories ...................... 68
System components ........................... 69
Documentation ............................ 69
Standard documentation ........................ 69
Supplementary device-dependent documentation ....... 70
Registered trademarks ...................... 70

Proline Promag H 200
Endress+Hauser 3
Document information
Symbols used Electrical symbols
Symbol Meaning Symbol Meaning
Direct current Alternating current
Direct current and alternating current Ground connection
A grounded terminal which, as far as
the operator is concerned, is
grounded via a grounding system.
Protective ground connection
A terminal which must be connected
to ground prior to establishing any
other connections.
Equipotential connection
A connection that has to be connected
to the plant grounding system: This
may be a potential equalization line
or a star grounding system depending
on national or company codes of
practice.
Symbols for certain types of information
Symbol Meaning
Permitted
Procedures, processes or actions that are permitted.
Preferred
Procedures, processes or actions that are preferred.
Forbidden
Procedures, processes or actions that are forbidden.
Tip
Indicates additional information.
Reference to documentation
Reference to page
Reference to graphic
Visual inspection
Symbols in graphics
Symbol Meaning Symbol Meaning
1, 2, 3,... Item numbers
,… ,
Series of steps
A, B, C, ... Views A-A, B-B, C-C, ... Sections
-
Hazardous area
.
Safe area (non-hazardous area)
Flow direction
Function and system design
Measuring principle Following Faraday's law of magnetic induction, a voltage is induced in a conductor moving through a
magnetic field.

Proline Promag H 200
4 Endress+Hauser
I
L
B
I
Ue
v
A0017035
Ue Induced voltage
B Magnetic induction (magnetic field)
L Electrode spacing
I Current
v Flow velocity
In the electromagnetic measuring principle, the flowing medium is the moving conductor. The
voltage induced (Ue) is proportional to the flow velocity (v) and is supplied to the amplifier by means
of two measuring electrodes. The flow volume (Q) is calculated via the pipe cross-section (A). The DC
magnetic field is created through a switched direct current of alternating polarity.
Formulae for calculation
• Induced voltage Ue = B · L · v
• Volume flow Q = A · v

Proline Promag H 200
Endress+Hauser 5
Measuring system The device consists of a transmitter and a sensor.
The device is available as a compact version:
The transmitter and sensor form a mechanical unit.
Transmitter
Promag 200 Materials:
Aluminum, AlSi10Mg, coated
Configuration:
• External operation via four-line, illuminated local display with touch
control and guided menus ("Make-it-run" wizards) for applications
• Via operating tools (e.g. FieldCare)
A0013471
Sensor
Promag H Nominal diameter range: DN 2 to 25 (1/12 to 1")
Materials:
• Sensor housing: stainless steel 1.4301 (304)
• Measuring tubes: stainless steel, 1.4301 (304)
• Liner: PFA (USP Class VI; FDA 21 CFR 177.1550; 3A)
• Electrodes: stainless steel 1.4435 (F316L); Alloy C22, 2.4602 (UNS
N06022); tantalum; platinum
• Process connections: stainless steel, 1.4404 (F316L); PVDF; PVC
adhesive sleeve
• Seals: EPDM, FKM, Kalrez
• Grounding rings (only for DN 02 to 25 (1/12 to 1")): stainless steel,
1.4435 (F316L); Alloy C22, 2.4602 (UNS N06022); tantalum
A0017702
Safety IT security
We only provide a warranty if the device is installed and used as described in the Operating
Instructions. The device is equipped with security mechanisms to protect it against any inadvertent
changes to the device settings.
IT security measures in line with operators' security standards and designed to provide additional
protection for the device and device data transfer must be implemented by the operators themselves.
Input
Measured variable Direct measured variables
Volume flow (proportional to induced voltage)
Calculated measured variables
Mass flow
Measuring range Typically v = 0.01 to 10 m/s (0.03 to 33 ft/s) with the specified accuracy
Flow characteristic values in SI units
Nominal
diameter
Recommended
flow Factory settings
Min./max. full scale value
(v ~ 0.3/10 m/s)
Full scale value current
output
(v ~ 2.5 m/s)
Pulse value
(~ 2 pulse/s)
Low flow cut off
(v ~ 0.04 m/s)
[mm] [in] [dm3/min] [dm3/min] [dm3] [dm3/min]
2 1/12 0.06 to 1.8 0,5 0.005 0,01
4 1/8 0.25 to 7 2 0.025 0,05

Proline Promag H 200
6 Endress+Hauser
Nominal
diameter
Recommended
flow Factory settings
Min./max. full scale value
(v ~ 0.3/10 m/s)
Full scale value current
output
(v ~ 2.5 m/s)
Pulse value
(~ 2 pulse/s)
Low flow cut off
(v ~ 0.04 m/s)
[mm] [in] [dm3/min] [dm3/min] [dm3] [dm3/min]
8 3/8 1 to 30 8 0.1 0,1
15 ½ 4 to 100 25 0.2 0,5
25 1 9 to 300 75 0.5 1
Flow characteristic values in US units
Nominal
diameter
Recommended
flow Factory settings
Min./max. full scale value
(v ~ 0.3/10 m/s)
Full scale value current
output
(v ~ 2.5 m/s)
Pulse value
(~ 2 pulse/s)
Low flow cut off
(v ~ 0.04 m/s)
[in] [mm] [gal/min] [gal/min] [gal] [gal/min]
1/12 2 0.015 to 0.5 0,1 0,001 0,002
1/8 4 0.07 to 2 0,5 0,005 0,008
3/8 8 0.25 to 8 2 0,02 0,025
½ 15 1 to 27 6 0,05 0,1
1 25 2.5 to 80 18 0,2 0,25
To calculate the measuring range, use the Applicator sizing tool →  68
Recommended measuring range
"Flow limit" section →  34
Operable flow range Over 1000 : 1
Output
Output signal Current output
Current output 4-20 mA HART (passive)
Resolution < 1 µA
Damping Adjustable: 0.0 to 999.9 s
Assignable measured
variables
• Volume flow
• Mass flow
Pulse/frequency/switch output
Function Can be set to pulse, frequency or switch output
Version Passive, open collector
Maximum input values • DC 35 V
• 50 mA
For information on the Ex connection values →  9

Proline Promag H 200
Endress+Hauser 7
Voltage drop • For ≤ 2 mA: 2 V
• For 10 mA: 8 V
Residual current ≤ 0.05 mA
Pulse output
Pulse width Adjustable: 5 to 2 000 ms
Maximum pulse rate 100 Impulse/s
Pulse value Adjustable
Assignable measured
variables
• Volume flow
• Mass flow
Frequency output
Output frequency Adjustable: 0 to 1 000 Hz
Damping Adjustable: 0 to 999 s
Pulse/pause ratio 1:1
Assignable measured
variables
• Volume flow
• Mass flow
Switch output
Switching behavior Binary, conductive or non-conductive
Switching delay Adjustable: 0 to 100 s
Number of switching
cycles
Unlimited
Assignable functions • Off
• On
• Diagnostic behavior
• Limit value
– Volume flow
– Mass flow
• Flow direction monitoring
• Status
– Empty pipe detection
– Low flow cut off
FOUNDATION Fieldbus
Signal encoding Manchester Bus Powered (MBP)
Data transfer 31.25 KBit/s, Voltage mode
PROFIBUS PA
Signal encoding Manchester Bus Powered (MBP)
Data transfer 31.25 KBit/s, Voltage mode
Signal on alarm Depending on the interface, failure information is displayed as follows:
Current output
HART
Device diagnostics Device condition can be read out via HART Command 48

Proline Promag H 200
8 Endress+Hauser
Pulse/frequency/switch output
Pulse output
Failure mode Choose from:
• Actual value
• No pulses
Frequency output
Failure mode Choose from:
• Actual value
• 0 Hz
• Defined value: 0 to 1 250 Hz
Switch output
Failure mode Choose from:
• Current status
• Open
• Closed
FOUNDATION Fieldbus
Status and alarm
messages
Diagnostics in accordance with FF-912
Error current FDE (Fault
Disconnection Electronic)
0 mA
PROFIBUS PA
Status and alarm
messages
Diagnostics in accordance with PROFIBUS PA Profile 3.02
Error current FDE (Fault
Disconnection Electronic)
0 mA
Local display
Plain text display With information on cause and remedial measures
Backlight Additionally for device version with SD03 local display: red lighting indicates a
device error.
Status signal as per NAMUR recommendation NE 107
Operating tool
• Via digital communication:
– HART protocol
– FOUNDATION Fieldbus
– PROFIBUS PA
• Via service interface
Plain text display With information on cause and remedial measures
Additional information on remote operation →  61

Proline Promag H 200
Endress+Hauser 9
Load Load for current output: 0 to 500 Ω, depending on the external supply voltage of the power supply
unit
Calculation of the maximum load
Depending on the supply voltage of the power supply unit (US), the maximum load (RB) including
line resistance must be observed to ensure adequate terminal voltage at the device. In doing so,
observe the minimum terminal voltage
• For US = 18 to 18.9 V: RB ≤ (US - 18 V): 0.0036 A
• For US = 18.9 to 24.5 V: RB ≤ (US - 13.5 V): 0.022 A
• For US = 24.5 to 30 V: RB ≤ 500 Ω
0
100
200
300
400
500
14 16 18 20 22 24 26 28 30 32 U [V]
s
R [ ]
bW1.1 1.21
34 36
A0013563
1 Operating range
1.1 For order code for "Output", option A "4-20 mA HART"/option B "4-20 mA HART, pulse/frequency/switch
output" with Ex i
1.2 For order code for "Output", option A "4-20 mA HART"/option B "4-20 mA HART, pulse/frequency/switch
output" with non-Ex and Ex d
Sample calculation
Supply voltage of the power supply unit: US = 19 V
Maximum load: RB ≤ (19 V - 13.5 V): 0.022 A = 250 Ω
Ex connection data Safety-related values
Type of protection Ex d
Order code for "Output" Output type Safety-related values
Option A4-20mA HART Unom = DC 35 V
Umax = 250 V
Option B4-20mA HART Unom = DC 35 V
Umax = 250 V
Pulse/frequency/switch output Unom = DC 35 V
Umax = 250 V
Pmax = 1 W 1)
Option EFOUNDATION Fieldbus Unom = DC 32 V
Umax = 250 V
Pmax = 0.88 W
Pulse/frequency/switch output Unom = DC 35 V
Umax = 250 V
Pmax = 1 W 1)

Proline Promag H 200
10 Endress+Hauser
Order code for "Output" Output type Safety-related values
Option GPROFIBUS PA Unom = DC 32 V
Umax = 250 V
Pmax = 0.88 W
Pulse/frequency/switch output Unom = DC 35 V
Umax = 250 V
Pmax = 1 W 1)
1) Internal circuit limited by Ri = 760.5 Ω
Ex nA type of protection
Order code for "Output" Output type Safety-related values
Option A4-20mA HART Unom = DC 35 V
Umax = 250 V
Option B4-20mA HART Unom = DC 35 V
Umax = 250 V
Pulse/frequency/switch output Unom = DC 35 V
Umax = 250 V
Pmax = 1 W 1)
Option EFOUNDATION Fieldbus Unom = DC 32 V
Umax = 250 V
Pmax = 0.88 W
Pulse/frequency/switch output Unom = DC 35 V
Umax = 250 V
Pmax = 1 W 1)
Option GPROFIBUS PA Unom = DC 32 V
Umax = 250 V
Pmax = 0.88 W
Pulse/frequency/switch output Unom = DC 35 V
Umax = 250 V
Pmax = 1 W 1)
1) Internal circuit limited by Ri = 760.5 Ω
Type of protection XP
Order code for "Output" Output type Safety-related values
Option A4-20mA HART Unom = DC 35 V
Umax = 250 V
Option B4-20mA HART Unom = DC 35 V
Umax = 250 V
Pulse/frequency/switch output Unom = DC 35 V
Umax = 250 V
Pmax = 1 W 1)
Option EFOUNDATION Fieldbus Unom = DC 32 V
Umax = 250 V
Pmax = 0.88 W
Pulse/frequency/switch output Unom = DC 35 V
Umax = 250 V
Pmax = 1 W 1)

Proline Promag H 200
Endress+Hauser 11
Order code for "Output" Output type Safety-related values
Option GPROFIBUS PA Unom = DC 32 V
Umax = 250 V
Pmax = 0.88 W
Pulse/frequency/switch output Unom = DC 35 V
Umax = 250 V
Pmax = 1 W 1)
1) Internal circuit limited by Ri = 760.5 Ω
Intrinsically safe values
Type of protection Ex ia
Order code for "Output" Output type Intrinsically safe values
Option A4-20mA HART Ui = DC 30 V
Ii = 300 mA
Pi = 1 W
Li = 0 μH
Ci = 5 nF
Option B4-20mA HART Ui = DC 30 V
Ii = 300 mA
Pi = 1 W
Li = 0 μH
Ci = 5 nF
Pulse/frequency/switch output Ui = DC 30 V
Ii = 300 mA
Pi = 1 W
Li = 0 μH
Ci = 6 nF
Option EFOUNDATION Fieldbus STANDARD
Ui = 30 V
li = 300 mA
Pi = 1.2 W
Li = 10 µH
Ci = 5 nF
FISCO
Ui = 17.5 V
li = 550 mA
Pi = 5.5 W
Li = 10 µH
Ci = 5 nF
Pulse/frequency/switch output Ui = 30 V
li = 300 mA
Pi = 1 W
Li = 0 µH
Ci = 6 nF
Option GPROFIBUS PA STANDARD
Ui = 30 V
li = 300 mA
Pi = 1.2 W
Li = 10 µH
Ci = 5 nF
FISCO
Ui = 17.5 V
li = 550 mA
Pi = 5.5 W
Li = 10 µH
Ci = 5 nF
Pulse/frequency/switch output Ui = 30 V
li = 300 mA
Pi = 1 W
Li = 0 µH
Ci = 6 nF

Proline Promag H 200
12 Endress+Hauser
Type of protection Ex ic
Order code for "Output" Output type Intrinsically safe values
Option A4-20mA HART Ui = DC 35 V
Ii = n.a.
Pi = 1 W
Li = 0 μH
Ci = 5 nF
Option B4-20mA HART Ui = DC 35 V
Ii = n.a.
Pi = 1 W
Li = 0 μH
Ci = 5 nF
Pulse/frequency/switch output Ui = DC 35 V
Ii = n.a.
Pi = 1 W
Li = 0 μH
Ci = 6 nF
Option EFOUNDATION Fieldbus STANDARD
Ui = 32 V
li = 300 mA
Pi = n.a.
Li = 10 µH
Ci = 5 nF
FISCO
Ui = 17.5 V
li = n.a.
Pi = n.a.
Li = 10 µH
Ci = 5 nF
Pulse/frequency/switch output Ui = 35 V
li = 300 mA
Pi = 1 W
Li = 0 µH
Ci = 6 nF
Option GPROFIBUS PA STANDARD
Ui = 32 V
li = 300 mA
Pi = n.a.
Li = 10 µH
Ci = 5 nF
FISCO
Ui = 17.5 V
li = n.a.
Pi = n.a.
Li = 10 µH
Ci = 5 nF
Pulse/frequency/switch output Ui = 35 V
li = 300 mA
Pi = 1 W
Li = 0 µH
Ci = 6 nF
Type of protection IS
Order code for "Output" Output type Intrinsically safe values
Option A4-20mA HART Ui = DC 30 V
Ii = 300 mA
Pi = 1 W
Li = 0 μH
Ci = 5 nF
Option B4-20mA HART Ui = DC 30 V
Ii = 300 mA
Pi = 1 W
Li = 0 μH
Ci = 5 nF
Pulse/frequency/switch output Ui = DC 30 V
Ii = 300 mA
Pi = 1 W
Li = 0 μH
Ci = 6 nF

Proline Promag H 200
Endress+Hauser 13
Order code for "Output" Output type Intrinsically safe values
Option EFOUNDATION Fieldbus STANDARD
Ui = 30 V
li = 300 mA
Pi = 1.2 W
Li = 10 µH
Ci = 5 nF
FISCO
Ui = 17.5 V
li = 550 mA
Pi = 5.5 W
Li = 10 µH
Ci = 5 nF
Pulse/frequency/switch output Ui = 30 V
li = 300 mA
Pi = 1 W
Li = 0 µH
Ci = 6 nF
Option GPROFIBUS PA STANDARD
Ui = 30 V
li = 300 mA
Pi = 1.2 W
Li = 10 µH
Ci = 5 nF
FISCO
Ui = 17.5 V
li = 550 mA
Pi = 5.5 W
Li = 10 µH
Ci = 5 nF
Pulse/frequency/switch output Ui = 30 V
li = 300 mA
Pi = 1 W
Li = 0 µH
Ci = 6 nF
Low flow cut off The switch points for low flow cut off are user-selectable.
Galvanic isolation All outputs are galvanically isolated from one another.
Protocol-specific data HART
Manufacturer ID 0x11
Device type ID 0x48
HART protocol revision 7
Device description files
(DTM, DD)
Information and files under:
www.endress.com
HART load • Min. 250 Ω
• Max. 500 Ω
Dynamic variables Read out the dynamic variables: HART command 3
The measured variables can be freely assigned to the dynamic variables.
Measured variables for PV (primary dynamic variable)
• Off
• Volume flow
• Mass flow
Measured variables for SV, TV, QV (secondary, tertiary and quaternary
dynamic variable)
• Volume flow
• Mass flow
• Totalizer 1
• Totalizer 2
• Totalizer 3
Device variables Read out the device variables: HART command 9
The device variables are permanently assigned.
FOUNDATION Fieldbus
Manufacturer ID 0x452B48
Ident number 0x1048
Device revision 1

Proline Promag H 200
14 Endress+Hauser
DD revision Information and files under:
•www.endress.com
•www.fieldbus.org
CFF revision
Device Tester Version (ITK
version)
6.1.1
ITK Test Campaign Number IT094200
Link Master capability (LAS) Yes
Choice of "Link Master" and
"Basic Device"
Yes
Factory setting: Basic Device
Node address Factory setting: 247 (0xF7)
Supported functions The following methods are supported:
• Restart
• ENP Restart
• Diagnostic
Virtual Communication Relationships (VCRs)
Number of VCRs 44
Number of link objects in VFD 50
Permanent entries 1
Client VCRs 0
Server VCRs 10
Source VCRs 43
Sink VCRs 0
Subscriber VCRs 43
Publisher VCRs 43
Device Link Capabilities
Slot time 4
Min. delay between PDU 8
Max. response delay Min. 5
Transducer Blocks
Block Contents Output values
Setup Transducer Block
(TRDSUP)
All parameters for standard commissioning. No output values
Advanced Setup
Transducer Block
(TRDASUP)
All parameters for more accurate measurement
configuration.
No output values
Display Transducer
Block
(TRDDISP)
Parameters for configuring the local display. No output values
HistoROM Transducer
Block
(TRDHROM)
Parameters for using the HistoROM function. No output values
Diagnostic Transducer
Block
(TRDDIAG)
Diagnostics information. Process variables (AI Channel)
• Temperature (7)
• Volume flow (9)
• Mass flow (11)
Expert Configuration
Transducer Block
(TRDEXP)
Parameters that require the user to have in-
depth knowledge of the operation of the device
in order to configure the parameters
appropriately.
No output values

Proline Promag H 200
Endress+Hauser 15
Block Contents Output values
Expert Information
Transducer Block
(TRDEXPIN)
Parameters that provide information about the
state of the device.
No output values
Service Sensor
Transducer Block
(TRDSRVS)
Parameters that can only be accessed by Endress
+Hauser Service.
No output values
Service Information
Transducer Block
(TRDSRVIF)
Parameters that provide Endress+Hauser Service
with information about the state of the device.
No output values
Total Inventory
Counter Transducer
Block
(TRDTIC)
Parameters for configuring all the totalizers and
the inventory counter.
Process variables (AI Channel)
• Totalizer 1 (16)
• Totalizer 2 (17)
• Totalizer 3 (18)
Heartbeat Technology
Transducer Block
(TRDHBT)
Parameters for the configuration and
comprehensive information about the results of
the verification.
No output values
Heartbeat Results 1
Transducer Block
(TRDHBTR1)
Information about the results of the verification. No output values
Heartbeat Results 2
Transducer Block
(TRDHBTR2)
Information about the results of the verification. No output values
Heartbeat Results 3
Transducer Block
(TRDHBTR3)
Information about the results of the verification. No output values
Heartbeat Results 4
Transducer Block
(TRDHBTR4)
Information about the results of the verification. No output values
Function blocks
Block Number
of
blocks
Contents Process variables (Channel)
Resource Block
(RB)
1 This Block (extended functionality) contains
all the data that uniquely identify the device; it
is the equivalent of an electronic nameplate
for the device.
–
Analog Input
Block
(AI)
4 This Block (extended functionality) receives
the measurement data provided by the Sensor
Block (can be selected via a channel number)
and makes the data available for other blocks
at the output.
Execution time: 25 ms
Process variables (AI Channel)
• Temperature (7)
• Volume flow (9)
• Mass flow (11)
Discrete Input
Block
(DI)
2 This Block (standard functionality) receives a
discrete value (e.g. indicator that measuring
range has been exceeded) and makes the
value available for other blocks at the output.
Execution time: 19 ms
• Switch output state (101)
• Empty pipe detection (102)
• Low flow cut off (103)
• Status verification (105)
PID Block
(PID)
1 This Block (standard functionality) acts as a
proportional-integral-differential controller
and can be used universally for control in the
field. It enables cascading and feedforward
control.
Execution time: 25 ms
–

Proline Promag H 200
16 Endress+Hauser
Block Number
of
blocks
Contents Process variables (Channel)
Multiple Digital
Output Block
(MDO)
1 This Block (standard functionality) receives
several discrete values and makes them
available for other blocks at the output.
Execution time: 19 ms
Channel_DO (122)
• Value 1: Reset totalizer 1
• Value 2: Reset totalizer 2
• Value 3: Reset totalizer 3
• Value 4: Flow override
• Value 5: Start heartbeat
verification
• Value 6: Status switch output
• Value 7: Not assigned
• Value 8: Not assigned
Integrator Block
(IT)
1 This Block (standard functionality) integrates
a measured variable over time or totalizes the
pulses from a Pulse Input Block. The Block can
be used as a totalizer that totalizes until a
reset, or as a batch totalizer whereby the
integrated value is compared against a target
value generated before or during the control
routine and generates a binary signal when
the target value is reached.
Execution time: 21 ms
–
PROFIBUS PA
Manufacturer ID 0x11
Ident number 0x1563
Profile version 3.02
Device description files (GSD,
DTM, DD)
Information and files under:
•www.endress.com
•www.profibus.org
Output values
(from measuring device to
automation system)
Analog input 1 to 2
• Mass flow
• Volume flow
Digital input 1 to 2
• Empty pipe detection
• Low flow cut off
• Status switch output
• Status verification
Totalizer 1 to 3
• Mass flow
• Volume flow
• Corrected volume flow
Input values
(from automation system to
measuring device)
Digital output 1 to 3 (fixed assignment)
• Digital output 1: switch positive zero return on/off
• Digital output 2: switch switch output on/off
• Digital output 3: start verification
Totalizer 1 to 3
• Totalize
• Reset and hold
• Preset and hold
• Operating mode configuration:
– Net flow total
– Forward flow total
– Reverse flow total

Proline Promag H 200
Endress+Hauser 17
Supported functions • Identification & Maintenance
Simplest device identification on the part of the control system and
nameplate
• PROFIBUS upload/download
Reading and writing parameters is up to ten times faster with PROFIBUS
upload/download
• Condensed status
Simplest and self-explanatory diagnostic information by categorizing
diagnostic messages that occur
Configuration of the device
address
• DIP switches on the I/O electronics module
• Local display
• via operating tools (e.g. FieldCare)
Power supply
Terminal assignment Transmitter
Connection versions
–
4
+
1
–
2
+
3
1
23
A0013570
+
1
–
2
–
4
+
3
1
23
A0018161
Maximum number of terminals, without integrated
overvoltage protection
Maximum number of terminals, with integrated
overvoltage protection
1
2
3
Output 1 (passive): supply voltage and signal transmission
Output 2 (passive): supply voltage and signal transmission
Ground terminal for cable shield
Order code for "Output" Terminal numbers
Output 1 Output 2
1 (+) 2 (-) 3 (+) 4 (-)
Option A4-20 mA HART (passive) -
Option B 1) 4-20 mA HART (passive) Pulse/frequency/switch output
(passive)
Option E 1) 2) FOUNDATION Fieldbus Pulse/frequency/switch output
(passive)
Option G 1) 3) PROFIBUS PA Pulse/frequency/switch output
(passive)
1) Output 1 must always be used; output 2 is optional.
2) FOUNDATION Fieldbus with integrated reverse polarity protection.
3) PROFIBUS PA with integrated reverse polarity protection.

Proline Promag H 200
18 Endress+Hauser
Pin assignment, device plug PROFIBUS PA
Device plug for signal transmission (device side)
1
2
4
3
A0019021
Pin Assignment Coding Plug/socket
1 + PROFIBUS PA + A Plug
2 Grounding
3 - PROFIBUS PA –
4 Not assigned
FOUNDATION Fieldbus
Device plug for signal transmission (device side)
1
2
4
3
A0019021
Pin Assignment Coding Plug/socket
1 + Signal + A Plug
2 - Signal –
3 Not assigned
4 Grounding
Supply voltage Transmitter
An external power supply is required for each output.
Order code for "Output" Minimum
terminal voltage
Maximum
terminal voltage
Option A 1) 2): 4-20 mA HART • For 4 mA: ≥ DC 18 V
• For 20 mA: ≥ DC 14 V DC 35 V
Option B 1) 2): 4-20 mA HART, pulse/frequency/
switch output
• For 4 mA: ≥ DC 18 V
• For 20 mA: ≥ DC 14 V DC 35 V
Option E 3): FOUNDATION Fieldbus, pulse/
frequency/switch output
≥ DC 9 V DC 32 V
Option G 3): PROFIBUS PA, pulse/frequency/switch
output
≥ DC 9 V DC 32 V
1) External supply voltage of the power supply unit with load.
2) For device versions with SD03 local display: The terminal voltage must be increased by DC 2 V if
backlighting is used.
3) For device version with SD03 local display: The terminal voltage must be increased by DC 0.5 V if
backlighting is used.
For information about the load see →  9
Various power supply units can be ordered from Endress+Hauser: see "Accessories" section
→  69
For information on the Ex connection values →  9
Power consumption Transmitter
Order code for "Output" Maximum power consumption
Option A: 4-20 mA HART 770 mW
Option B: 4-20 mA HART, pulse/
frequency/switch output
• Operation with output 1: 770 mW
• Operation with output 1 and 2: 2 770 mW

Proline Promag H 200
Endress+Hauser 19
Order code for "Output" Maximum power consumption
Option E: FOUNDATION Fieldbus, pulse/
frequency/switch output
• Operation with output 1: 576 mW
• Operation with output 1 and 2: 2 576 mW
Option G: PROFIBUS PA, pulse/frequency/
switch output
• Operation with output 1: 512 mW
• Operation with output 1 and 2: 2 512 mW
For information on the Ex connection values →  9
Current consumption Current output
For every 4-20 mA or 4-20 mA HART current output: 3.6 to 22.5 mA
If the option Defined value is selected in the Failure mode parameter : 3.59 to 22.5 mA
PROFIBUS PA
16 mA
FOUNDATION Fieldbus
16 mA
Power supply failure • Totalizers stop at the last value measured.
• Configuration is retained in the device memory (HistoROM).
• Error messages (incl. total operated hours) are stored.
Electrical connection Connecting the transmitter
1
2
A0015510
1 Cable entry for output 1
2 Cable entry for output 2

Proline Promag H 200
20 Endress+Hauser
Connection examples
Current output 4-20 mA HART
23
4...20 mA
41
+
-
5
+
-
A0015511
 1 Connection example for 4-20 mA HART current output (passive)
1 Automation system with current input (e.g. PLC)
2 Active barrier for power supply with integrated resistor for HART communication (≥ 250 Ω)(e.g. RN221N)
Connection for HART operating devices →  61
Observe the maximum load →  9
3 Cable shield, observe cable specifications
4 Analog display unit: observe maximum load →  9
5 Transmitter
Pulse/frequency output
1
+
_
12345
2
+
–
+
–
3
A0016801
 2 Connection example for pulse/frequency output (passive)
1 Automation system with pulse/frequency input (e.g. PLC)
2 Power supply
3 Transmitter: observe input values →  6
Switch output
1
+
_
+
_
2
+
_3
A0016802
 3 Connection example for switch output (passive)
1 Automation system with switch input (e.g. PLC)
2 Power supply
3 Transmitter: observe input values