Endress+Hauser Proline Promass 83 User manual

BA065D/06/en/12.06
71035081
Valid as of version
V 2.00.XX (device software)
Operating Instructions
Proline Promass 83
FOUNDATION Fieldbus
Coriolis Mass Flow Measuring System
9

Brief operating instructions Proline Promass 83 FOUNDATION Fieldbus
2Endress+Hauser
Brief operating instructions
These brief operating instructions show you how to configure your measuring device quickly and
easily:
!Note!
Always start troubleshooting with the checklist on Page 73 if faults occur after commissioning or
during operation. The routine takes you directly to the cause of the problem and the appropriate
remedial measures.
Safety instructions Page 7
Æ
Installation Page 13
Æ
Wiring Page 24
Æ
Quick operation guide Page 33
Æ
Operating programs Page 41
The measuring device can be configured and operated using the local display and using operating programs from various
manufacturers.
Æ
Basic configuration (device parameters, automation functions) Page 51 ff.
Configuration programs from various manufacturers can be used to configure device-specific parameters and to specify
automation functions for the FOUNDATION Fieldbus.
!Note!
If the measuring device is equipped with a local display, device-specific parameters and functions can be configured easily
and quickly using the "Commissioning" Quick Setup menu, e.g. language of the UI, measured variables, engineering
units, etc. →see next page.
Æ
FOUNDATION Fieldbus interface Page 45 ff.
Commissioning the FOUNDATION Fieldbus interface.
Æ
Hardware settings Page 43
Information on setting the HW write protection.
Æ
Customer-specific configuration
Complex measurement tasks require additional functions to be configured that the user can individually select, set and
adapt to his process conditions by setting the appropriate parameters. You have two options:
• Parameterization using the configuration program (FOUNDATION Fieldbus) →Page 45 ff.
• Parameterization using the local display (optional) →Page 51 ff.
!Note!
All functions and device parameters are described in detail in the Description of Device Functions manual, which is a
separate part of these Operating Instructions.
Æ
Data storage Page 55
The configuration of the transmitter can be stored on the integrated T-DAT data storage device.
!Note!
For time-saving commissioning, the settings stored in the T-DAT can be transmitted:
• For equivalent measuring points (equivalent configuration)
• In the event of device/board replacement.

Proline Promass 83 FOUNDATION Fieldbus Brief operating instructions
Endress+Hauser 3
QUICK SETUP "Commissioning"
!Note!
More detailed information on running Quick Setup menus, especially for devices without a local
display, can be found in the "Commissioning" section →Page 51 ff.
a0004740-en
Fig. 1: Quick Setup for straightforward commissioning
6461
0421 6462
6463
6464
2000
1002
B
+
++
EE
Esc
E
+
-
XXX.XXX.XX
HOME-POSITION
0402 04040400 0420 0422
3001 6460
3001
1004
m
n
o
p
Yes
Yes
No
No
No
Reference Calculated
Fix. Density
Density
Unit
Ref. Density Exp. Coeff. Lin
Exp. Coeff. SQR
Reference temp.
Volume flow Corr. Vol. flowMass flow Density Temperature Quit
Unit
Volume flow Unit Corr. Vol. flow
Unit
Mass flow Unit
Density Unit
Temperature
Unit
Totalizer Corr. Vol.
calculation
Unit
Totalizer
Language
Pre-setting
Quick Setup QS
Commission
Gas
measurement
Selection pre-settings Actual SettingsDeliver Settingsy
Selection
System units
Automatic parameterization
of the display
Carrying out the selected
Quick Setup Quick Setup
complete
Autom. Configuration
of Display?
Another
Quick Setup?
mThe DELIVERY SETTINGS option sets every selected unit to the factory setting.
The ACTUAL SETTINGS option accepts the units you previously configured.
nOnly units not yet configured in the current Setup are offered for selection in each cycle. The unit for mass, volume
and corrected volume is derived from the corresponding flow unit.
oThe YES option remains visible until all the units have been configured.
NO is the only option displayed when no further units are available.
pThe "automatic parameterization of the display" option contains the following basic settings/factory settings:
YES Main line = Mass flow
Additional line = Totalizer 1
Information line = Operating/system conditions
NO The existing (selected) settings remain.

Brief operating instructions Proline Promass 83 FOUNDATION Fieldbus
4Endress+Hauser
!Note!
• The display returns to the cell SETUP COMMISSIONING (1002) if you press the Xkey
combination during parameter interrogation. The stored parameters remain valid.
• The system units selected via the Quick Setup are only valid for the local display and for
parameters in the Transducer Blocks. They have no effect on the process variables which are
transmitted via the FOUNDATION Fieldbus.

Proline Promass 83 FOUNDATION Fieldbus Table of contents
Endress+Hauser 5
Table of contents
1 Safety instructions . . . . . . . . . . . . . . . . 7
1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.2 Installation, commissioning and operation . . . . . . . . 7
1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.4 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.5 Notes on safety conventions and icons . . . . . . . . . . . 8
2 Identification . . . . . . . . . . . . . . . . . . . . 9
2.1 Device designation . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1.1 Nameplate of the transmitter . . . . . . . . . . . . 9
2.1.2 Nameplate of the sensor . . . . . . . . . . . . . . 10
2.1.3 Nameplate for connections . . . . . . . . . . . . 11
2.2 Certificates and approvals . . . . . . . . . . . . . . . . . . . 12
2.3 FOUNDATION Fieldbus device certification . . . . . 12
2.4 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . 12
3 Installation . . . . . . . . . . . . . . . . . . . . . 13
3.1 Incoming acceptance, transport and storage . . . . . . 13
3.1.1 Incoming acceptance . . . . . . . . . . . . . . . . . 13
3.1.2 Transport . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1.3 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2 Installation conditions . . . . . . . . . . . . . . . . . . . . . . 14
3.2.1 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2.2 Mounting location . . . . . . . . . . . . . . . . . . . 14
3.2.3 Orientation . . . . . . . . . . . . . . . . . . . . . . . . 16
3.2.4 Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.2.5 Thermal insulation . . . . . . . . . . . . . . . . . . 19
3.2.6 Inlet and outlet runs . . . . . . . . . . . . . . . . . 19
3.2.7 Vibrations . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.2.8 Limiting flow . . . . . . . . . . . . . . . . . . . . . . . 19
3.3 Installation instructions . . . . . . . . . . . . . . . . . . . . . 20
3.3.1 Turning the transmitter housing . . . . . . . . 20
3.3.2 Installing the wall-mount housing . . . . . . . 21
3.3.3 Turning the local display . . . . . . . . . . . . . . 23
3.4 Post-installation check . . . . . . . . . . . . . . . . . . . . . . 23
4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . 24
4.1 FOUNDATION Fieldbus cable specification . . . . . . 24
4.1.1 Cable type . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.1.2 Maximum overall cable length . . . . . . . . . . 25
4.1.3 Maximum spur length . . . . . . . . . . . . . . . . 25
4.1.4 Number of field devices . . . . . . . . . . . . . . . 25
4.1.5 Shielding and grounding . . . . . . . . . . . . . . 25
4.1.6 Bus termination . . . . . . . . . . . . . . . . . . . . . 26
4.1.7 Further information . . . . . . . . . . . . . . . . . . 26
4.2 Connecting the remote version . . . . . . . . . . . . . . . 27
4.2.1 Connecting the connecting cable for sensor/
transmitter . . . . . . . . . . . . . . . . . . . . . . . . 27
4.2.2 Cable specification, connecting cable . . . . . 28
4.3 Connecting the measuring unit . . . . . . . . . . . . . . . 28
4.3.1 Connecting the transmitter . . . . . . . . . . . . 28
4.3.2 Fieldbus connector . . . . . . . . . . . . . . . . . . 30
4.3.3 Terminal assignment . . . . . . . . . . . . . . . . 31
4.4 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . 31
4.5 Post-connection check . . . . . . . . . . . . . . . . . . . . . . 32
5 Operation . . . . . . . . . . . . . . . . . . . . . . 33
5.1 Quick operation guide . . . . . . . . . . . . . . . . . . . . . . 33
5.2 Local display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
5.2.1 Display and operating elements . . . . . . . . . 34
5.2.2 Display (operating mode) . . . . . . . . . . . . . . 35
5.2.3 Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
5.3 Brief operating instructions on the function matrix . 38
5.3.1 General notes . . . . . . . . . . . . . . . . . . . . . . 39
5.3.2 Enabling the programming mode . . . . . . . . 39
5.3.3 Disabling the programming mode . . . . . . . . 40
5.4 Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
5.4.1 Type of error . . . . . . . . . . . . . . . . . . . . . . . 40
5.4.2 Error message type . . . . . . . . . . . . . . . . . . . 40
5.5 Operating programs . . . . . . . . . . . . . . . . . . . . . . . . 41
5.5.1 Operating program
"ToF Tool - Fieldtool Package" . . . . . . . . . . 41
5.5.2 Operating via FOUNDATION Fieldbus
configuration programs . . . . . . . . . . . . . . . 41
5.5.3 Device description files
for operating programs . . . . . . . . . . . . . . . 42
5.6 FOUNDATION Fieldbus hardware settings . . . . . . 43
5.6.1 Switching hardware write protection
on and off . . . . . . . . . . . . . . . . . . . . . . . . . 43
6 Commissioning . . . . . . . . . . . . . . . . . . 44
6.1 Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
6.2 Switching on the measuring device . . . . . . . . . . . . 44
6.3 Commissioning via FOUNDATION Fieldbus . . . . . 45
6.4 Commissioning via Quick Setup (local display) . . . . 51
6.4.1 Quick Setup "Commissioning" . . . . . . . . . . 51
6.4.2 Quick Setup "Gas Measurement" . . . . . . . . 53
6.4.3 Data backup/transmission . . . . . . . . . . . . 55
6.5 Device configuration . . . . . . . . . . . . . . . . . . . . . . . 56
6.5.1 Concentration measurement . . . . . . . . . . . 56
6.5.2 Advanced diagnostic functions . . . . . . . . . . 61
6.6 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
6.6.1 Zero point adjustment . . . . . . . . . . . . . . . . 63
6.6.2 Density adjustment . . . . . . . . . . . . . . . . . . 65
6.7 Gas measurement . . . . . . . . . . . . . . . . . . . . . . . . . 68
6.8 Purge and pressure monitoring connections . . . . . . 69
6.9 Data storage device (HistoROM), F-CHIP . . . . . . . . 69
6.9.1 HistoROM/S-DAT (sensor-DAT) . . . . . . . . 69
6.9.2 HistoROM/T-DAT (transmitter-DAT) . . . . 69
6.9.3 F-CHIP (Function-Chip) . . . . . . . . . . . . . . . 69
7 Maintenance . . . . . . . . . . . . . . . . . . . . 70
7.1 Exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 70
7.2 Cleaning with pigs (Promass H, I, S, P) . . . . . . . . . . 70
7.3 Replacing seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Proline Promass 83 FOUNDATION Fieldbus Table of contents
6Endress+Hauser
8 Accessories . . . . . . . . . . . . . . . . . . . . . 71
8.1 Device-specific accessories: . . . . . . . . . . . . . . . . . 71
8.2 Measuring principle-specific accessories: . . . . . . . . 71
8.3 Service-specific accessories: . . . . . . . . . . . . . . . . . . 72
9 Troubleshooting . . . . . . . . . . . . . . . . . 73
9.1 Troubleshooting instructions . . . . . . . . . . . . . . . . . 73
9.2 System/process error messages . . . . . . . . . . . . . . . 77
9.2.1 List of system error messages . . . . . . . . . . 78
9.2.2 List of process error messages . . . . . . . . . . . 84
9.3 Process errors without messages . . . . . . . . . . . . . . 86
9.4 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
9.5 Removing and installing electronics boards . . . . . . . 88
9.5.1 Field housing: removing and installing
electronics boards (Fig. 35) . . . . . . . . . . . . 88
9.5.2 Wall-mount housing: removing and
installing electronics boards (Fig. 36) . . . . . 90
9.6 Replacing the device fuse . . . . . . . . . . . . . . . . . . . . 92
9.7 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
9.8 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
9.9 Software history . . . . . . . . . . . . . . . . . . . . . . . . . . 93
10 Technical data . . . . . . . . . . . . . . . . . . . 95
10.1 Technical data at a glance . . . . . . . . . . . . . . . . . . . 95
10.1.1 Applications . . . . . . . . . . . . . . . . . . . . . . . . 95
10.1.2 Function and system design . . . . . . . . . . . . 95
10.1.3 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
10.1.4 Output . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
10.1.5 Power supply . . . . . . . . . . . . . . . . . . . . . . 100
10.1.6 Performance characteristics . . . . . . . . . . . 101
10.1.7 Operating conditions: Installation . . . . . . . 107
10.1.8 Operating conditions: Environment . . . . . 107
10.1.9 Operating conditions: Process . . . . . . . . . 108
10.1.10 Mechanical construction . . . . . . . . . . . . . 118
10.1.11 Human interface . . . . . . . . . . . . . . . . . . . 123
10.1.12 Certificates and approvals . . . . . . . . . . . . 124
10.1.13 Ordering information . . . . . . . . . . . . . . . 124
10.1.14 Accessories . . . . . . . . . . . . . . . . . . . . . . . 125
10.1.15 Documentation . . . . . . . . . . . . . . . . . . . 125
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126

Proline Promass 83 FOUNDATION Fieldbus Safety instructions
Endress+Hauser 7
1 Safety instructions
1.1 Designated use
The measuring device described in these Operating Instructions is to be used only for measuring the
mass flow rate of liquids and gases. At the same time, the system also measures fluid density and
fluid temperature. These parameters are then used to calculate other variables such as volume flow.
Fluids with widely differing properties can be measured.
Examples:
• Chocolate, condensed milk, liquid sugar
• Oils, fats
• Acids, alkalis, lacquers, paints, solvents and cleaning agents
• Pharmaceuticals, catalysts, inhibitors
• Suspensions
• Gases, liquefied gases, etc.
Resulting from incorrect use or from use other than that designated the operational safety of the
measuring devices can be suspended. The manufacturer accepts no liability for damages being
produced from this.
1.2 Installation, commissioning and operation
Note the following points:
• Installation, connection to the electricity supply, commissioning and maintenance of the device
must be carried out by trained, qualified specialists authorized to perform such work by the
facility's owner-operator. The specialist must have read and understood these Operating
Instructions and must follow the instructions they contain.
• The device must be operated by persons authorized and trained by the facility's owner-operator.
Strict compliance with the instructions in these Operating Instructions is mandatory.
• Endress+Hauser will be happy to assist in clarifying the corrosion-resistant properties of materials
wetted by special fluids, including fluids used for cleaning. However, minor changes in
temperature, concentration or in the degree of contamination in the process may result in
variations in corrosion resistance. For this reason, Endress+Hauser does not accept any
responsibility with regard to the corrosion resistance of materials wetted by fluids in a specific
application. The user is responsible for the choice of suitable wetted materials in the process.
• If carrying out welding work on the piping, the welding unit may not be grounded by means of
the measuring device.
• The installer must ensure that the measuring system is correctly wired in accordance with the
wiring diagrams. The transmitter must be grounded, unless the power supply is galvanically
isolated.
• Invariably, local regulations governing the opening and repair of electrical devices apply.
1.3 Operational safety
Note the following points:
• Measuring systems for use in hazardous environments are accompanied by separate "Ex
documentation", which is an integral part of these Operating Instructions. Strict compliance with
the installation instructions and ratings as stated in this supplementary documentation is
mandatory.
The symbol on the front of this supplementary Ex documentation indicates the approval and the
certification body ( 0 Europe, 2USA, 1Canada).
• The measuring device complies with the general safety requirements in accordance with
EN 61010-1 , the EMC requirements of EN 61326/A1, and NAMUR recommendation NE 21,
NE 43 and NE 53.
• For measuring systems used in SIL 2 applications, the separate manual on functional safety must
be observed.

Safety instructions Proline Promass 83 FOUNDATION Fieldbus
8Endress+Hauser
• The manufacturer reserves the right to modify technical data without prior notice. Your
Endress+Hauser distributor will supply you with current information and updates to these
Operating Instructions.
1.4 Return
The following procedures must be carried out before a flowmeter requiring repair or calibration, for
example, is returned to Endress+Hauser:
• Always enclose a duly completed "Declaration of contamination" form. Only then can
Endress+Hauser transport, examine and repair a returned device.
• Enclose special handling instructions if necessary, for example a safety data sheet as per
EN 91/155/EEC.
• Remove all residues. Pay special attention to the grooves for seals and crevices which could
contain residues. This is particularly important if the substance is hazardous to health, e.g.
flammable, toxic, caustic, carcinogenic, etc.
With Promass A and Promass M the threaded process connections must first be removed from the
sensor and then cleaned.
!Note!
You will find a preprinted "Declaration of contamination" form at the back of this manual.
#Warning!
• Do not return a measuring device if you are not absolutely certain that all traces of hazardous
substances have been removed, e.g. substances which have penetrated crevices or diffused
through plastic.
• Costs incurred for waste disposal and injury (burns, etc.) due to inadequate cleaning will be
charged to the owner-operator.
1.5 Notes on safety conventions and icons
The devices are designed to meet state-of-the-art safety requirements, have been tested, and left the
factory in a condition in which they are safe to operate. The devices comply with the applicable
standards and regulations in accordance with EN 61010-1 "Protection Measures for Electrical
Equipment for Measurement, Control, Regulation and Laboratory Procedures". The devices can,
however, be a source of danger if used incorrectly or for other than the designated use.
Consequently, always pay particular attention to the safety instructions indicated in these Operating
Instructions by the following icons:
#Warning!
"Warning" indicates an action or procedure which, if not performed correctly, can result in injury
or a safety hazard. Comply strictly with the instructions and proceed with care.
"Caution!
"Caution" indicates an action or procedure which, if not performed correctly, can result in incorrect
operation or destruction of the device. Comply strictly with the instructions.
!Note!
"Note" indicates an action or procedure which, if not performed correctly, can have an indirect
effect on operation or trigger an unexpected response on the part of the device.

Proline Promass 83 FOUNDATION Fieldbus Identification
Endress+Hauser 9
2 Identification
2.1 Device designation
The flow measuring system consists of the following components:
• Transmitter Promass 80 and 83
• Sensor (Promass F, Promass M, Promass E, Promass A, Promass H, Promass I, Promass S or
Promass P)
Two versions are available:
• Compact version: transmitter and sensor form a single mechanical unit.
• Remote version: transmitter and sensor are installed separately.
2.1.1 Nameplate of the transmitter
a0004707
Fig. 2: Nameplate specifications for the "Promass 83" transmitter (example)
1 Ordering code/serial number: see the specifications on the order confirmation for the meanings of the individual
letters and digits.
2 Power supply/frequency: 20 to 55 V AC / 16 to 62 V DC / 50 to 60 Hz
Power consumption: 15 VA / 15 W
3 FOUNDATION Fieldbus: equipped with FOUNDATION Fieldbus-H1 interface
ITK 5.0: certified by the Fieldbus Foundation; Interoperability Test Kit, revision 5.0
DEVICE ID: FOUNDATION Fieldbus device identification
4Reservedforinformation on special products
5 Ambient temperature range
6 Degree of protection
Order Code:
Ser.No.:
TAG No.:
i
Pat. US 4,768,384
Pat. US 6,412,355 6,453,753
EP 618 680EP 262 573
5,648,616
4,801,897
Pat. EP 261 435
Pat. US 5,479,007
83F25-XXXXXXXXXXXX
12345678901
ABCDEFGHJKLMNPQRST
20-55VAC/16-62VDC
50-60Hz 15VA/W
IP67 / NEMA/Type 4X
FEK0713 -20°C (-4°F) < Tamb < +60°C (+140°F)
OUNDATION F
R
FOUNDATION Fieldbus ITK 5.0
DEVICE ID 452B481051-12345678901
1
6
5
2
3
4
Promass 83
N12895

Identification Proline Promass 83 FOUNDATION Fieldbus
10 Endress+Hauser
2.1.2 Nameplate of the sensor
a0004688
Fig. 3: Nameplate specifications for the "Promass F" sensor (example)
1 Ordering code/serial number: see the specifications on the order confirmation for the meanings of the individual
letters and digits.
2 Calibration factor with zero point
3 Device nominal diameter/nominal pressure
4 Flange nominal diameter/nominal pressure
5 Measuring tube material
6 Max. fluid temperature
7 Secondary containment pressure range
8 Density accuracy
9 Additional information (examples):
– 5P-CAL: with 5-point calibration
– 3.1 B: with 3.1 B certificate for wetted materials
10 Reserved for information on special products
11 Ambient temperature range
12 Degree of protection
13 Flow direction
14 Reserved for additional information on device version (approvals, certificates)
1
2
4
5
6
7
8
912
13
14
3
11
DN25 / 1” Size:
-20°C (-4°F) < Tamb < +60°C (+140°F)
Pat. US 5,796,011
i
NEMA/Type 4X
ABCDEFGHJKLMNPQRST
12345678901
2.5100 / -11
83F25-XXXXXXXXXXXX
DN25 DIN/EN PN100
1.4539 / 904L
200°C / 392°F
40bar / 600psi Container
5P-CAL, 3.1
+/- 0.001g/cc
K-factor:
TMmax.:
Materials:
Density cal.:
Ser.No.:
TAG No.:
Order Code:
5,610,342
IP67
pnom =PS= 100bar
N12895
PROMASS F
10

Proline Promass 83 FOUNDATION Fieldbus Identification
Endress+Hauser 11
2.1.3 Nameplate for connections
a0002083
Fig. 4: Nameplate specifications for Proline transmitter (example)
1 Serial number
2 Possible configuration of current output
3 Possible configuration of relay contacts
4 Terminal assignment, cable for power supply: 85 to 260 V AC, 20 to 55 V AC, 16 to 62 V DC
Terminal No. 1: L1 for AC, L+ for DC
Terminal No. 2: N for AC, L- for DC
5 Signals present at inputs and outputs →Page 95 ff.;
Possible configuration and terminal assignment
6 Version of device software currently installed (incl. language group)
7 Installed communication type
8 Information on current communication software
9 Date of installation
10 Current updates to data specified in points 6 to 9
Communication:
Drivers:
Device SW:
ID XXXX (HEX)
XX.XX.XX (WEA)
XXXXXXXXXX
Date: DD. MMM. YYYY
Ex–works / ab Werk / réglages usine
26(+) / 27(-)
NC:
Observer manuel d'instruction
See operating manual
Betriebsanleitung beachten
26=FF+
27 = FF –
FOUNDATION Fieldbus
12345678912 Ser.No.:
24(+) / 25(-)
22(+) / 23(-)
20(+) / 21(-)
N/L-
PE
A:
NO:
P:
L1/L+
12
319475-00XX
X
active
passive
normally open contact
normally closed contact
Update 1 Update 2
2
3
1
4
5
6
7
8
9
10
Versorgung /
Tension d'alimentation
Supply /

Identification Proline Promass 83 FOUNDATION Fieldbus
12 Endress+Hauser
2.2 Certificates and approvals
The devices are designed in accordance with good engineering practice to meet state-of-the-art
safety requirements, have been tested, and left the factory in a condition in which they are safe to
operate. The devices comply with the applicable standards and regulations in accordance with
EN 61010-1 "Protection Measures for Electrical Equipment for Measurement, Control, Regulation
and Laboratory Procedures" and with the EMC requirements of EN 61326/A1.
The measuring system described in these Operating Instructions thus complies with the statutory
requirements of the EC Directives. Endress+Hauser confirms successful testing of the device by
affixing to it the CE mark.
The measuring system meets the EMC requirements of the Australian Communications and Media
Authority (ACMA).
2.3 FOUNDATION Fieldbus device certification
The flowmeter has passed all the test procedures implemented and has been certified and registered
by the Fieldbus FOUNDATION. The flowmeter thus meets all the requirements of the specifications
listed below:
• Certified to FOUNDATION fieldbus specification
• The flowmeter meets all the specifications of the FOUNDATION Fieldbus-H1.
• Interoperability Test Kit (ITK), revision 5.0: The device can also be operated in conjunction with
other-make certified devices.
• Physical Layer Conformance Test by Fieldbus Foundation
2.4 Registered trademarks
KALREZ®and VITON®
Registered trademarks of E.I. Du Pont de Nemours & Co., Wilmington, USA
TRI-CLAMP®
Registered trademark of Ladish & Co., Inc., Kenosha, USA
SWAGELOK®
Registered trademark of Swagelok & Co., Solon, USA
FOUNDATION™ Fieldbus
Registered trademark of the Fieldbus FOUNDATION, Austin, USA
HistoROM™, S-DAT®, T-DAT™, F-CHIP®, FieldCare®, ToF Tool - Fieldtool®Package,
Fieldcheck®, Applicator®
Registered or registration-pending trademarks of Endress+Hauser Flowtec AG, Reinach, CH

Proline Promass 83 FOUNDATION Fieldbus Installation
Endress+Hauser 13
3 Installation
3.1 Incoming acceptance, transport and storage
3.1.1 Incoming acceptance
On receipt of the goods, check the following points:
• Check the packaging and the contents for damage.
• Check the shipment, make sure nothing is missing and that the scope of supply matches your
order.
3.1.2 Transport
The following instructions apply to unpacking and to transporting the device to its final location:
• Transport the devices in the containers in which they are delivered.
• The covers or caps fitted to the process connections prevent mechanical damage to the sealing
faces and the ingress of foreign matter to the measuring tube during transportation and storage.
Consequently, do not remove these covers or caps until immediately before installation.
• Do not lift measuring devices of nominal diameters >DN 40 (>1½") by the transmitter housing
or the connection housing in the case of the remote version (Fig. 5). Use webbing slings slung
round the two process connections. Do not use chains, as they could damage the housing.
• In the case of the Promass M / DN 80 sensor, use only the lifting eyes on the flanges to lift the
assembly.
#Warning!
Risk of injury if the measuring device slips. The center of gravity of the assembled measuring device
might be higher than the points around which the slings are slung.
At all times, therefore, make sure that the device does not unexpectedly turn around its axis or slip.
a0004294
Fig. 5: Instructions for transporting sensors with >DN 40 (>1½")

Installation Proline Promass 83 FOUNDATION Fieldbus
14 Endress+Hauser
3.1.3 Storage
Note the following points:
• Pack the measuring device in such a way as to protect it reliably against impact for storage (and
transportation). The original packaging provides optimum protection.
• The permitted storage temperature is: –40 to +80 °C (–40 °F to +176 °F),
preferably +20 °C (+68 °F).
• Do not remove the protective covers or caps on the process connections until you are ready to
install the device.
• The measuring device must be protected against direct sunlight during storage in order to avoid
unacceptably high surface temperatures.
3.2 Installation conditions
Note the following points:
• No special measures such as supports are necessary. External forces are absorbed by the
construction of the instrument, for example the secondary containment.
• The high oscillation frequency of the measuring tubes ensures that the correct operation of the
measuring system is not influenced by pipe vibrations.
• No special precautions need to be taken for fittings which create turbulence (valves, elbows,
T-pieces, etc.), as long as no cavitation occurs.
• For mechanical reasons and in order to protect the pipe, it is advisable to support heavy sensors.
3.2.1 Dimensions
All the dimensions and lengths of the sensor and transmitter are provided in the separate
documentation "Technical Information".
3.2.2 Mounting location
Entrained gas bubbles in the measuring tube can result in an increase in measuring errors.
Avoid the following locations:
• Highest point of a pipeline. Risk of air accumulating.
• Directly upstream of a free pipe outlet in a vertical pipeline.
a0003605
Fig. 6: Mounting location

Proline Promass 83 FOUNDATION Fieldbus Installation
Endress+Hauser 15
The proposed configuration in the following diagram, however, permits installation in a vertical
pipeline. Pipe restrictors or the use of an orifice plate with a smaller cross-section than the nominal
diameter prevent the sensor from running empty during measurement.
a0003597
Fig. 7: Installation in a vertical pipe (e.g. for batching applications)
1 = Supply tank , 2 = Sensor, 3 = Orifice plate, pipe restrictor (see Table), 4 = Valve, 5 = Batching container
System pressure
It is important to ensure that cavitation does not occur, because it would influence the oscillation
of the measuring tube. No special measures need to be taken for fluids which have properties similar
to water under normal conditions.
In the case of liquids with a low boiling point (hydrocarbons, solvents, liquefied gases) or in suction
lines, it is important to ensure that pressure does not drop below the vapor pressure and that the
liquid does not start to boil. It is also important to ensure that the gases that occur naturally in many
liquids do not outgas. Such effects can be prevented when system pressure is sufficiently high.
For this reason, the following installation locations are preferred:
• Downstream from pumps (no danger of vacuum)
• At the lowest point in a vertical pipe.
1
2
3
4
5
DN
∅Orifice plate, pipe
restrictor
DN
∅Orifice plate, pipe
restrictor
mm inch mm inch
1 1/24" 0.8 0.03 40 1 ½" 22 0.87
2 1/12" 1.5 0.06 40 FB 1 ½" 35 1.38
4 1/8" 3.0 0.12 50 2" 28 1.10
8 3/8" 6 0.24 50 FB 2" 54 2.00
15 1/2" 10 0.40 80 3" 50 2.00
15 FB 1/2" 15 0.60 100 4" 65 2.60
25 1" 14 0.55 150 6" 90 3.54
25 FB 1" 24 0.95 250 10" 150 5.91
FB = Full bore versions of Promass I

Installation Proline Promass 83 FOUNDATION Fieldbus
16 Endress+Hauser
3.2.3 Orientation
Make sure that the direction of the arrow on the nameplate of the sensor matches the direction of
flow (direction in which the fluid flows through the pipe).
Orientation of Promass A
Vertical:
Recommended orientation with upward direction of flow. When fluid is not flowing, entrained
solids will sink down and gases will rise away from the measuring tube. The measuring tubes can
be completely drained and protected against solids buildup.
Horizontal:
When installation is correct the transmitter housing is above or below the pipe. This arrangement
means that no gas or solid deposits can accumulate in the curved measuring tube (single-tube
system).
Do not install the sensor in such a way that it is suspended in the pipe, in other words without
support or attachment. This is to avoid excessive strain at the process connection. The base plate of
the sensor housing is designed for mounting on a tabletop, wall or post.
a0003606
Fig. 8: Vertical and horizontal orientation (Promass A)

Proline Promass 83 FOUNDATION Fieldbus Installation
Endress+Hauser 17
Orientation of Promass F, M, E, H, I, S, P
Make sure that the direction of the arrow on the nameplate of the sensor matches the direction of
flow (direction in which the fluid flows through the pipe).
Vertical:
Recommended orientation with upward direction of flow (View V). When fluid is not flowing,
entrained solids will sink down and gases will rise away from the measuring tube. The measuring
tubes can be completely drained and protected against solids buildup.
Horizontal (Promass F, M, E):
The measuring tubes of Promass F, M and E must be horizontal and beside each other. When
installation is correct the transmitter housing is above or below the pipe (View H1/H2). Always
avoid having the transmitter housing in the same horizontal plane as the pipe.
Horizontal (Promass H, I, S, P):
Promass H and Promass I can be installed in any orientation in a horizontal pipe run.
In order to ensure that the maximum permissible ambient temperature for the transmitter is not
exceeded (–20 to +60 °C (–4 to +140 °F), optionally –40 to +60 °C (–40 to +140 °F)), we
recommend the following orientations:
m= For fluids with very high temperatures > 200 °C (392 °F), we recommend the horizontal
orientation with the transmitter head pointing downwards (Fig. H2) or the vertical orientation
(Fig. V).
n= For fluids with low temperatures, we recommend the horizontal orientation with the
transmitter head pointing upwards (Fig. H1) or the vertical orientation (Fig. V).
Promass F, M, E, H, I, S, P Standard, compact Promass F, M, E, H, I, S, P Standard, remote Promass F High-temperature, compact Promass F High-temperature, remote
Fig. V:
Vertical orientation
a0004572
ÃÃ ÃÃ ÃÃ ÃÃ
Fig. H1:
Horizontal orientation
Transmitter head up
a0004576
ÃÃ ÃÃ
✘
TM > 200 °C
(392 °F)
m
Ã
TM > 200 °C
(392 °F)
m
Fig. H2:
Horizontal orientation
Transmitter head down
a0004580
ÃÃ
n
ÃÃ
n
ÃÃ
n
ÃÃ
n
ÃÃ = Recommended orientation
Ã= Orientation recommended in certain situations
✘= Impermissible orientation

Installation Proline Promass 83 FOUNDATION Fieldbus
18 Endress+Hauser
Special installation instructions for Promass F, E, H, S and P
"Caution!
If the measuring tube is curved and the unit is installed horizontally, the position of the sensor has
to be aligned with the fluid properties!
a0004581
Fig. 9: Horizontal installation for sensors with a curved measuring tube
1 Not suitable for fluids with entrained solids. Risk of solids accumulating.
2 Not suitable for outgassing fluids. Risk of air accumulating.
3.2.4 Heating
Some fluids require suitable measures to avoid loss of heat at the sensor. Heating can be electric,
e.g. with heated elements, or by means of hot water or steam pipes made of copper.
"Caution!
• Risk of electronics overheating! Consequently, make sure that the adapter between sensor and
transmitter and the connection housing of the remote version always remain free of insulating
material. Note that a certain orientation might be required, depending on the fluid temperature.
→Page 16
• With a fluid temperature between 200 and 350 °C (392 to 662 °F), heating is not permitted for
the compact version of the high-temperature version.
• When using electrical heat tracing whose heat is regulated using phase control or by pulse packs,
it cannot be ruled out that the measured values are influenced by magnetic fields which may
occur, (i.e. at values greater than those permitted by the EC standard (Sinus 30 A/m)). In such
cases, the sensor must be magnetically shielded (except for Promass M).
The secondary containment can be shielded with tin plates or electric sheets without privileged
direction (e.g. V330-35A) with the following properties:
– Relative magnetic permeability μr≥300
– Plate thickness d ≥0.35 mm (0.0011")
• Information on permissible temperature ranges →Page 108
Special heating jackets which can be ordered as accessories from Endress+Hauser are available for
the sensors.
12

Proline Promass 83 FOUNDATION Fieldbus Installation
Endress+Hauser 19
3.2.5 Thermal insulation
Some fluids require suitable measures to avoid loss of heat at the sensor. A wide range of materials
can be used to provide the required thermal insulation.
a0004614-ae
Fig. 10: In the case of the Promass F high-temperature version, a maximum insulation thickness of 60 mm (2.4") must
be observed in the area of the electronics/neck.
If the device is installed horizontally (with transmitter head pointing upwards), an insulation
thickness of min. 10 mm (0.4") is recommended to reduce convection. The maximum insulation
thickness of 60 mm (2.4") must not be exceeded.
3.2.6 Inlet and outlet runs
There are no installation requirements regarding inlet and outlet runs. If possible, install the sensor
well clear of fittings such as valves, T-pieces, elbows, etc.
3.2.7 Vibrations
The high oscillation frequency of the measuring tubes ensures that the correct operation of the
measuring system is not influenced by pipe vibrations. Consequently, the sensors require no special
measures for attachment.
3.2.8 Limiting flow
Information on limiting flow is provided under "Measuring range" in the technical data section.
→Page 95
Esc
E
-
+
max. 60 (2.4)
max. 60 (2.4)
mm (inch)

Installation Proline Promass 83 FOUNDATION Fieldbus
20 Endress+Hauser
3.3 Installation instructions
3.3.1 Turning the transmitter housing
Turning the aluminum field housing
#Warning!
The turning mechanism in devices with EEx d/de or FM/CSA Cl. I Div. 1 classification is not the
same as that described here. The procedure for turning these housings is described in the Ex-specific
documentation.
1. Loosen the two securing screws.
2. Turn the bayonet catch as far as it will go.
3. Carefully lift the transmitter housing as far as it will go.
4. Turn the transmitter housing to the desired position (max. 2 x 90° in either direction).
5. Lower the housing into position and reengage the bayonet catch.
6. Retighten the two securing screws.
a0004302
Fig. 11: Turning the transmitter housing (aluminum field housing)
Turning the stainless steel field housing
1. Loosen the two securing screws.
2. Carefully lift the transmitter housing as far as it will go.
3. Turn the transmitter housing to the desired position (max. 2 x 90° in either direction).
4. Lower the housing into position.
5. Retighten the two securing screws.
a0004303
Fig. 12: Turning the transmitter housing (stainless steel field housing)
3
5
6
1
24
12
3
4
5