Endress+Hauser RID14 Technical specifications

Products Solutions Services
Brief Operating Instructions
RID14
8-channel field indicator
with FOUNDATION Fieldbus™
These Brief Operating Instructions are not a substitute for the
Operating Instructions pertaining to the device.
Detailed information is provided in the Operating Instructions
and other documentation.
Available for all device versions via:
• Internet: www.endress.com/deviceviewer
• Smartphone/tablet: Endress+Hauser Operations app
KA00281R/09/EN/15.22-00
71593373
2022-07-28

RID14
2 Endress+Hauser
Order code:
Ext. ord. cd.:
Ser. no.:
www.endress.com/deviceviewer Endress+Hauser
Operations App
XXXXXXXXXXXX
XXXXX-XXXXXX
XXX.XXXX.XX
Serial number
1.
3.
2.
A0023555

RID14 Table of contents
Endress+Hauser 3
Table of contents
1 About this document .............................................................. 3
1.1 Symbols ............................................................................. 3
2 Safety instructions ................................................................ 5
2.1 Requirements for personnel .............................................................. 5
2.2 Designated use ........................................................................ 6
2.3 Workplace safety ...................................................................... 6
2.4 Operational safety ......................................................................6
2.5 Product safety ......................................................................... 6
3 Identification ..................................................................... 6
3.1 Device designation ..................................................................... 6
3.2 Scope of delivery ....................................................................... 7
3.3 Certificates and approvals ................................................................ 7
4 Installation ....................................................................... 8
4.1 Incoming acceptance, transport, storage ..................................................... 8
4.2 Installation conditions ................................................................... 8
4.3 Installation instructions ..................................................................9
4.4 Post-installation check ................................................................. 11
5 Wiring ........................................................................... 11
5.1 Connecting the cable to the field indicator ................................................... 12
5.2 Connection to FOUNDATION Fieldbus™ ..................................................... 13
5.3 Degree of protection ................................................................... 15
5.4 Post-connection check ..................................................................16
6 Operating the field indicator ..................................................... 16
6.1 Quick operation guide .................................................................. 16
6.2 Display and operating elements ........................................................... 18
6.3 Configuration of the field indicator ........................................................ 19
6.4 Hardware settings ..................................................................... 19
6.5 Device configuration ................................................................... 20
1 About this document
1.1 Symbols
1.1.1 Safety symbols
DANGER
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.
WARNING
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.
CAUTION
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.

About this document RID14
4 Endress+Hauser
NOTICE
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.1.2 Electrical symbols
Symbol Meaning Symbol Meaning
Direct current Alternating current
Direct current and alternating current Ground connection
A grounded terminal which, as far as
the operator is concerned, is grounded
via a grounding system.
Symbol Meaning
Potential equalization connection (PE: protective earth)
Ground terminals that must be connected to ground prior to establishing any other connections.
The ground terminals are located on the interior and exterior of the device:
• Interior ground terminal: potential equalization is connected to the supply network.
• Exterior ground terminal: device is connected to the plant grounding system.
1.1.3 Symbols for certain types of information
Symbol Meaning Symbol Meaning
Permitted
Procedures, processes or actions that
are permitted.
Preferred
Procedures, processes or actions that
are preferred.
Forbidden
Procedures, processes or actions that
are forbidden.
Tip
Indicates additional information.
Reference to documentation
A
Reference to page
Reference to graphic
1.
,
2.
,
3.
… Series of steps
Result of a step Visual inspection

RID14 Safety instructions
Endress+Hauser 5
1.1.4 Symbols in graphics
Symbol Meaning Symbol Meaning
1, 2, 3,... Item numbers
1.
,
2.
,
3.
… Series of steps
A, B, C, ... Views A-A, B-B, C-C, ... Sections
-
Hazardous area
.
Safe area (non-hazardous area)
1.1.5 Tool symbols
Symbol Meaning
A0011220
Flat blade screwdriver
A0011221
Allen key
A0011222
Open-ended wrench
A0013442
Torx screwdriver
2 Safety instructions
2.1 Requirements for personnel
The personnel must fulfill the following requirements for its tasks:
‣Trained, qualified specialists must have a relevant qualification for this specific function
and task.
‣Are authorized by the plant owner/operator.
‣Are familiar with federal/national regulations.
‣Before starting work, read and understand the instructions in the manual and
supplementary documentation as well as the certificates (depending on the application).
‣Follow instructions and comply with basic conditions.

Identification RID14
6 Endress+Hauser
2.2 Designated use
• The device is a field indicator designed for connection to a fieldbus.
• The device is designed for installation in the field.
• The manufacturer accepts no liability for damages resulting from incorrect use or use other
than that designated.
• Safe operation is only guaranteed if operators comply strictly with the Operating
Instructions.
• Only operate the device in the designated temperature range.
2.3 Workplace safety
For work on and with the device:
‣Wear the required personal protective equipment according to federal/national
regulations.
2.4 Operational safety
Risk of injury.
‣Operate the device in proper technical condition and fail-safe condition only.
‣The operator is responsible for interference-free operation of the device.
2.5 Product safety
This measuring device is designed in accordance with good engineering practice to meet state-
of-the-art safety requirements, has been tested, and left the factory in a condition in which it
is safe to operate.
It meets general safety standards and legal requirements. It also complies with the EC
directives listed in the device-specific EC Declaration of Conformity. Endress+Hauser confirms
this by affixing the CE mark to the device.
3 Identification
3.1 Device designation
3.1.1 Nameplate
The right device?
Compare the order code on the nameplate of the device to that on the delivery papers.

RID14 Identification
Endress+Hauser 7
Made in Germany 2013
D-87484 Nesselwang
Order code: RID14-XXXX/X
Ser. no.: XXXXXXXXXXX
Ext. ord. cd.: RID14-XXXXX
9 - 32 V
Ta = -40 ...+55/70/80°C
FW: 1.00.00-[1...1] DevRev: X
4
IP66/67 Type 4X
RID14
1
2
3
4
5
6
A0012565
 1 Nameplate of the field indicator (example)
1 Designation, order code and serial number of the device
2 Power supply
3 Ambient temperature range
4 Firmware version and device revision
5 Degree of protection and type of approval
6 Approvals
3.2 Scope of delivery
The scope of delivery of the field indicator comprises:
• Field indicator
• Brief Operating Instructions as hard copy
• ATEX - safety instructions for using a device approved for hazardous areas, optional
• Optional accessories (e.g. pipe mounting bracket), see 'Accessories' section in the Operating
instructions.
3.3 Certificates and approvals
3.3.1 CE mark
The measuring system meets the legal requirements of the applicable EC guidelines. These are
listed in the corresponding EC Declaration of Conformity together with the standards applied.
The manufacturer confirms successful testing of the device by affixing to it the CE mark.
3.3.2 UL approval
UL recognized component (see www.ul.com/database, search for Keyword "E225237")
3.3.3 EAC mark
The product meets the legal requirements of the EEU guidelines. The manufacturer confirms
the successful testing of the product by affixing the EAC mark.

Installation RID14
8 Endress+Hauser
3.3.4 CSA
CSA General Purpose
3.3.5 Certification Foundation Fieldbus™
The field indicator has successfully passed all the tests and is certified and registered by the
Fieldbus Foundation. The device meets all the requirements of the following specifications:
• Certified in accordance with FOUNDATION Fieldbus™ specification
• FOUNDATION Fieldbus™ H1
• Interoperability Test Kit (ITK), revision status 6.1.2 (device certification number available on
request): the device may also be operated using certified devices from other manufacturers
• Physical Layer Conformance Test of the Fieldbus FOUNDATION™ (FF-830 FS 2.0)
3.3.6 Registered trademarks
FOUNDATION Fieldbus™
Registered trademark of the Fieldbus Foundation Austin, Texas, USA
4 Installation
4.1 Incoming acceptance, transport, storage
The permitted ambient and storage conditions must be observed. The precise specifications
can be found in Section "Technical data" in the Operating Instructions.
4.1.1 Incoming acceptance
On receipt of the goods, check the following points:
• Are the packaging or contents damaged?
• Is anything missing from the delivery? Compare the scope of delivery with the information
you specified in the order. See also section "Scope of delivery" →  7.
4.1.2 Transportation and storage
Note the following points:
• Pack the device so that is protected against impact for storage and transportation. The
original packaging provides optimum protection.
• The permitted storage temperature range is –40 to +80 °C (–40 to +176 °F); it is possible to
store the device in the limit temperature ranges for a limited period (maximum 48 hours).
4.2 Installation conditions
The process indicator is designed to be used in the field.
The orientation is determined by the readability of the display.
Operational temperature range:
–40 to +80 °C (–40 to +176 °F)

RID14 Installation
Endress+Hauser 9
NOTICE
Shorter display operating life at higher temperatures
‣Where possible do not operate the device in the higher temperature range.
The display can react slowly at temperatures < –20 °C (–4 °F).
The readability of the display is no longer guaranteed at temperatures < –30 °C (–22 °F).
4.2.1 Dimensions
132 (5.2)
135 (5.3)
112 (4.4)
166 (6.5)
106 (4.2) 121 (4.8)
121 (4.8)
!6.4
(0.25)
A0011152
 2 Dimension of the filed indicator in mm (in)
4.2.2 Installation location
Information on conditions that must be present at the installation location to mount the
device correctly can be found in Section 'Technical data' in the Operating Instructions. These
include the ambient temperature, degree of protection, climate class etc.
4.3 Installation instructions
The device can be mounted directly on the wall →  10. A mounting bracket is available for
mounting on a pipe →  4,  11.
The backlit display can be mounted in 4 different positions →  10.

Installation RID14
10 Endress+Hauser
4.3.1 Turning the display
Pos. 1
2
3
1
4
1.
2.
90°
90° 90°
Pos. 2 Pos. 3 Pos. 4
3.
A0023724
 3 Field indicator, 4 display positions, can be fitted in 90° stages
The display unit can be turned in 90 ° stages.
1. First remove the cover clamp (1) and the housing cover (2).
2. Then disconnect the display (3) from the electronics unit (4).
3. Turn the display to the desired position and then fit it onto the electronics unit.
4.3.2 Mounting directly on the wall
Proceed as follows to mount the device directly on the wall:
1. Drill 2 holes
2. Fit the device on the wall with 2 screws (⌀5 mm (0.2 in)).
4.3.3 Pipe mounting
The mounting bracket is suitable for pipes with a diameter between 1.5" to 3.3".
The additional mounting plate must be used for pipes with a diameter between 1.5" to 2.2".
The mounting plate is not needed for pipes with a diameter between 2.2" to 3.3".
Proceed as follows to mount the device on a pipe: