Endress+Hauser Proline Promag 55 User manual

BA00124D/06/EN/13.11
71130401
Valid as of version
PROFIBUS DP
V 3.06.XX (Device software)
PROFIBUS PA
V 3.06.XX (Device software)
Operating Instructions
Proline Promag 55
PROFIBUS DP/PA
Electromagnetic Flow Measuring System
8

Proline Promag 55 PROFIBUS DP/PA Table of contents
Endress+Hauser 3
Table of contents
1 Safety instructions . . . . . . . . . . . . . . . . 5
1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Installation, commissioning, operation . . . . . . . . . . . 5
1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.4 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.5 Notes on safety conventions and icons . . . . . . . . . . . 6
2 Identification . . . . . . . . . . . . . . . . . . . . 7
2.1 Device designation . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1.1 Nameplate of the transmitter . . . . . . . . . . . . 7
2.1.2 Nameplate of the sensor . . . . . . . . . . . . . . . 8
2.1.3 Nameplate for connections . . . . . . . . . . . . . 9
2.2 Certificates and approvals . . . . . . . . . . . . . . . . . . . 10
2.3 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . 10
3 Installation . . . . . . . . . . . . . . . . . . . . . 11
3.1 Incoming acceptance, transport and storage . . . . . . 11
3.1.1 Incoming acceptance . . . . . . . . . . . . . . . . . 11
3.1.2 Transport . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1.3 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2 Installation conditions . . . . . . . . . . . . . . . . . . . . . . 13
3.2.1 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2.2 Mounting location . . . . . . . . . . . . . . . . . . . 13
3.2.3 Orientation . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2.4 Inlet and outlet runs . . . . . . . . . . . . . . . . . 16
3.2.5 Vibrations . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.2.6 Foundations, supports . . . . . . . . . . . . . . . . 17
3.2.7 Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.2.8 Nominal diameter and flow rate
Promag S and Promag H . . . . . . . . . . . . . . 18
3.2.9 Length of connecting cable . . . . . . . . . . . . 21
3.3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.3.1 Installing the Promag S sensor . . . . . . . . . . 22
3.3.2 Installing the Promag H sensor . . . . . . . . . . 28
3.3.3 Turning the transmitter housing . . . . . . . . 31
3.3.4 Turning the local display . . . . . . . . . . . . . . 32
3.3.5 Installing the wall-mount housing . . . . . . . 33
3.4 Post-installation check . . . . . . . . . . . . . . . . . . . . . . 35
4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . 36
4.1 PROFIBUS cable specifications . . . . . . . . . . . . . . . . 36
4.1.1 PROFIBUS DP cable specification . . . . . . . 36
4.1.2 PROFIBUS PA cable specifications . . . . . . . 37
4.1.3 Shielding and grounding . . . . . . . . . . . . . . 39
4.2 Connecting the remote version . . . . . . . . . . . . . . . 40
4.2.1 Connecting the sensor . . . . . . . . . . . . . . . . 40
4.2.2 Cable specifications . . . . . . . . . . . . . . . . . . 44
4.3 Connecting the measuring unit . . . . . . . . . . . . . . . 45
4.3.1 Terminal assignment . . . . . . . . . . . . . . . . . 45
4.3.2 Connecting the transmitter . . . . . . . . . . . . 46
4.3.3 PROFIBUS DP connection diagram . . . . . . 47
4.3.4 PROFIBUS PA connection diagram . . . . . . 49
4.4 Potential equalization . . . . . . . . . . . . . . . . . . . . . . . 52
4.4.1 Potential equalization, Promag S . . . . . . . . 52
4.4.2 Potential equalization, Promag H . . . . . . . . 52
4.4.3 Connection examples for
potential equalization . . . . . . . . . . . . . . . . . 52
4.5 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . 54
4.6 Post-connection check . . . . . . . . . . . . . . . . . . . . . . 55
5 Operation . . . . . . . . . . . . . . . . . . . . . . 56
5.1 Quick operation guide . . . . . . . . . . . . . . . . . . . . . . 56
5.2 Local display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
5.2.1 Display and operating elements . . . . . . . . . 57
5.2.2 Display (operating mode) . . . . . . . . . . . . . . 58
5.2.3 Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
5.3 Brief operating instructions for the function matrix . 60
5.3.1 General notes . . . . . . . . . . . . . . . . . . . . . . 61
5.3.2 Enabling the programming mode . . . . . . . . 61
5.3.3 Disabling the programming mode . . . . . . . . 61
5.4 Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
5.4.1 Type of error . . . . . . . . . . . . . . . . . . . . . . . 62
5.4.2 Error message type . . . . . . . . . . . . . . . . . . . 62
5.5 Operating options . . . . . . . . . . . . . . . . . . . . . . . . . 63
5.5.1 Operating program "FieldCare" . . . . . . . . . . 63
5.5.2 Operating program "SIMATIC PDM"
(Siemens) . . . . . . . . . . . . . . . . . . . . . . . . . 63
5.5.3 Device description files for
operating programs . . . . . . . . . . . . . . . . . . 64
5.6 Hardware PROFIBUS DP settings . . . . . . . . . . . . . . 66
5.6.1 Configuring the write protection . . . . . . . . 66
5.6.2 Configuring the device address . . . . . . . . . . 67
5.6.3 Configuring the terminating resistors . . . . . 68
5.6.4 Current output configuration . . . . . . . . . . . 69
5.6.5 Relay output configuration . . . . . . . . . . . . . 70
5.7 PROFIBUS PA hardware settings . . . . . . . . . . . . . . 71
5.7.1 Configuring the write protection . . . . . . . . 71
5.7.2 Configuring the device address . . . . . . . . . . 72
6 Commissioning . . . . . . . . . . . . . . . . . . 73
6.1 Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
6.2 Switching on the measuring device . . . . . . . . . . . . 73
6.3 Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
6.3.1 Quick Setup "Commissioning" . . . . . . . . . . 74
6.3.2 Quick Setup "Pulsating Flow" . . . . . . . . . . . 76
6.3.3 Quick Setup "Communication" . . . . . . . . . . 79
6.3.4 Data backup/transmission . . . . . . . . . . . . . 81
6.4 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
6.4.1 Measuring solids content flow . . . . . . . . . . 82
6.4.2 Advanced diagnostic functions . . . . . . . . . . 84
6.5 Commissioning the PROFIBUS interface . . . . . . . . . 86
6.5.1 PROFIBUS DP commissioning . . . . . . . . . . 86
6.5.2 PROFIBUS PA commissioning . . . . . . . . . . 89
6.6 PROFIBUS DP/PA system integration . . . . . . . . . . 92
6.6.1 Device master file (GSD file) . . . . . . . . . . . 92
6.6.2 Selecting the GSD file in the
measuring device . . . . . . . . . . . . . . . . . . . . 94

Proline Promag 55 PROFIBUS DP/PA Table of contents
4Endress+Hauser
6.6.3 Compatibility to the previous model Promag 35
(Profile Version 2.0) . . . . . . . . . . . . . . . . . . 95
6.6.4 Maximum number of writes . . . . . . . . . . . 95
6.7 PROFIBUS DP cyclic data transmission . . . . . . . . . 96
6.7.1 Block model . . . . . . . . . . . . . . . . . . . . . . . 96
6.7.2 Modules for cyclic data transmission . . . . . 96
6.7.3 Description of the modules . . . . . . . . . . . . 97
6.7.4 Configuration examples with Simatic S7 HW-
Konfig . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
6.8 PROFIBUS PA cyclic data transmission . . . . . . . . . 106
6.8.1 Block model . . . . . . . . . . . . . . . . . . . . . . 106
6.8.2 Modules for cyclic data transmission . . . . 106
6.8.3 Description of the modules . . . . . . . . . . . 107
6.8.4 Configuration examples with
Simatic S7 HW-Konfig . . . . . . . . . . . . . . . 114
6.9 PROFIBUS DP/PA acyclic data transmission . . . . 116
6.9.1 Master class 2 acyclic (MS2AC) . . . . . . . . 116
6.9.2 Master class 1 acyclic (MS1AC) . . . . . . . . 116
6.10 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
6.10.1 Empty-pipe/full-pipe adjustment . . . . . . . 117
6.11 Data storage devices . . . . . . . . . . . . . . . . . . . . . . 118
6.11.1 HistoROM/S-DAT (sensor-DAT) . . . . . . . 118
6.11.2 HistoROM/T-DAT (transmitter-DAT) . . . 118
6.11.3 F-CHIP (Function chip) . . . . . . . . . . . . . . 118
7 Maintenance . . . . . . . . . . . . . . . . . . . 119
7.1 Exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . 119
7.2 Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
8 Accessories . . . . . . . . . . . . . . . . . . . . 120
8.1 Device-specific accessories . . . . . . . . . . . . . . . . . . 120
8.2 Measuring principle-specific accessories . . . . . . . . 120
8.3 Communication-specific accessories . . . . . . . . . . . 121
9 Troubleshooting . . . . . . . . . . . . . . . . 122
9.1 Troubleshooting instructions . . . . . . . . . . . . . . . . 122
9.2 System error messages . . . . . . . . . . . . . . . . . . . . . 124
9.2.1 Displaying the device status on
PROFIBUS DP/PA . . . . . . . . . . . . . . . . . . 124
9.2.2 List of system error messages . . . . . . . . . . 125
9.3 Process error messages . . . . . . . . . . . . . . . . . . . . . 132
9.3.1 Displaying the device status on
PROFIBUS DP/PA . . . . . . . . . . . . . . . . . . 132
9.3.2 List of process error messages . . . . . . . . . . 132
9.4 Process errors without messages . . . . . . . . . . . . . 133
9.5 Failsafe mode of outputs . . . . . . . . . . . . . . . . . . . 134
9.6 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
9.6.1 PROFIBUS DP . . . . . . . . . . . . . . . . . . . . . 135
9.6.2 PROFIBUS PA . . . . . . . . . . . . . . . . . . . . . 136
9.6.3 Removing and installing
printed circuit boards . . . . . . . . . . . . . . . . 137
9.6.4 Replacing the device fuse . . . . . . . . . . . . . 139
9.7 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
9.8 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
9.9 Software history . . . . . . . . . . . . . . . . . . . . . . . . . 140
10 Technical data . . . . . . . . . . . . . . . . . . 141
10.1 Technical data at a glance . . . . . . . . . . . . . . . . . . 141
10.1.1 Applications . . . . . . . . . . . . . . . . . . . . . . 141
10.1.2 Function and system design . . . . . . . . . . 141
10.1.3 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
10.1.4 Output . . . . . . . . . . . . . . . . . . . . . . . . . . 142
10.1.5 Power supply . . . . . . . . . . . . . . . . . . . . . 143
10.1.6 Measuring accuracy . . . . . . . . . . . . . . . . 144
10.1.7 Operating conditions: Installation . . . . . . 145
10.1.8 Operating conditions: Environment . . . . . 145
10.1.9 Operating conditions: Process . . . . . . . . . 146
10.1.10 Mechanical construction . . . . . . . . . . . . 150
10.1.11 Human interface . . . . . . . . . . . . . . . . . . 154
10.1.12 Certificates and approvals . . . . . . . . . . . . 155
10.1.13 Ordering information . . . . . . . . . . . . . . . 156
10.1.14 Accessories . . . . . . . . . . . . . . . . . . . . . . 156
10.1.15 Documentation . . . . . . . . . . . . . . . . . . . 156
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157

Proline Promag 55 PROFIBUS DP/PA Safety instructions
Endress+Hauser 5
1 Safety instructions
1.1 Designated use
The measuring device described in these Operating Instructions is to be used only for measuring the
flow rate of conductive liquids in closed pipes.
All fluids (incl. demineralized water) can be metered, provided they have a minimum conductivity
of 5 μS/cm for example:
• acids, alkalis, pastes, paps, pulps, black liquor, green liquor
• drinking water, wastewater, sewage sludge
• milk, beer, wine, mineral water, yoghurt, molasses, fruit mash
• cement, laitance, ore slurry (containing sand or stone), mud, silt
The operational safety of the measuring devices cannot be guaranteed if the system is used
incorrectly or used for purposes other than those intended. The manufacturer accepts no liability for
damages being produced from this.
1.2 Installation, commissioning, operation
Note the following points:
• Installation, connection to the electricity supply, commissioning and maintenance of the device
must be carried out by trained, skilled personnel authorized to perform such work by the facility's
owner-operator. The skilled personnel must have read and understood these Operating
Instructions and follow the instructions they contain.
• The device must be operated by persons authorized and trained by the facility's owner-operator.
Strict compliance with the instructions in the Operating Instructions is mandatory.
• Endress+Hauser is willing to assist in clarifying the chemical resistance properties of parts wetted
by special fluids, including fluids used for cleaning. However, small changes in temperature,
concentration or in the degree of contamination in the process can result in changes of the
chemical resistance properties. Therefore, Endress+Hauser can not guarantee or accept liability
for the chemical resistance properties of the fluid wetted materials in a specific application. The
user is responsible for the choice of fluid wetted materials in regards to their in-process resistance
to corrosion.
• If welding work is performed on the piping system, do not ground the welding appliance through
the flowmeter.
• The installer must ensure that the measuring system is correctly wired in accordance with the
wiring diagrams. The transmitter must be grounded, except in cases where special protective
measures have been taken (e.g. galvanically isolated power supply SELV
or PELV).
• Always note the regulations applicable in your country to the operation, maintenance and repair
of electrical devices. Special instructions relating to the device can be found in the relevant
sections of the documentation.
• The Promag 55 flow measuring device can also measure extremely abrasive fluids, e.g. ore slurry,
cement etc. To protect the measuring tube lining from excessive abrasion, the use of additional
liner protection plates is recommended in such cases.

Safety instructions Proline Promag 55 PROFIBUS DP/PA
6Endress+Hauser
1.3 Operational safety
Note the following points:
• Measuring systems for use in hazardous environments are accompanied by separate
"Ex documentation", which is an integral part of these Operating Instructions. Strict compliance
with the installation instructions and ratings as stated in this supplementary documentation is
mandatory. The symbol on the front of this supplementary Ex documentation indicates the
approval and the certification body (e.g. 0Europe, 2USA, 1Canada).
• The measuring device meets the general safety requirements according to EN 61010-1 and the
EMC requirements according to IEC/EN 61326 in addition to the NAMUR recommendations
NE 21, NE 43 and NE 53.
• Depending on the application, the seals of the process connections of the Promag H sensor require
periodic replacement.
• Due to the power turnover in the electronic components, the heating of the outer housing
surfaces is max. 10 K. When hot media are passed through the measuring tube, the surface
temperature of the housing increases. With regard to the sensor, in particular, you should expect
temperatures that can be close to the temperature of the medium. If the temperature of the
medium is high, ensure staff are protected against burns and scalds.
• The manufacturer reserves the right to modify technical data without prior notice. Your
Endress+Hauser distributor will supply you with current information and updates to these
Operating Instructions.
1.4 Return
• Do not return a measuring device if you are not absolutely certain that all traces of hazardous
substances have been removed, e.g. substances which have penetrated crevices or diffused
through plastic.
• Costs incurred for waste disposal and injury (burns, etc.) due to inadequate cleaning will be
charged to the owner-operator.
1.5 Notes on safety conventions and icons
The devices are designed and tested to meet state-of-the-art safety requirements, and have left the
factory in a condition in which they are safe to operate. The devices comply with the applicable
standards and regulations in accordance with EN 61010-1 "Protection Measures for Electrical
Equipment for Measurement, Control, Regulation and Laboratory Procedures". The devices can,
however, be a source of danger if used incorrectly or for other than the designated use.
Consequently, always pay particular attention to the safety instructions indicated in this Operating
Manual by the following icons:
#Warning!
"Warning" indicates an action or procedure which, if not performed correctly, can result in injury
or a safety hazard. Comply strictly with the instructions and proceed with care.
"Caution!
"Caution" indicates an action or procedure which, if not performed correctly, can result in incorrect
operation or destruction of the device. Comply strictly with the instructions.
!Note!
"Note" indicates an action or procedure which, if not performed correctly, can have an indirect
effect on operation or trigger an unexpected response on the part of the device.

Proline Promag 55 PROFIBUS DP/PA Identification
Endress+Hauser 7
2 Identification
2.1 Device designation
The flow measuring system consists of the following components:
• Promag 55 transmitter
• Promag S and Promag H sensor
Two versions are available:
• Compact version: Transmitter and sensor form a single mechanical unit.
• Remote version: Transmitter and sensor are installed separately.
2.1.1 Nameplate of the transmitter
A0006108
Fig. 1: Nameplate specifications for the "Promag 55" transmitter (example)
1 Order code/serial number: See the specifications on the order confirmation for the meanings of the individual
letters and digits
2 Power supply/frequency/Power consumption
3 Additional functions and software
4 Available inputs and outputs
5 Reserved for additional information on special products
6 Observe device documentation
7 Reserved for certificates, approvals and for additional information on device version
8 Degree of protection
9 Permitted ambient temperature range
PROMAG 55
–20°C (–4°F) <Tamb<+50°C (+122°F)
IP67 / NEMA/Type 4X Order Code:
Ser.No.:
TAG No.:
55S1H-XXXXXXXXXXXX
12345678901
ABCDEFGHJKLMNPQRST
20-260VAC / 20-64VDC
50-60Hz
PROFIBUS DP (Profile 3.0)
45VA/19W
i
EPD/MSU
B
P
U S
R O IF
R
1
2
3
4
5
6
7
8
9
N12895

Identification Proline Promag 55 PROFIBUS DP/PA
8Endress+Hauser
2.1.2 Nameplate of the sensor
A0006109
Fig. 2: Nameplate specifications for the "Promag" sensor (example)
1 Order code/serial number: See the specifications on the order confirmation for the meanings of the individual
letters and digits
2 Calibration factor with zero point
3 Nominal diameter/nominal pressure
4 Fluid temperature range
5 Materials: lining/measuring electrode
6 Reserved for additional information on special products
7 Permitted ambient temperature range
8 Observe device documentation
9 Reserved for additional information on device version (approvals, certificates)
10 Calibration tolerance
11 Additional information
– EPD: with empty pipe detection electrode
– R/B: with reference electrode
12 Degree of protection
13 Flow direction
–20°C (–4°F)<Tamb<+50°C (+122°F) NEMA/Type4X
55S1H-XXXXXXXXXXXX
1.0000/0000
–20 ...+150°C/–4 ...+300°F°C °F
PFA
12345678901
ABCDEFGHJKLMNPQRST
DN100 DIN EN PN40/
EPD/MSÜ, R/B
TM:
Order Code:
K-factor:
Ser.No.:
TAG No.:
PROMAG S
1
2
3
712
1.4435/316L
0.2% CAL
4
5
6
10
11
8
9
i
13
N12895
Materials:
Electrodes:

Proline Promag 55 PROFIBUS DP/PA Identification
Endress+Hauser 9
2.1.3 Nameplate for connections
A0006112
Fig. 3: Nameplate specifications for Proline transmitter connections (example)
1 Serial number
2 Possible configuration of current output
3 Possible configuration of relay contacts
4 Terminal assignment, cable for power supply
- Terminal No. 1: L1 for AC, L+ for DC
- Terminal No. 2: N for AC, L- for DC
5 Signals present at inputs and outputs, possible configurations and terminal assignment
6 Version of device software currently installed (incl. language group)
7 Type of communication installed
8 PROFIBUS ID No.
9 Date of installation
10 Current updates to data specified in points 6 to 9
26(+) / 27(–)
NC:
Versorgung /
Tension d'alimentation
Observer manuel d'instruction
See operating manual
Betriebsanleitung beachten
Communication:
Drivers:
Device SW:
ID XXXX (HEX)
XX.XX.XX
PROFIBUS DP
26= B (RxD/TxD-P)
27= A (RxD/TxD-N)
PROFIBUS DP Profile 3.0
()
12345678912Ser.No.:
Supply /
24(+) / 25(–)
22(+) / 23(–)
20(+) / 21(–)
N/L–
PE
A:
NO:
P:
L1/L+
12
319475-00XX
X
active
passive
normally open contact
normally closed contact
Date: DD MMM YYYY
Update 1
Ex-works / ab-Werk / réglages usine Update 2
(WEA)
1
4
5
2
3
10
6
7
8
9

Identification Proline Promag 55 PROFIBUS DP/PA
10 Endress+Hauser
2.2 Certificates and approvals
The devices are designed and tested to meet state-of-the-art safety requirements in accordance with
sound engineering practice. They have left the factory in a condition in which they are safe to
operate. The devices comply with the standards EN 61010 -1 "Protection Measures for Electrical
Equipment for Measurement, Control, Regulation and Laboratory Procedures" and with the
EMC requirements of IEC/EN 61326.
The measuring system described in these Operating Instructions therefore complies with the legal
requirements of the EU Directives. Endress+Hauser confirms this by affixing the CE mark to it and
by issuing the CE declaration of conformity.
The measuring system is in conformity with the EMC requirements of the "Australian
Communications and Media Authority (ACMA)".
The flowmeter has successfully passed all the test procedures carried out and is certified and
registered by the PNO (PROFIBUS User Organization).
The device thus meets all the requirements of the following specifications:
• Certified to PROFIBUS Specification Profile 3.0 version
(Device certification number: provided upon request)
• The measuring device can also be operated with certified devices of other manufacturers
(interoperability).
2.3 Registered trademarks
KALREZ®and VITON®
Registered trademarks of E.I. Du Pont de Nemours & Co., Wilmington, USA
TRI-CLAMP®
Registered trademark of Ladish & Co., Inc., Kenosha, USA
PROFIBUS®
Registered trademark of the PROFIBUS User Organization, Karlsruhe, D
HistoROM™, S-DAT®, T-DAT™, F-CHIP®, FieldCare®, Fieldcheck®, Applicator®
Registered or registration-pending trademarks of Endress+Hauser Flowtec AG, Reinach, CH

Proline Promag 55 PROFIBUS DP/PA Installation
Endress+Hauser 11
3 Installation
3.1 Incoming acceptance, transport and storage
3.1.1 Incoming acceptance
On receipt of the goods, check the following points:
• Check the packaging and the contents for damage.
• Check the shipment, make sure nothing is missing and that the scope of supply matches your
order.
3.1.2 Transport
The following instructions apply to unpacking and to transporting the device to its final location:
• Transport the devices in the containers in which they are delivered.
• Do not remove the protective plates or caps on the process connections until the device is ready
to install. This is particularly important in the case of sensors with PTFE linings.
Special notes on flanged devices
"Caution!
• The wooden covers mounted on the flanges before the device leaves the factory protect the linings
on the flanges during storage and transportation. Do not remove these protection plates until
immediately before the device is installed in the pipe.
• Do not lift flanged devices by the transmitter housing, or the connection housing in the case of
the remote version.
Transporting flanged devices DN 300 (12")
Use webbing slings slung around the two process connections. Do not use chains, as they could
damage the housing.
#Warning!
Risk of injury if the measuring device slips. The center of gravity of the assembled measuring device
might be higher than the points around which the slings are slung.
At all times, therefore, make sure that the device does not unexpectedly turn around its axis or slip.
A0004294
Fig. 4: Transporting sensors with DN 300 (12")

Installation Proline Promag 55 PROFIBUS DP/PA
12 Endress+Hauser
Transporting flanged devices DN > 300 (12")
Use only the metal eyes on the flanges for transporting the device, lifting it and positioning the
sensor in the piping.
"Caution!
Do not attempt to lift the sensor with the tines of a fork-lift truck beneath the metal casing. This
would buckle the casing and damage the internal magnetic coils.
A0004295
Fig. 5: Transporting sensors with DN > 300 (12")
3.1.3 Storage
Note the following points:
• Pack the measuring device in such a way as to protect it reliably against impact for storage (and
transportation). The original packaging provides optimum protection.
• The storage temperature corresponds to the operating temperature range of the measuring
transmitter and the appropriate measuring sensors ä145.
• The measuring device must be protected against direct sunlight during storage in order to avoid
unacceptably high surface temperatures.
• Choose a storage location where moisture does not collect in the measuring device. This will help
prevent fungus and bacteria infestation which can damage the liner.
• Do not remove the protective plates or caps on the process connections until the device is ready
to install. This is particularly important in the case of sensors with PTFE linings.

Proline Promag 55 PROFIBUS DP/PA Installation
Endress+Hauser 13
3.2 Installation conditions
3.2.1 Dimensions
All the dimensions and lengths of the sensor and transmitter are provided in the separate
documentation "Technical Information".
3.2.2 Mounting location
The accumulation of air or gas bubbles in the measuring tube could result in an increase in
measuring errors.
Avoid the following locations:
• At the highest point of a pipeline. Risk of air accumulating.
• Directly upstream from a free pipe outlet in a vertical pipeline.
A0003202
Fig. 6: Mounting location
Installing pumps
Do not install the sensor on the intake side of a pump. This precaution is to avoid low pressure and
the consequent risk of damage to the lining of the measuring tube. Information on the lining's
pressure tightness ä148.
It might be necessary to install pulse dampers in systems incorporating reciprocating, diaphragm or
peristaltic pumps. Information on the measuring system's resistance to vibration and shock
ä145.
A0003203
Fig. 7: Installing pumps
h 2xDN

Installation Proline Promag 55 PROFIBUS DP/PA
14 Endress+Hauser
Partially filled pipes
Partially filled pipes with gradients necessitate a drain-type configuration. The Empty Pipe Detection
function offers additional protection by detecting empty or partially filled pipes ä117.
"Caution!
Risk of solids accumulating. Do not install the sensor at the lowest point in the drain. It is advisable
to install a cleaning valve.
A0003204
Fig. 8: Installation in partially filled pipe
Down pipes
Install a siphon or a vent valve downstream of the sensor in down pipes longer than 5 meters (16 ft).
This precaution is to avoid low pressure and the consequent risk of damage to the lining of the
measuring tube. This measure also prevents the system losing prime, which could cause air
inclusions.
Information on the lining's pressure tightness ä148
A0011902
Fig. 9: Measures for installation in a down pipe (h > 5 m / 16 ft)
1 Vent valve
2Siphon
5xDN
2xDN
h
2
1

Proline Promag 55 PROFIBUS DP/PA Installation
Endress+Hauser 15
3.2.3 Orientation
An optimum orientation position helps avoid gas and air accumulations and deposits in the
measuring tube. Promag, nevertheless, supplies a range of functions and accessories for correct
measuring of problematic fluids:
• Electrode Cleaning Circuit (ECC) for applications with fluids producing buildup, e.g. electrically
conductive deposits ("Description of Device Functions" manual, BA00125D)
• Empty Pipe Detection (EPD) ensures the detection of partially filled measuring tubes, e.g. in the
case of degassing fluids or varying process pressures ä117.
Vertical orientation
A vertical orientation is ideal in the following cases:
• For self-emptying piping systems and when using empty pipe detection.
• For sludge containing sand or stones and where the solids cause sedimentation.
A0011903
Fig. 10: Vertical orientation
Horizontal orientation
The measuring electrode plane should be horizontal. This prevents brief insulation of the two
electrodes by entrained air bubbles.
"Caution!
Empty Pipe Detection functions correctly with the measuring device installed horizontally only
when the transmitter housing is facing upward (see diagram). Otherwise there is no guarantee that
Empty Pipe Detection will respond if the measuring tube is only partially filled or empty.
A0003207
Fig. 11: Horizontal orientation
1 EPD electrode for empty pipe detection
(not available for "measuring electrode only" option, not in Promag H, DN 2 to 15 (1/12 to ½"))
2 Measuring electrodes for signal detection
3 Reference electrode for potential equalization
(not available for "measuring electrode only" option, not in Promag H)
A1
22
A
3

Installation Proline Promag 55 PROFIBUS DP/PA
16 Endress+Hauser
3.2.4 Inlet and outlet runs
If possible, install the sensor well clear of fittings such as valves, T-pieces, elbows, etc.
Compliance with the following requirements for the inlet and outlet runs is necessary in order to
ensure measuring accuracy.
• Inlet run 5 × DN
•Outletrun2 × DN
A0003210
Fig. 12: Inlet and outlet runs
3.2.5 Vibrations
Secure the piping and the sensor if vibration is severe.
"Caution!
It is advisable to install the sensor and transmitter separately if vibration is excessively severe.
Information on the permitted resistance to vibration and shock ä145.
A0003208
Fig. 13: Measures to prevent vibration of the measuring device (L > 10 m / 33 ft)
5xDN2xDN
L

Proline Promag 55 PROFIBUS DP/PA Installation
Endress+Hauser 17
3.2.6 Foundations, supports
If the nominal diameter is DN 350 (14"), mount the sensor on a foundation of adequate load-
bearing strength.
"Caution!
Risk of damage.
Do not support the weight of the sensor on the metal casing: the casing would buckle and damage
the internal magnetic coils.
A0003209
Fig. 14: Correct support for large nominal diameters (DN 350 / 14")
3.2.7 Adapters
Suitable adapters to DIN EN 545 (double-flange reducers) can be used to install the sensor in larger-
diameter pipes. The resultant increase in the rate of flow improves measuring accuracy with very
slow-moving fluids.
The nomogram shown here can be used to calculate the pressure loss caused by cross-section
reduction.
!Note!
The nomogram only applies to liquids of viscosity similar to water.
1. Calculate the ratio of the diameters d/D.
2. From the nomogram, read off the pressure loss as a function of fluid velocity (downstream from
the reduction) and the d/D ratio.
A0003213
Fig. 15: Pressure loss due to adapters
100
10
0.5
d/D
[mbar]
0.6 0.7 0.8 0.9
1 m/s
2 m/s
3 m/s
4 m/s
5 m/s
6 m/s
7 m/s
8 m/s
1
D
d
max. 8°

Installation Proline Promag 55 PROFIBUS DP/PA
18 Endress+Hauser
3.2.8 Nominal diameter and flow rate Promag S and Promag H
The diameter of the pipe and the flow rate determine the nominal diameter of the sensor. The
optimum flow velocity is between 2 and 3 m/s (6 to 10 ft/s). The flow velocity (v), moreover, has
to be matched to the physical properties of the fluid:
• v < 2 m/s (< 6 ft/s): for abrasive fluids where solids do not cause sedimentation (e.g. lime milk)
• v > 2 m/s (> 6 ft/s): for fluids producing buildup (e.g. wastewater sludge)
• v > 2 m/s (> 6 ft/s): for abrasive sludge with a high sand or stone content and where the solids
easily cause sedimentation (e.g. ore slurry)
!Note!
Flow velocity can be increased, if necessary, by reducing the nominal diameter of the sensor through
the use of adapters ä17.
Flow rate characteristic values - Promag S (SI units)
Nominal
diameter
Recommended flow rate Factory settings
[mm]
min./max. full scale value
(v 0.3 or 10 m/s)
Low flow cut off
(v 0.04 m/s)
15 4…100 dm3/min 0.5 dm3/min
25 9…300 dm3/min 1 dm3/min
32 15…500 dm3/min 2 dm3/min
40 25…700 dm3/min 3 dm3/min
50 35…1100 dm3/min 5 dm3/min
65 60…2000 dm3/min 8 dm3/min
80 90…3000 dm3/min 12 dm3/min
100 145…4700 dm3/min 20 dm3/min
125 220…7500 dm3/min 30 dm3/min
150 20…600 m3/h 2.5 m3/h
200 35…1100 m3/h 5.0 m3/h
250 55…1700 m3/h 7.5 m3/h
300 80…2400 m3/h 10 m3/h
350 110…3300 m3/h 15 m3/h
400 140…4200 m3/h 20 m3/h
450 180…5400 m3/h 25 m3/h
500 220…6600 m3/h 30 m3/h
600 310…9600 m3/h 40 m3/h

Proline Promag 55 PROFIBUS DP/PA Installation
Endress+Hauser 19
Flow rate characteristic values - Promag S (US units)
Nominal
diameter
Recommended flow rate Factory settings
[inch]
min./max. full scale value
(v 1.0 or 33 ft/s)
Low flow cut off
(v 0.1 ft/s)
½" 1.0…27 gal/min 0.10 gal/min
1" 2.5…80 gal/min 0.25 gal/min
1 ¼" 4…130 gal/min 0.50 gal/min
1 ½" 7…190 gal/min 0.75 gal/min
2" 10…300 gal/min 1.25 gal/min
2 ½" 16…500 gal/min 2.0 gal/min
3" 24…800 gal/min 2.5 gal/min
4" 40…1250 gal/min 4.0 gal/min
5" 60…1950 gal/min 7.0 gal/min
6" 90…2650 gal/min 12 gal/min
8" 155…4850 gal/min 15 gal/min
10" 250…7500 gal/min 30 gal/min
12" 350…10600 gal/min 45 gal/min
14" 500…15000 gal/min 60 gal/min
16" 600…19000 gal/min 60 gal/min
18" 800…24000 gal/min 90 gal/min
20" 1000…30000 gal/min 120 gal/min
24" 1400…44000 gal/min 180 gal/min

Installation Proline Promag 55 PROFIBUS DP/PA
20 Endress+Hauser
Flow rate characteristic values - Promag H (SI units)
Flow rate characteristic values - Promag H (US units)
Nominal
diameter
Recommended flow rate Factory settings
[mm] [inch]
min./max. full scale value
(v 0.3 or 10 m/s)
Full scale value (v 
2.5 m/s)
Pulse value (2
pulse/s)
Low flow cut off
(v 0.04 m/s)
2 1/12" 0.06…1.8 dm3/min 0.5 dm3/min 0.005 dm30.01 dm3/min
4 5/32" 0.25…7 dm3/min 2 dm3/min 0.025 dm30.05 dm3/min
8 5/16" 1…30 dm3/min 8 dm3/min 0.10 dm30.1 dm3/min
15 1/2" 4…100 dm3/min 25 dm3/min 0.20 dm30.5 dm3/min
25 1" 9…300 dm3/min 75 dm3/min 0.50 dm31dm
3/min
32 1 1/4" 15…500 dm3/min 125 dm3/min 1.00 dm32dm
3/min
40 1 1/2" 25…700 dm3/min 200 dm3/min 1.50 dm33dm
3/min
50 2" 35…1100 dm3/min 300 dm3/min 2.50 dm35dm
3/min
65 2 1/2" 60…2000 dm3/min 500 dm3/min 5.00 dm38dm
3/min
80 3" 90…3000 dm3/min 750 dm3/min 5.00 dm312 dm3/min
100 4" 145…4700 dm3/min 1200 dm3/min 10.00 dm320 dm3/min
Nominal
diameter
Recommended flow rate Factory settings
[inch] [mm]
min./max. full scale value
(v 0.3 or 10 m/s)
Full scale value (v 
2.5 m/s)
Pulse value (2
pulse/s)
Low flow cut off
(v 0.04 m/s)
1/12" 2 0.015…0.5 gal/min 0.1 gal/min 0.001 gal 0.002 gal/min
5/32" 4 0.07…2 gal/min 0.5 gal/min 0.005 gal 0.008 gal/min
5/16" 8 0.25…8 gal/min 2 gal/min 0.02 gal 0.025 gal/min
1/2" 15 1.0…27 gal/min 6 gal/min 0.05 gal 0.10 gal/min
1" 25 2.5…80 gal/min 18 gal/min 0.20 gal 0.25 gal/min
1 1/4" 32 4…130 gal/min 30 gal/min 0.20 gal 0.5 gal/min
1 1/2" 40 7…190 gal/min 50 gal/min 0.50 gal 0.75 gal/min
2" 50 10…300 gal/min 75 gal/min 0.50 gal 1.25 gal/min
2 1/2" 65 16…500 gal/min 130 gal/min 1 gal 2.0 gal/min
3" 80 24…800 gal/min 200 gal/min 2 gal 2.5 gal/min
4" 100 40…1250 gal/min 300 gal/min 2 gal 4.0 gal/min