Eneo IAR-7SE2024MMA User manual

Quick Installation Guide
Gigabit Switch, Managed, 250W,
24x PoE, 4x SFP, 1000Mbps,
Wall-/Rack Mounting, Desktop
IAR-7SE2024MMA
EN

About Documents
This document is Quick Installation Guide. It is intended for engineers or anyone who
needs to install the product.
Announcement
The information in this document is subject to change without notice.
The document is only used as operation guide, except for other promises. No
warranties of any kind, either express or implied are made in relation to the description,
information or suggestion or any other contents of the manual.
The images shown here are indicative only. If there is inconsistency between the image
and the actual product, the actual product shall govern.
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol Description
DANGER Indicates a hazard with a high level of risk, which if not
avoided, will result in death or serious injury.
WARNING Indicates a hazard with a medium or low level of risk,
which if not avoided, could result in minor or moderate
injury.
CAUTION Indicates a potentially hazardous situation, which if not
avoided, could result in equipment damage, data loss,
performance degradation, or unexpected results.

Content
Packing List............................................................................................1
Product Introduction..............................................................................2
2.1 Overview ......................................................................................2
2.2 Hardware Introduction..................................................................2
3.1 Safety Precaution.........................................................................4
3.2 Insatallation Steps........................................................................6
3.2.1 Rack Mount ..................................................................................7
3.2.2 Desktop Installation......................................................................8
3.2.3 Wall Mount....................................................................................8
3.2.4 AC Power Cable Connection........................................................9

1
Packing List
Open the box of the product and carefully unpack it. The box should contain the
following items. Please check before installation, if any missing, please contact your
dealer immediately.
No.
Items
Quantity
1
Switch
1 pc
2
AC Power Cable
1 pc
3
Mounting Accessory
1 set
4
Quick Installation Guide
1 pc

2
Product Introduction
2.1 Overview
This series product is 16-Port/24-Port Gigabit PoE + 4-Port Gigabit SFP L2 Managed
Ethernet Switch (250W).
This series switch provides 16/24 Gigabit Ethernet RJ-45 ports and 4 Gigabit SFP
uplink ports. The switch meets IEEE 802.3af/at standard. All RJ-45 ports support
Power-over-Ethernet (PoE+) and deliver up to 30W power per port.
The switch has extensive L2 management functions, such as 802.1Q VLAN, 802.1P
QoS, STP/RSTP, Link aggregation, DHCP and PoE control. It can be easily managed
via a WEB GUI (http/https), CLI (telnet/ssh/console) or SNMP.
This series contains two types:
16-Port Gigabit PoE + 4-Port Gigabit SFP L2 Managed Ethernet Switch (250W)
(short for 16-Port PoE Switch)
24-Port Gigabit PoE + 4-Port Gigabit SFP L2 Managed Ethernet Switch (250W)
(short for 16-Port PoE Switch)
2.2 Hardware Introduction
Front Panel (16-Port PoE Switch)
Front Panel (24-Port PoE Switch)

3
Rear Panel (16-Port/24-Port PoE Switch)
Led Indicators Instructions
Indicators
Status
Descriptions
PWR
Power Supply Indicator
On
The Main Power Supply is working.
Off
The Main Power Supply is off.
Link
Port Link Indicators
On
The port is linking normally.
Blink
The port is transmitting or receiving
data.
Off
The port links down.
PoE
Port PoE Indicators
On
The port is supplying PoE power
normally.
Off
The port stops supplying PoE power.
Console Port
The device contains aserial RS-232 interface as the console port for local management
interface. For the console port, a standard RJ-45 connector is used. Use a RS-232
calbe (Sub-D9 to RJ-45) to connect the console port with the COM port of a PC.
Default configuration:
Data
Default value
Transfer rate
115200 bit/s
Flow control mode
Not support
Test mode
Not support
Stop bits
1
Data bits
8

4
Installations
3.1 Safety Precaution
To minimize the technically residual risk, it is imperative to obey the following rules.
Read all the instructions before operation.
The Caution, Warning and Danger items in the document does not cover all the safety
precautions that must be followed. They are only supplementary information.
When operating the device, obey the local safety regulations. The safety precautions
provided in the documents are supplementary and shall be in compliance with the local
safety regulations.
Operator
Only qualified and skilled personnel can install, configure, and disassemble the
device.
Only the personnel authorized can operate the device.
Any replacement or change to the device or parts of the device (including the
software) must be done by qualified or authorized personnel.
Any fault or error that might cause safety problems must be reported immediately
to the person in charge.
Ground
For better protection performance, it is recommended as follows.
Do not damage the ground conductor or operate the device in the absence of well
installed ground conductor. Conduct the appropriate electrical inspection.
When operating the unit, always make the ground connection first and disconnect
it at the end.
Human Safety
Do not operate the device or cables at lightning strikes.
If the device is designed with optical port, do not look directly into the optical port to
prevent the laser radiation from injuring your eyes.
Do not wear jewelry or watches when you operate the device.
Equipment Safety
Before operation, the device must be fixed securely on the floor or to other reliable
objects, such as the desktop, the walls or the mounting racks.
Do not block the ventilation while the device is running. Keep a minimum distance
of 5 cm from the ventilation to the walls or the other objects that block the ventilation.
Tighten the thumbscrews by using a tool after both initial installation and
subsequent access to the panel.

5
Inflammable Environment
DANGER
Do not place the device in the environment that has inflammable and explosive air
or fog. Do not perform any operation in this environment.
Operating the electrical device in inflammable environment can be fatal.
Moisture Proof
WARNING
Water or moisture in the equipment will damage the circuit of the equipment.
The installation environment of the equipment must be strictly prohibited from water
seepage, dripping, and condensation, otherwise it is necessary to install
dehumidification equipment (such as air conditioners with dehumidification function,
special dehumidifiers), etc.
It is forbidden to operate the equipment under or near the water source, such as
the sink, laundry room or other high humidity areas.
It is forbidden to touch the device with wet hands.
Dust Proof
Install the equipment far away from sand and dust sources, such as coal mines,
rural roads, and farmland, etc.
It is forbidden to operate the device in a dense dust environment.
Ventilation
WARNING
Operating equipment will release heat. Please ensure that the environment where
the equipment is installed is well ventilated to ensure the equipment operating
normally.
It is strictly forbidden to install the equipment near heat sources, such as stoves,
heaters, etc.
Ensure that the equipment installation environment has good air flow.
If the equipment is designed with heat dissipation holes, it is strictly prohibited to
block the heat dissipation hole of the device.

6
3.2 Installation Steps
This series switch supports 3 installation methods:
Rack mount
Desktop installation
Wall mount
Following with the dimensions of the switch and its insatallation accessories. The two
types are of the same dimensions. Here take 24-Port PoE Switch as example.
Dimensions (mm)

7
3.2.1 Rack Mount
This series switch supports 19” rack-mounted installtaion. Following with the installation
steps.
Step 1: Fix the hangers on the side of the switch.
Accessories
Step 2: Install the switch on the rack with screws in the
package.
Accessories
Step 3: Continue to install other devices in the rack. The
distance between the devices should be more than 5cm.
Accessories

8
3.2.2 Desktop Installation
This series switch supports desktop installation. Users can put this product on clean,
stable, grounded workbench. The installation steps are as below:
Carefully put the device upside down, clean the grooves on the chassis backplane
with soft cloth to make sure there is no oil or dust in it.
Remove the stickers on the foot pad, paste the foot pad in backplane groove.
Carefully put the device upright on the workbench.
3.2.3 Wall Mount
This series switch supports wall-mounted installation. Users can put the switch on clean,
steady vertical wall. Installation steps are as below:
Step 1 Fix the hangers to the switch.
Accessories
Step 2 Drill 4 holes on the wall where device is installed,
then drive the rubber plug into the hole. Drive these
screws into the hole for the rack and fix the product by
aiming at the rubber plug.
Accessories
4*

9
3.2.4 AC Power Cable Connection
This series switch is equipped with one built-in power supply module.
Power supply module specifications:
Items
Specifications
Power Input
Input Voltage
AC 100~240V 50/60Hz
Input Current
4A max
Power Output
Output Voltage
54V DC
Output Current
5.2A max
Power Consumption
280.8W (Full load)
Connect the AC power cable to the switch through the power input interface. It is
recommended to use the AC power cable provided in the package.
Connect the switch to AC power. Check if the power indicator turns on, which means
the power is connected correctly.
CAUTION
For better transmission performance, it is recommended to use Cat5 or better
cables to connect the switch and powered devices.
For better protection performance, it is recommended always to make the ground
connection first and disconnect it at the end when operating the unit.
Power on the system only after confirming that the wiring is correct, to avoid
damage to the equipment.
Read the user manual carefully before operating or maintaining the repeater to
avoid misoperation.
The installation steps are finished.

10
Specifications
Items
16-Port PoE Switch
24-Port PoE Switch
Ethernet Ports
Downlink Ports
16* 10/100/1000Base-T PoE
RJ-45(Auto-MDI/MDI-X)
24*10/100/1000Base-T PoE
RJ45 (Auto-MDI/MDI-X)
Uplink Ports
4*1000 Base-X SFP
Console Port
1*RJ-45 to RS-232 console port(115200, 8, N, 1)
PoE
PoE Standard
IEEE 802.3af/at (PSE)
PoE Power Supply
Type
End-span
PoE Pin Assignment
1/2(+), 3/6(-)
PoE Power Output
54V DC
PoE Power
30W for each port
230W max
30W for each port
230W max
Switch Property
Standards
IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z,
IEEE 802.3x, IEEE 802.1Q, IEEE 802.1p,IEEE 802.3ad,
IEEE 802.1D, IEEE 802.1x
Forwarding Modes
Store and Forward
Packet Buffer
12MB
MAC Table
16k, supported auto learning
Switching Capacity
40Gbps / non-blocking
56Gbps / non-blocking
Packet Forwarding
Rate
29.8Mpps
41.7Mpps
Jumbo Frame
10kB
Power Supply
Input Voltage
100~240VAC 50/60Hz
Power Consumption
250W
(Full load including PoE)
250W
(Full load including PoE)
Reliability
Surge Immunity
6kV, Standard: IEC61000-4-5
ESD
6kV Contact discharge, 8kV Air discharge
Standard: IEC61000-4-2
MTBF
334959h 322194h
MTBF Standards
Telcordia SR-332, 25

11
Operating
Temperature
-10~50
Storage
Temperature
-40~85
Operating Humidity
5%~95% (Non-condensation)
Physical Parameters
Led Indicators
1*PWR Indicator
16*Downlink Port Link
Indicator
16*Downlink Port PoE
Indicator
4*Uplink Port Link Indicator
1*PWR Indicator
24*Downlink Port Link
Indicator
24*Downlink Port PoE
Indicator
4*Uplink Port Link Indicator
Init Button
Short press to restart
Long press 5s to initialize the system
Dimension(W*D*H)
442mm*286mm*44mm
Gross Weight
1900g±20g 2010g±20g
Net Weight
1620g±20g 1730g±20g
Material
Metal shell
Installation
Rack mounted/desktop/wall mounted
Certifications
Certifications
CE, FCC

eneo® is a registered trademark of
VIDEOR E. Hartig GmbH
Exclusive distribution through specialised
trade channels only.
VIDEOR E. Hartig GmbH
Carl-Zeiss-Straße 8
63322 Rödermark/Germany
Tel. [phone] / 888-0
Fax [phone] / 888-100
www.videor.com
www.eneo-security.com
Technical changes reserved
© Copyright by VIDEOR E. Hartig
GmbH Version 03/2021