Enerpac ETW Series User manual

Instruction Sheet
Electric
Torque
Wrench
ETW Series
ETW1000
ETW2000
ETW3000
ETW6000
L4085
Rev. D 6/16
English (EN)

The following languages
are included:
Note: Download the latest version of Adobe Reader at:
http://get.adobe.com/reader
English (EN)
Français (FR)
Deutsch (DE)
Italiano (IT)
Español (ES)
Nederlands (NL)
Português Brasileiro (PT)
Pyccкий (RU)
简体中文 (ZH)
日本語 (JA)
한국어 (KO)
Instruction Sheets in Adobe®PDF format
Please find the CD or DVD enclosed in the back of this manual

Instruction Sheet
ETW Series
Electric Torque Wrench
ETW1000
ETW2000
ETW3000
ETW6000
© 2016 Enerpac, All Rights Reserved
1.0 Introduction ....................................................4
1.1 Overview ................................................4
1.2 Delivery Instructions.............................4
1.3 CE Declaration of Conformity..............4
2.0 Safety ..............................................................5
2.1 Safety Definitions..................................5
2.2 General Safety .......................................5
2.3 ETW Series Safety.................................6
2.4 Electrical Safety ....................................7
2.4.1 Use and Care.............................7
2.4.2 Disconnecting the
Control Box................................7
2.4.3 Grounding Instructions ............8
3.0 Assembly ........................................................8
3.1 Serial Number Matching.......................8
3.2 Electrical Power Requirements .........10
3.3 Install Reaction Arm ...........................10
3.4 Shoulder Strap.....................................11
3.4.1 Shoulder Strap Safety
Precautions..............................11
3.4.2 Shoulder Strap Installation ....12
3.5 Control Box Touchscreen Use ...........13
3.5.1 Home Screen ..........................14
3.5.2 Manual Mode Screen .............15
3.5.3 Automatic Mode Screen ........16
3.5.4 Automatic Preset
Mode Screen ...........................17
Table of Contents
3.5.5 Edit Automatic
Preset Screen ..........................18
3.5.6 Edit Preset
Description Screen .................19
3.5.7 Edit Preset Number Screen ...20
3.5.8 Edit Torque Value Screen.......21
3.5.9 Edit Torque Angle Screen ......22
3.5.10 Tool Setup Screen.................23
3.5.11 Data Setup Screen................24
3.5.12 Data View Screen .................25
3.5.13 Export Data Screen ..............26
3.5.14 Viewing the Exported
Data on a Computer .............28
3.5.15 Torque Wrench
Display Functions..................29
4.0 Operation......................................................30
4.1 To Tighten a Fastener .........................31
4.2 To Loosen a Fastener..........................34
4.3 Shutdown and Storage .......................35
5.0 Maintenance.................................................36
6.0 Troubleshooting ..........................................36
7.0 Technical Specifications .............................37
7.1 Imperial System...................................37
7.2 Metric System .....................................38

4 © 2016 Enerpac, All Rights Reserved
ETW Series Electric Torque Wrench
1.0 INTRODUCTION
1.1 Overview
The Enerpac ETW Series torque wrench is designed for controlled tightening and loosening of fasteners in
industrial bolting applications.
The ETW Series is available as a package with the following items:
• 1 Touchscreen Control Box (1)
• 1 Storage Case (2)
• 1 ETW Series Electric Torque Wrench (3)
• 1 Standard Reaction Arm (4)
Optional reaction arms are available for dierent
applications.
1.2 Delivery Instructions
Upon delivery, all components must be inspected
for damage incurred during shipping. If damage
is found, the carrier should be notified at once.
Shipping damage is not covered by the Enerpac
warranty.
1.3 CE Declaration of Conformity
ETW1000 • ETW2000 • ETW3000 • ETW6000
Enerpac declares that the ETW Series electric torque wrenches meet the applicable standards and directives
issued by the European Union.
1
2
4
3

© 2016 Enerpac, All Rights Reserved 5
ETW Series Electric Torque Wrench
2.0 SAFETY
Read all instructions carefully. Follow all recommended safety precautions to avoid personal injury as well
as damage to the wrench and/or damage to other property. Enerpac cannot be responsible for any damage
or injury from unsafe use, lack of maintenance or incorrect operation. Do not remove warning labels, tags
or decals. In the event any questions or concerns arise, contact Enerpac or a local Enerpac distributor for
clarification.
This manual follows a system of safety alert symbols, signal words and safety messages to warn the user of
specific hazards. Failure to comply with these warnings could result in death or serious personal injury, as well
as damage to the equipment or other property.
2.1 Safety Definitions
!
The Safety Alert Symbol appears throughout this manual. It is used to alert you to potential
physical injury hazards. Pay close attention to Safety Alert Symbols and obey all safety messages
that follow this symbol to avoid the possibility of death or serious personal injury.
Safety Alert Symbols are used in conjunction with certain Signal Words that call attention to safety messages
or property damage messages and designate a degree or level of hazard seriousness. The Signal Words used
in this manual are DANGER, WARNING, CAUTION and NOTICE.
DANGER
!Indicates a hazardous situation, if not avoided, will result in death or serious personal
injury.
WARNING
!Indicates a hazardous situation, if not avoided, could result in death or serious personal
injury.
CAUTION
!Indicates a hazardous situation, if not avoided, could result in minor or moderate personal
injury.
Indicates information considered important but not hazard-related (e.g., messages relating to
property damage). Please note that the Safety Alert Symbol will not be used with this signal word.
2.2 General Safety
Be aware that the operator is fully responsible for the correct operation of this tool. Enerpac is not responsible
for damage or injury caused by misuse of this tool. Under some circumstances, additional safety precautions
beyond those described in this manual may be required. Read this manual carefully and observe all safety
precautions.
• Be sure you have read and understood the instruction manual prior to using the tool. Contact Enerpac
if you have questions.
• Make sure you have completed safety training, specific to the work surroundings. The operator should
be thoroughly familiar with the controls and the proper use of the tool.
• The operator must be of at least the minimum age required by applicable local regulations, laws and
the facility’s standard operating procedures.
• Make sure your workplace is safe.

6 © 2016 Enerpac, All Rights Reserved
ETW Series Electric Torque Wrench
Follow instructions in your workplace’s standard operating procedures and be sure to observe all
communicated safety precautions.
2.3 ETW Series Safety
The following warnings are specific to the ETW Series Electric Torque Wrench.
DANGER
!Do not place any part of the body between the reaction arm and the reaction point.
WARNING
!Failure to observe and comply with the following precautions could result in death or
serious personal injury. Property damage could also occur.
• Be aware that a nut or bolt that breaks o during operation of the tool may become a high-velocity
projectile.
• Always wear protective headwear, eye protection, ear protectors, footwear and gloves (at a minimum,
rigger-type gloves) suitable for safe operation of the tool. The protective clothing must not interfere
with safe operation of the tool or restrict the ability to communicate with coworkers.
• Do not place any objects between the reaction arm and the reaction point. Keep the cords away from
the reaction points.
• Tightening and loosening nuts and bolts involves little visible movement. The pressure and loads,
however, are extreme. Keep your hands away from the fastener being loosened or tightened.
• Keep loose clothing, hair and other items from being caught in any rotating part of the tool.
CAUTION
!Failure to observe and comply with the following precautions could result in minor or
moderate personal injury. Property damage could also occur.
• Make sure the control box power switch is o before connecting tool to the control box.
• Always use sockets which are designed for use with powered wrenches.
• Always position the tool for maximum stability. Make sure reaction points are adequate for the forces
at work during operation of the tool.
• Make sure the reaction point is of a suitable shape. For example, use an adjacent nut or bolt as a
reaction point.
• The maximum torque output rating of the tool must always exceed the torque required to loosen or
tighten the nut or bolt.
• Bolt lubricants and anti-seize compounds will have a rated coecient of friction. Be sure to know the
coecient of friction for the lubricant or anti-seize compound that is being used. To ensure proper
tightening of nuts and bolts, always use this coecient of friction when calculating required torque
values.
• Do not drop heavy objects on the cords. A sharp impact may cause internal damage to the cord.
• Always carry the wrench by its housing or with an Enerpac-approved eyebolt and carrying strap. Never
use the electrical cords to carry or move the tool or the touchscreen control box.

© 2016 Enerpac, All Rights Reserved 7
ETW Series Electric Torque Wrench
ELECTROSTATIC DISCHARGE SAFETY PRECAUTIONS
• In case of any heavy static build-up, the tool will stop running. The microprocessor inside the tool will
revert to a safe mode and the LED on the tool will display 200 Ft.Lbs. Such a heavy build-up of static
will have no impact on the control box.
• Prior to re-using the tool, please ensure that measures are taken to prevent any accumulation of such
static electricity. Before operating the tool, the operator can discharge any static by touching any
metallic body, other than the tool. Or, in extreme cases of frequent occurrence of such disturbances,
the operator can wear an ESD strap.
• To re-start the operation, the operator can either:
a. adjust the torque value on the control box screen, which will re-establish the communication
between the tool and the control box, or,
b. turn the control box o and turn it on again.
Failure to observe and comply with the following precautions could result in property damage
and/or void the product warranty.
• If the tool is dropped from a significant height, have the tool inspected before you operate it again.
• In severe conditions, the tool must be cleaned and inspected more frequently.
• Be sure to minimize torsional and bending stresses in the tool and any accessories.
• Avoid striking the tool at any time, even when it is not under load. Striking the tool could cause
permanent damage to wrench components and may aect the wrench calibration.
• Always use Enerpac spare parts.
• Ensure that the tool and related equipment are in good working condition prior to use.
2.4 Electrical Safety
DANGER
!RISK OF ELECTRIC SHOCK! CONNECT THE CONTROL BOX TO A PROPERLY GROUNDED
OUTLET ONLY!
2.4.1 Use and Care
• Store the equipment indoors when not in use. Keep out of reach of children.
• Do not clean the equipment with a water spray or the like.
• Do not operate the equipment with a damaged cord or plug, or after the equipment malfunctions or is
dropped or damaged in any manner. Return the equipment to the nearest authorized service facility for
examination, or electrical or mechanical repair.
2.4.2 Disconnecting the Control Box
To disconnect, turn the On/O switch on the control box to the OFF (“O”) position, then remove plug from
outlet.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Unplug from outlet when not in use and before servicing or cleaning.

8 © 2016 Enerpac, All Rights Reserved
ETW Series Electric Torque Wrench
2.4.3 Grounding Instructions
This appliance must be grounded. In the event of malfunction or breakdown, grounding provides a path
of least resistance for electric current to return to ground, thereby reducing the risk of electrical shock. This
appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug
must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local
codes and ordinances.
The ETW Series electric torque wrench is equipped with a Ground Fault Monitoring System. In case
of an improper grounding, the circuit will deactivate the wrench motor and the ground fault/low voltage light
on the control box panel will shine red. If this occurs, turn o the control box power and check the ground
connections.
DANGER
!Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. The conductor with insulation having an outer surface that is green with or without
yellow stripes is the equipment-grounding conductor. If repair or replacement of the cord or plug
is necessary, do not connect the equipment-grounding conductor to a live terminal. Check with a
qualified electrician or serviceman if the grounding instructions are not completely understood, or if in
doubt as to whether the tool is properly grounded. Do not modify the plug provided with the tool. If it
will not fit the outlet, have a proper outlet installed by a qualified electrician.
A qualified electrician should be consulted if there is any doubt as to whether an outlet box is properly
grounded.
This unit is for use on a circuit having a nominal rating more than 115V (115-volt model) 230V (230-volt model)
and is factory equipped with a specific electric cord and plug. No adapter without a proper ground connection
should be used with this unit. If the unit must be reconnected for use on a dierent type of electric circuit,
the reconnection should be made by qualified service personnel; and after the reconnection, the unit should
comply with all local codes and ordinances.
3.0 ASSEMBLY
3.1 Serial Number Matching
CAUTION
!The torque wrench and the touchscreen control box are a matched set and must be
used together. Using a control box and wrench containing dierent serial numbers may result in
erratic operation with the potential to cause personal injury and tool damage. Loss of calibration and
inaccurate torque settings will also result.
Before connecting the wrench to the touchscreen control box, locate the serial numbers on the touchscreen
control box and the wrench. The serial numbers must match each other. Do not connect the wrench to the
touchscreen control box if the serial numbers do not match.

© 2016 Enerpac, All Rights Reserved 9
ETW Series Electric Torque Wrench
SERIAL NO:
POWER
ON/OFF
VOLTAGE:
2
1
GROUND FAULT
LOW VOLTAGE 1 - Touchscreen Control Box Serial Number
Location
2 - Torque Wrench Serial Number Location
Fig. 1
The servo motor control cord, servo motor power cord and the main power cord must be connected to the
touchscreen control box before using the tool.
1. Connect the servo control cord and the servo motor power cord to the control box by lining up the bosses
on the male wire connectors with the notches in the female connector.
2. Push the male connector into the female connector. With the connector fully inserted, turn the locking ring
a quarter turn to lock the connectors together.
1
35
6
4
2
1 - Female Connector – Servo Motor Control
2 - Male Connector – Servo Motor Control
3 - Female Connector – Servo Motor Power
4 - Male Connector – Servo Motor Power
5 - Female Connector – Main Power
6 - Male Connector – Main Power
Fig. 2
Serial numbers on control box (1)
and wrench (2) must match

10 © 2016 Enerpac, All Rights Reserved
ETW Series Electric Torque Wrench
3. Connect the main power cord by aligning the bosses with the notches and push the male connector into
the female connector. With the connector fully inserted, turn the locking ring to thread it onto the female
connector. Tighten hand tight to lock the connectors together.
3.2 Electrical Power Requirements
The control box voltage is located on the front panel, under the serial number. Two dierent control box
versions are available:
115 Volt Version 115 volts, single-phase, 50 – 60 Hz, minimum circuit rating current 22 amps
208 – 240 Volt Version 208 – 240 volts, single-phase, 50 – 60 Hz, minimum circuit rating current 11 amps
Be certain that the power supply voltage is correct for your control box version. Connecting the
control box to an incorrect voltage will cause damage to the control box and tool.
3.3 Install Reaction Arm
1. Place the reaction arm onto the tool.
2. Using your fingers, thread the setscrew in by hand until it bottoms-out in the groove of the reaction spline.
Do not over-tighten.
Fig. 3
3. Plug the main power cord into a correctly rated outlet.

© 2016 Enerpac, All Rights Reserved 11
ETW Series Electric Torque Wrench
3.4 Shoulder Strap
The ETW tools are equipped to accommodate shoulder straps, which are supplied with select models, or as
an accessory.
The use of shoulder straps is associated with certain risks, which increase when the straps are used with the
larger and heavier ETW models. Section 3.4.1 provides safety instructions pertaining to shoulder strap usage.
3.4.1 Shoulder Strap Safety
WARNING
!Loss of control of the tool while using a shoulder strap could result in death or serious
personal injury. Property damage could also occur.
Loss of control of the tool while it is strapped around the neck and/or shoulder could result in:
• Impact injuries to the back of the neck, shoulders, and/or lower back.
• Loss of balance, resulting in the user’s collision with nearby structures or moving machinery.
• A fall from an elevated position, if the user is working at an elevation.
In addition, strap failure could cause the tool to drop unexpectedly, which could result in:
• Potential personal injury to the operator and/or persons working nearby or below.
• Damage to the tool and/or objects below.
When using a shoulder strap to assist in transporting, supporting, and positioning the tool, always observe the
following instructions and precautions:
• Adjust the shoulder strap to the shortest possible length that will allow sucient range of movement
during use. This will minimize the drop and potential impact in the event of loss of control.
• Be especially aware of footing when carrying the tool while using a shoulder strap. Wear proper safety
shoes to avoid slipping and potential injuries.
• Use appropriate gloves to maximize grip on the tool to avoid loss of control.
• Avoid using the shoulder strap in confined areas or near moving machinery, where the impact caused
by dropping the tool could force the user into an immovable structure or into dangerous moving
machinery.
• When working at an elevation, always wear fall protection devices to help prevent serious falls.
• Consider using a balancer or crane to support the tool, especially when using the larger ETW models.
This will help avoid the inherent dangers of supporting the tool’s weight with a user’s neck and
shoulders. When working at an elevation, these devices can also help prevent the tool from dropping
on persons below.
• Always monitor the condition of shoulder strap and hardware. Replace if any of the following are
found: cuts or abrasions on strapping, loose stitching, cracked or bent hardware, or improperly
operating clasps.

12 © 2016 Enerpac, All Rights Reserved
ETW Series Electric Torque Wrench
3.4.2 Shoulder Strap Installation
Instructions:
1. Fully install the eyebolt into the threaded hole at the top of the housing.
2. Attach one end of the shoulder strap to the eyebolt. Attach the other end of the shoulder strap to the
metal loop at the base of the wrench grip. Be sure that both clasps are fully closed.
3. Adjust the shoulder strap to the shortest possible length that will allow sucient range of movement
during use. Remove any excess slack.
1 - Eyebolt
2 - Clasp
3 - Shoulder Strap
4 - Metal Loop
Fig. 4
1
2
3
2
4

© 2016 Enerpac, All Rights Reserved 13
ETW Series Electric Torque Wrench
3.5 Control Box Touchscreen Use
• Press the touchscreen on/o switch (I) to turn on the control box power.
• An indicator light is located on the upper left hand corner of the control box panel. On 230V models, this
light is the “ground fault indicator light”. On 115V models, it is the “ground fault/low voltage indicator light”.
• Observe the indicator light after turning on the control box power:
All models: The indicator light will illuminate RED briefly after power is turned on, and then should
turn o after a few seconds. If the light remains red and does not turn o, it is an indication that the
tool is improperly grounded. Check the condition of the electrical supply. Ensure that proper grounding
is provided.
115V models only: If the indicator light illuminates YELLOW after power is turned on, this indicates
that the line voltage being supplied to the control box is too low. Check the condition of the electrical
supply. Verify that sucient voltage is available before using the tool.
• To clear the faults, turn o the control box power and then turn it on again.
230V models are not equipped with a low voltage indication feature.
1 - Control Box Touchscreen
2 - On/O Switch
3 - Ground Fault / Low Voltage Indicator Light
(115V Models Only)
4 - Ground Fault Indicator Light
(230V Models Only)
Fig. 5
SERIAL NO:
POWER
ON/OFF
VOLTAGE:
1
GROUND FAULT
LOW VOLTAGE
3
4
12

14 © 2016 Enerpac, All Rights Reserved
ETW Series Electric Torque Wrench
3.5.1 Home Screen
• After the initial boot up, the “Home” screen will be displayed.
homeback
DATA SETUP
TOOL SETUP
AUTOMATIC
MANUAL
1
2
3
4
56
1 - Manual – Select to put the tool in manual mode.
2 - Automatic – Select to put the tool in automatic mode.
3 - Tool Setup – Select to change torque units and set the date and time.
4 - Data Setup – Select to save data, view data or export data.
5 - Home Icon – Select to return to the “Home” screen.
6 - Back Arrow – Select to return to the previous screen.
Fig. 6

© 2016 Enerpac, All Rights Reserved 15
ETW Series Electric Torque Wrench
3.5.2 Manual Mode Screen
• To activate manual mode, select Manual from the “Home” screen. In manual mode the torque value can
be adjusted manually on the touchscreen control box or on the back of the tool. See Figure 24.
homeback
500
MANUAL
lbft
Recording
Start
12
3
4
5
1 - Torque Value – Displays the current torque value setting.
2 - Plus Icon – Select to increase the torque value.
3 - Minus Icon – Select to decrease the torque value.
4 - Start Recording – Pressing this button will start the recording of data that can be saved
and exported for maintenance records. Recordings include the bolt number, target torque,
achieved angle, pass/fail, wrench model, name of operator, and the date and time of
operation. Press the button again to stop the recording.
5 - Slider Button – Sliding the button to the right will increase the torque and sliding it to the left
will decrease the torque.
Fig. 7

16 © 2016 Enerpac, All Rights Reserved
ETW Series Electric Torque Wrench
3.5.3 Automatic Mode Screen
• Selecting Automatic from the “Home” screen will put the tool in automatic mode.
homeback
1 Flywheel - 3 x 500 lbf
2 5 x 650
SELECT AUTOMATIC PRESET
OK
Preset No.Description
5
1
2
3
4
1 - Pencil Icon – Select to activate the “Edit Automatic Preset” screen allowing the user to
make changes to preset programs.
2 - Plus Icon – Select to add new preset programs.
3 - Minus Icon - Select to remove preset programs.
4 - OK Icon – Select to save changes and return to the “Select Automatic Preset” screen.
5 - Preset Item – Touching the preset item once will highlight the item to allow editing of the
preset. Touching the item twice will select that item, will display the presets and will allow
you to run the preset.
Fig. 8

© 2016 Enerpac, All Rights Reserved 17
ETW Series Electric Torque Wrench
3.5.4 Automatic Preset Mode Screen
• This screen displays the preset values after the desired preset has been selected. The automatic preset
can be run from this screen.
homeback
350
400
nut
1
of
3
500 50
Automatic Preset Mode
Flywheel 3 x 500 lbf
lbft angle achieved angle
Recording
Start
1
2
6
7
3
45
8
9
1 - Fastener – Displays the number of fasteners to be tightened.
2 - Torque Step One – Displays the preset torque value required for this item to complete step
one.
3 - Torque Step Two – Displays the preset torque value required for this item to complete step
two.
4 - Torque Step Three – Displays the preset torque value required for this item to complete step
three. (Additional torque steps may be added as needed.)
5 - Angle – Displays the preset torque angle degree that will be performed to complete the
procedure. The angle setting (1 to 259 degrees) is optional but, when it is used, always
occurs after the final torque step.
6 - Start Recording – Pressing this button will start the recording of data that can be saved
and exported for maintenance records. Recordings include the bolt number, target torque,
achieved angle, pass/fail, wrench model, name of operator, and the date and time of
operation. For recordings made in automatic mode, the name and number of the preset are
also included. Press the button again to stop the recording.
7 - Recording Light – The light will flash when recording data.
8 - Minus Icon – Select to return to the previous torque steps.
9 - Plus Icon – Select to advance through the torque steps.
Fig. 9

18 © 2016 Enerpac, All Rights Reserved
ETW Series Electric Torque Wrench
3.5.5 Edit Automatic Preset Screen
• While in the “Select Automatic Preset” screen, select the automatic preset for editing, and touch the pencil
icon. The “Edit Automatic Preset” screen will then appear. Each setting may now be edited by touching
the desired setting, and then making the desired edits.
homeback
EDIT AUTOMATIC PRESET
OK
Torque
Steps lbft Angle
Flywheel - 3 x 500 lbf
Preset
Total Nuts
1
3
1
2
3
350
400
500 50
1
23
4
9
8
5
6
7
1 - Preset Number – This is the preset number shown at the “Select Automatic Preset” screen.
2 - Preset Description – This is the preset name shown at the “Select Automatic Preset” screen.
3 - Torque Value – This displays the current preset torque value for each step.
4 - Pencil Icon – The pencil is not functional on this screen.
5 - Plus Icon – Select to add torque steps. When a step is added it will automatically default to
the torque value of the currently highlighted step.
6 - Minus Icon – Select to subtract torque steps.
7 - OK Icon – Select to save changes and to return to the “Select Automatic Preset” screen.
8 - Torque Angle – Displays the desired angle of turn to be applied after the input torque steps
are achieved. Torque angle range is 1 to 259 degrees. Note that the angle setting on the final
bolt is optional.
9 - Total Nuts – Displays the current preset number of fasteners.
Fig. 10

© 2016 Enerpac, All Rights Reserved 19
ETW Series Electric Torque Wrench
3.5.6 Edit Preset Description Screen
• To change the description name of a preset, touch the preset name at the top of the “Edit Automatic
Preset” screen. The keyboard screen will pop up to allow you to edit the name.
• Touch on the preset name above the keyboard and then edit the description. When done, touch the OK
icon to save the changes or the X icon to exit the screen without saving the changes. After pressing either
icon, you will be returned to the “Edit Automatic Preset” screen.
OK
Flywheel - 3 x 500 lbf
1234567890
-=‹--
asdfgh jkl;’`
qwer tyuiop []\
zxcvbnm, ./
1
2
3
1 - Preset Description – Touch the description to edit the preset description.
2 - OK Icon – Touch the OK icon to save the changes and return to the “Edit Automatic Preset”
screen.
3 - X Icon – Touch the X icon to return to the “Edit Automatic Preset” screen without saving the
changes.
Fig. 11

20 © 2016 Enerpac, All Rights Reserved
ETW Series Electric Torque Wrench
3.5.7 Edit Preset Number Screen
• To change the current preset number, touch the preset number on the “Edit Automatic Preset” screen.
• The current preset number will be displayed in the box.
• Use the touch screen to edit the preset number and press OK to save the changes or the X icon to exit
the screen without saving the changes. You cannot use the same preset number more than once. An error
message will display if you attempt to use the same number more than once.
123
<
4
4
56
78
0
OK
9
Preset Number 0-999
1
2
3
4
1 - Preset Number – The box will display the current preset number.
2 - Keypad – Use the keypad to edit the current preset number.
3 - OK Icon – Touch the OK icon to save the changes and return to the “Edit Automatic Preset”
screen.
4 - X Icon – Touch the X icon to return to the “Edit Automatic Preset” screen without saving the
changes.
Fig. 12