ENFORCER ENHANCED MVE-AH1H1-42YQ User manual

4K
ENHANCED
HDMI
Long Range
Extender
MVE-AH1H1-42YQ
Installation Manual
The ENFORCER 4K ENHANCED HDMI Long Range Extender extends the range of HDMI signals
by using an active transmitter and receiver to send video and audio, RS-232, and bi-directional IR
over a single Cat5e/6 cable. It can send 1080p signals up to 492ft (150m) between the two units
with zero signal loss, while 4K2K/UHD HDMI signals can be transmitted up to 394ft (120m). A
single power supply can power both devices from either end of the installation.
 Extends 1080p up to 492ft (150m) and 4K2K up to 394ft (120m)
 Supports resolutions from 480i to 4K2K/UHD
 Supports 18Gbps video bandwidth
 Plug and play operation – comes as a complete set
 HDCP 2.2 / HDCP 1.4 and DVI 1.0 compliant
 Transmitter includes an HDMI loop output
 Analog stereo output on receiver
 Bi-directional IR, RS-232, and CEC pass-through
 Supports HDF, HDR10+, Dolby Vision, and HLG
 Includes one 24VDC power supply – set can be powered at either the transmitter or receiver
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries

4K ENHANCED HDMI Long Range Extender
2 SECO-LARM U.S.A., Inc.
Parts List
1x
Transmitter
1x
Receiver
1x
IR Transmitter
1x
IR Receiver
1x
24V
Power adapter
4x
IR Mounting clips
2x
3
-
Pin phoenix connector
1x
Manual
Specifications
Input video signal 3.3V
Input DDC signal 5Vp-p (TTL)
Maximum single link range 4K2K@60Hz
Deep color 48-bit
Video formats supported All HDMI 3D, HDCP 2.2
Audio formats supported
LPCM 2.0/2.1/5.1/6.1/7.1, Dolby Digital, Dolby TrueHD,
Dolby Digital Plus (DD+), DTS-ES, DTS HD Master, DTS HD-HRA,
DTS-X
L/R Audio formats PCM 2.0
Output video HDMI
Resolutions supported 4K2K@50/60Hz, 4K2K@30Hz, 1080p, 1080i, 720p, 720i, 480p, 480i
Range 1080p 492ft (150m)
4Kx2K 394ft (120m)
Video amplifier bandwidth 18Gbps
Video input connector HDMI Type A 19-pin female
Max. HDMI cable length (IN/OUT) 4K@60Hz, 16' (5m) / 4K@30Hz, 32' (10m) / 1080p@60Hz, 50' (15m)
Cat5e/6 wiring standard T568-B
IR Pass-through 20~60kHz
Operating voltage 24VDC
Power supply 1A@24VDC (1 adapter)
ESD protection
(human body model) ±8kV (air-gap discharge), ±4kV (contact discharge)
Current draw (both units total) 390mA
Operating humidity 20~90% (non-condensing)
Operating temperature 32°~104° F (0°~40° C)
Dimensions 51/2"x11/16"x29/16" (140x18x65 mm)
Weight Transmitter 5.6-oz (160g), Receiver 5.5-oz (155g)
Dimensions
Front Side
Both transmitter and
receiver have the same dimensions and the same front panel
.
11
/
16
"
(18mm)
51/2" (140mm) 29/16" (65mm)
Power LED Micro-USB port

4K ENHANCED HDMI Long Range Extender
SECO-LARM U.S.A., Inc. 3
Overview
Installation
1. Determine the location of the transmitter and receiver and how much Cat5e/6 cable is needed.
2. Connect the HDMI cable between the transmitter and source device.
3. Connect the HDMI cable between the receiver and the display.
4. Connect the Cat5e/6 cable between the receiver and transmitter.
5. Connect the included 24VDC power adapter to either the transmitter or receiver.
6. If any device will be controlled by the remote control:
a. Plug the IR transmitter into the IR-OUT of the extender
unit nearest the device to be controlled, pointing the IR
transmitter toward the device's IR window.
b. Plug the IR receiver into the IR-IN port of the other
extender unit so that the IR receiver will be easily visible to the remote control's signal.
NOTE: Maximum IR transmission distance of 26ft (8m) can only be achieved when the line of
sight is directly in line. At about 45° the distance may be reduced to 16ft (5m).
7. If desired, connect an RS-232 controller unit to the RS-232 terminal on the transmitter and
connect the remote device to be controlled to the RS-232 terminal on the receiver.
8. If desired, connect powered speakers to the Audio Out on the receiver.
9. If desired, connect a monitor to the HDMI Loop Out of the transmitter.
NOTES
 High-quality Cat5e/6 cables are
recommended, especially at longer distances.
 Premium high-speed HDMI cables are highly
recommended.
 Both Cat5e/6 and HDMI cable lengths should be kept within the maximums shown in Fig. 2.
Transmitter
Power input HDBT Out
Link
LED
Data
LED
HDMI Loop-out HDMI In IR In IR Out RS-232
Receiver
Power input HDBT In
Link
LED
Data
LED
HDMI Out Audio Out IR In IR Out RS-232
Fig. 2 – Maximum Cable Length Chart
Resolution 4K@60Hz 4K@30Hz 1080p@60Hz
Cat5e/6 394' (120m) 492' (150m)
HDMI 16' (5m) 32' (10m) 50' (15m)
Fig. 1 – HDBT Port LEDs
Steady On Flashing Off
Link
Good Poor None
Data
HDMI with
HDCP
HDMI
only
No HDMI
or HDCP

4K ENHANCED HDMI Long Range Extender
IMPORTANT
:
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local l
aws and statutes related to
monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or statutes.
California Proposition 65 Warning:
These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other
reproductive harm. For more information, go to www.P65Warnings.ca.gov.
WARRANTY:
This SECO
-
LARM product is warranted against defects in material and workmanship while used in normal service for
one
(
1
)
year from the date of sale
to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective p
art if the unit is returned, transportation prepaid, to
SECO-LARM. This Warranty is void if damage is caused by or attributed
to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper
or abnormal usage, or faulty installation, or if for any other reason SECO-
LARM determines that such equipment is not operating properly as a result of causes other
than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be lim
ited to the replacement or repair
only, at SECO-LARM’s option. In no event shall SECO-
LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any
kind to the purchaser or anyone else.
NOTICE:
The SECO
-
LARM p
olicy is one of continual development and improvement. For that reason, SECO LARM reserves the right to change specifications
without
notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2022
SECO-LARM U.S.A., Inc. All rights reserved.
Sample Application
NOTES:
 Only one power supply is used, either on the transmitter or receiver.
 User either the IR IN on the transmitter and IR OUT on the receiver to control the distant HDMI
display from the source, or the IR IN on the receiver and IR OUT on the transmitter to control the
source from the distant display area.
Troubleshooting
HDMI device does not
function correctly
 Use T568-B wiring standard
 Make sure the maximum lengths are not exceeded for either the HDMI or
Cat5e/6 cable used (see Fig. 1, pg. 3)
 Test the Cat5e/6 cable between the receiver and transmitter and make sure
it is functional
 Make sure that there are no problems with the HDMI source, HDMI cables,
or HDMI display by plugging the source directly into the display using an
HDMI cable
 Make sure that the transmitter and receiver are plugged into the correct units
 Make sure the HDMI source is compatible with the HDMI display
Transmitter
HDMI Matrix with
RS-232
HDMI
Display
HDMI
Display
AV Source
Receiver
Remote control for
distant HDMI
display
Remote control for
AV source
SECO-LARM ® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website:
www.seco
-
larm.com
Phone: [phone] | [phone] Email: [e-mail]
PICHN3
MI_MVE
-
AH1H1
-
42YQ_221019.docx