ENFORCER DE-S104Q User manual

High-Speed USB 2.0 1x4 Extender
DE-S104Q
Installation Manual
The ENFORCER High-Speed USB 2.0 1x4 Extender creates a one-to-one connection through
CAT5e/6/7 network cables, transmitting signals up to 492' (150m). It supports four (4) High-Speed
USB 2.0 ports and is compatible with most USB 2.0 devices making it a good choice for office,
security, audio/video, and medical facilities.
 Supports four (4) High-Speed USB 2.0 inputs and one (1) High-Speed USB 2.0 output
 Compatible with Cat5e/6/7 network cables
 Transmission range up to 492' (150m) with Cat6/7 cable
 Plug and Play
 Extend transmission further with Gigabit switch support
 Hot-Plug USB (auto-detects USB type — High-Speed, Full-Speed, and Low-Speed)

High-Speed USB 2.0 1x4 Extender
2 SECO-LARM U.S.A., Inc.
Parts List
1x
Transmitter
1x
Receiver
1x
USB Cable
1x
Power supply
1x
Manual
Specifications
Compliance USB 2.0
Maximum speed 480Mbps
Maximum
range
CAT5e Up to 328' (100m)
CAT6/6A/7 Up to 492' (150m)
Switch extension Supports Gigabit switches
USB Hot-Plug Yes
USB-A Transmitter One (1) output port
Receiver Four (4) input ports
Cable CAT5e, CAT6, CAT6A, CAT7
Power
supply
Transmitter Powered by device
Receiver 1A@5VDC
Power
consumption
Transmitter ≤2W
Receiver
Operating humidity 0~90% (non-condensing)
Operating temperature -4°~140° F (-20°~60° C)
Dimensions 3"x13/16"x21/2" (76x21x60 mm)
Weight Transmitter 4.3-oz (123g)
Receiver 4.5-oz (128g)
Overview
USB Host
CAT6 Out
13/16" (21mm)
21/2"
(60mm)
3" (76mm)
USB Hub
Reset
CAT6 In
Power
Both Receiver and Transmitter are the same size.

High-Speed USB 2.0 1x4 Extender
SECO-LARM U.S.A., Inc. 3
Installation
1. Connect the USB cable to the transmitter and the device you desire USB extension for.
2. Connect the network cable (CAT5e/6/6A/7) to the transmitter and receiver.
3. Plug the power supply into the receiver.
The four (4) ports on the receiver are now operational and ready for use.
Wiring Diagram
One-to-one connection
Switch relay connection
CAT5e up to 328' (100m)
CAT6e up to 492' (150m)
USB-A
Keyboard
Webcam
Mouse
USB Flash Drive
Receiver Transmitter
5VDC
Adapter
USB-A
Cable Legend
USB
-
A
CAT5e/6e
Power
PC
PC
USB-A
PC
Keyboard
Webcam
Mouse
USB Flash Drive
CAT5e up to 328' (100m)
CAT6e up to 492' (150m)
Transmitter
Gigabit switch
Receiver
5VDC
Ada
p
ter
USB-A
Cable Legend
USB
-
A
CAT5e
/6e
Power

High-Speed USB 2.0 1x4 Extender
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1)
THIS DEVICE MAY
NOT CAUSE HARMFUL INTERFERENCE AND (2)
THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is
permitted. Any change to the antenna
or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.
IMPORTANT:
Users and installers of this product are responsible for ensuring that the installation and configuration of this product com
plies with all national, state,
and local laws and codes. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.
California Proposition 65 Warning:
These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other
reproductive harm. For more information, go to www.P65Warnings.ca.gov.
WARRANTY:
This SECO
-
LARM product is warranted against defects in material and workmanship while used in normal service for
one
(
1
)
year from the date of sale
to the original customer. SECO-LARM’s o
bligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to
SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglec
t, repair or alteration, improper
or abnormal usage, or faulty installation, or if for any other reason SECO-
LARM determines that such equipment is not operating properly as a result of causes other
than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s
exclusive remedy, shall be limited to the replacement or repair
only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage o
f any
kind to the purchaser or anyone else.
NOTICE:
The SECO
-
LARM policy is one of continual development and improvement. For that reason, SECO
-
LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2022
SECO-LARM U.S.A., Inc. All rights reserved.
Troubleshooting
No response when device is connected.
 Check that the USB drivers are properly installed and
updated.
 Check that the network cable is properly connected.
 Reset the receiver by pushing the Reset button
Receiver is unstable when connected to
external web camera
 High-powered USB devices require an external power
source.
SECO-LARM ® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website:
www.seco
-
larm.com
Phone: [phone] | [phone] Email: [e-mail]
PICLN3
MI_DE-S104Q_221027.docx