ENFORCER MVE-AH1E1-01NQ User manual

®
MVE-AH1E1-01NQ
HDMI Extender over Single Cat5e/6
Manual
Features:

Extend HDMI over a single Cat5e/6 cable
 Supports resolutions from 480i to 1080p
with zero signal loss

Transmits up to 164ft (50m) at 1080p over
Cat5e/6 cable
 HDMI Loop output for local HDMI display

Plug and play operation – comes as a
complete set
 IR Pass-through for remote control
extension and operation
 EDID Management switch
 Two (2) 5VDC power supplies included
Up to 98
4
ft (300m)
Range
Up to
164ft
(50m)
Resolution
1080p
Single Cable
Cat5e/6
Operation
Plug
and
Play

ENFORCER HDMI Extender over Single Cat5e/6
2 SECO-LARM U.S.A., Inc.
Features:
Table of Contents:
The ENFORCER HDMI Extender over Single Cat5e/6 extends the range of traditional HDMI cabling
methods by using an active transmitter and receiver to send video and audio over a single Cat5e/6
cable. HDMI formats as large as 1080p can be transmitted up to 164ft (50m) between the two units
with zero signal loss by using integrated circuits in the receiver and transmitter. The extender also
supports HDMI loop output, EDID management settings, and one way IR control for remotely
controlling HDMI sources and displays.
Introduction:
Signal Strength – Active operation ensures that the signal strength will remain strong over the
length of the cable.
Distance – The HDMI Extender over Single Cat5e/6 is capable of providing a clear HDMI signal up
to 164ft (50m).
Formats Supported – The HDMI Extender over Single Cat5e/6 supports both progressive and
interlaced formats: 1080p/1080i/720p/576p/576i/480p/480i.
Plug and Play – The HDMI Extender over Single Cat5e/6 comes as a complete set consisting of a
transmitter and receiver, power supplies, and IR dongles.
Zero Signal Loss – Integrated circuits in the transmitter and receiver clean, buffer and amplify the
HDMI signal to prevent signal loss and ensure a clear signal regardless of the length of the cable.
IR Pass-Through – Send IR signals from the monitor to the source for discrete operation of devices.
EDID Management – Use Extended Display Identification Data (EDID) management settings to
match the display settings to the source device.
Introduction ............................................................................................................................................. 2
Table of Contents ................................................................................................................................... 2
Features .................................................................................................................................................. 2
Parts List ................................................................................................................................................. 3
Specifications .......................................................................................................................................... 3
Overview ................................................................................................................................................. 4
Status LEDs ............................................................................................................................................ 5
HDMI Loop Output .................................................................................................................................. 5
EDID Settings ......................................................................................................................................... 5
IR Pass-through ...................................................................................................................................... 6
Installation ............................................................................................................................................... 6
Sample Application ................................................................................................................................. 7
Troubleshooting ...................................................................................................................................... 8
Also Available from SECO-LARM ........................................................................................................... 8
Warranty ................................................................................................................................................. 8

ENFORCER HDMI Extender over Single Cat5e/6
SECO-LARM U.S.A., Inc. 3
1x Transmitter (MVE-AH1E1-01NTQ)
1x Receiver (MVE-AH1E1-01NRQ)
2x 5VDC Power adapters
1x IR Transmitter (with double-sided tape)
1x IR Receiver (with double-sided tape)
1x Manual
Parts List:
Input Video signal
3.3V
Input DDC signal
5Vp
-
p (TTL)
Maximum single link range
1080p
Deep color
24bit
Video formats supported
High
-
speed HDMI, HDCP 1.2
Audio formats supported
LPCM, Dolby
-
AC3, DTS7.1, DSD
Output video
HDMI
Resolutions
supported
1080p/1080i/720p/576p/576i/480p/480i
Range
–
1080p
Up to 164' (50m)
Video amplifier bandwidth
4.95
Gbps
Video input connector
HDMI Type A 19
-
pin female
Maximum input cable length
24AWG (15m), 26AWG (10m), 28AWG (5m)
Video output
connector
HDMI Type A 19
-
pin female
Maximum output cable length
24AWG (15m), 26AWG (10m), 28AWG (5m)
Cat5e/6
W
iring standard
T
-
568B
IR Pass
-
through frequency
30~60 kHz
Operating voltage
5VDC
Power supply
1A@5VDC (2 Adapters) (2.1mm plug)
ESD P
rotection
(human body model)
±8kV (Air-gap discharge), ±4kV (contact discharge)
Current draw
Transmitter
300mA@5VDC
Receiver
200mA@5VDC
Operating temperature
32°~104° F (0°~40° C)
Operating humidity
20~90% RH (No condensation)
Dimensions
3
1
/
8
"x
11
/
16
"x2
5
/
8
" (79
x
17x6
7 mm)
Weight
5.3
-
oz (150g) (Each)
Specifications:

ENFORCER HDMI Extender over Single Cat5e/6
4 SECO-LARM U.S.A., Inc.
Overview:
Transmitter MVE
-
AH1E1
-
01NTQ:
Receiver MVE
-
AH1E1
-
01NRQ:
5VDC Input
Cat5e/6 Port
25/8" (67mm)
IR Transmitter
port
EDID Switch
HDMI Input
HDMI Output
11/16"
(17
mm)
31/8"
(79mm)
21/4"
(57mm)
HDMI Output
25/8" (67mm)
Cat5e/6 Port
IR Receiver
Port
5VDC Input
11/16"
(17mm)
21/4"
(57mm)
31/8"
(79mm)

ENFORCER HDMI Extender over Single Cat5e/6
SECO-LARM U.S.A., Inc. 5
Status LEDs:
EDID Settings:
The MVE-AH1E1-01NQ includes an Extended Display Identification Data (EDID) management
switch to match the display settings to the source device. This setting is used when the display is
not properly displaying an image from the source device.
When in position 1 (default: position 1), the extender will copy the transmitter HDMI loop display
to the source.
When in position 2, the extender will copy the receiver HDMI display EDID to the source.
HDMI Loop Output:
The MVE-AH1E1-01NQ includes a secondary HDMI output on the transmitter unit. This HDMI
output can be used for local displays that are in the same location as the HDMI source.
EDID Switch HDMI Input HDMI Output
Position 1 Position 2
Located above either Cat5e/6 port are two LEDs indicating Power and Link status.
Link LED
Power LED

ENFORCER HDMI Extender over Single Cat5e/6
6 SECO-LARM U.S.A., Inc.
1. Determine the locations where the MVE-AH1E1-01NQ units will be wired as well as length of
Cat5e/6 cable necessary.
2. Connect the transmitter to the HDMI output of the source device.
3. Connect the Cat5e/6 cable to both the receiver and transmitter units.
4. Connect the receiver to the HDMI input of the display or other device.
5. Connect one 5VDC adapter to the transmitter and another to the receiver.
6. Determine which device, if any, will be controlled by the remote control. Install the IR
transmitter to the IR-TX port, pointing the IR transmitter at the device to be controlled. Install
the IR receiver to the IR-RX port of the other device, pointing the IR receiver to where the
remote control will be. Point the remote control at the IR receiver when in use. Use the
included double-sided tape to securely fasten the IR transmitter and IR receiver in the
correct positions.
7. Switch on the HDMI source and display to verify that the system is functioning properly.
NOTE: It may be necessary to move the EDID Switch to a different position if the system is
not displaying a correct image.
Installation:
IR Pass-Through:
The MVE-AH1E1-01NQ supports IR pass-through signals to allow for remote operation of the
source device from the display location. The IR transmitter and receiver support a frequency range
between 30~60 kHz.
IR Transmitter IR Receiver

ENFORCER HDMI Extender over Single Cat5e/6
SECO-LARM U.S.A., Inc. 7
Sample Application:
Cable Legend:
Power
IR
Cat5e/6
HDMI
Loc
al
Display
5VDC Adapter
HDMI Source
IR Transmitter
Remote
Display
5VDC Adapter
Remote
IR Receiver
Cat5e/6
Up to
164
' (
5
0m)

ENFORCER HDMI Extender over Single Cat5e/6
8 SECO-LARM U.S.A., Inc.
SECO-LARM
® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website:
www.seco
-
larm.com
Phone: (949) 261
-
2999 | (800) 662
-
0800
Email: sales@seco
-
larm.com
®
PICHN3
MI_MVE
-
AH1E1
-
01NQ_210319.docx
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-
LARM reserves the right to
change specifications without notice. SECO-
LARM is also not responsible for misprints. All trademarks are the property of
SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2021 SECO-LARM U.S.A., Inc. All rights reserved.
WARRANTY: This SECO-LARM product is warranted against defects in
material and workmanship while used in normal service for
one (1) year from the date of sale to the original customer. SECO-
LARM’s obligation is limited to the repair or replacement of any defective
part if the unit is returned, transportation prepaid, to SECO-
LARM. This Warranty is void if damage is caused by or attributed to acts of God,
physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or
if for any other
reason SECO-LARM determines
that such equipment is not operating properly as a result of causes other than defects in material and
workmanship. The sole obligation of SECO-
LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only,
at SECO-LARM’s option. In no event shall SECO-
LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
HDMI, the HDMI Logo and High-
Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
Troubleshooting:
Accessories:
HDMI device does not function correctly
 Use T568-B wiring standard
 Make sure the extender is powered on both sides
 Make sure the source and display are powered
 Test the Cat5e/6 cable between the receiver and the
transmitter to make sure it is functional
 Make sure there are no problems with the HDMI source,
HDMI cables, or HDMI display by plugging the source
directly into the display using an HDMI cable
Screen flickering or brief image loss
 Use a higher grade of twisted pair category cable
(Cat6 is recommended)
 Switch the source device to a lower HDMI output
(i.e., 1080p to 1080i)
 Power down the unit then move the EDID switch to the
opposite position and re-power the unit
 Restart the handshake process by powering everything
down then powering up and connecting each device in
succession starting with the HDMI source
High
-
Speed
HDMI Cables
MC-1130-xxFQ
California Proposition 65 Warning:
These products may contain chemicals which are known to the State of California to cause cancer and
birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.