ENFORCER MVE-AH030AQ User manual

MVE-AH030AQ
Basic HDMI Extender over Single Cat5e/6
Manual
•Extend HDMI over a single Cat5e/6
cable
•Supports resolutions from 480i to 1080p
with zero signal loss
•Transmits up to 196ft (60m) at 1080p
over Cat5e/6 cable
®
IMPORTANT: This product is designed to extend an HDMI signal over Cat5e/6. This
product is not to be used to bypass any copy protection or other content protection system.
All usage of this product shall conform to the license that comes with the content.
•Plug and play operation – comes as a
complete set
•Bi-directional IR for remote control
extension
•EDID management setting
•Two (2) 5VDC power supplies included
Up to
196ft
(60m)
Cat5e/6
Plug
Play
and
Operation
Single Cable
1080p Resolution
®

ENFORCER Basic HDMI Extender over Single Cat5e/6
2SECO-LARM U.S.A., Inc.
Introduction:
The ENFORCER Basic HDMI Extender over Single Cat5e/6 extends the range of traditional HDMI cabling
methods by using an active transmitter and receiver to send video and audio over a single Cat5e/6 cable.
HDMI formats as large as 1080p can be transmitted up to 196ft (60m) between the two units with zero signal
loss by using integrated circuits in the receiver and transmitter. The extender also supports bi-directional IR
control for remotely controlling HDMI sources and displays.
Features:
•Signal Strength – Active operation ensures that the signal strength will remain strong over the length
of the cable.
•Distance – The Basic HDMI Extender over Single Cat5e
/6 is capable of providing a clear HDMI signal up to
196ft (60m).
•Formats Supported – The Basic HDMI Extender over Single Cat5e/6 supports both progressive and
interlaced formats: 1080p/1080i/720p/480p/480i.
•Plug and Play – The Basic HDMI Extender over Single Cat5e/6 comes as a complete set consisting of a
transmitter and receiver, power supplies, and IR dongles.
•Zero Signal Loss – Integrated circuits in the transmitter and receiver clean, buffer and amplify the HDMI
signal to prevent signal loss and ensure a clear signal regardless of the length of the cable.
•Bi-directional IR – Send IR signals from the source to the monitor or from the monitor to the source for
discrete operation of devices.
•EDID Management – Eliminate sync issues by choosing from STD EDID (1080p/60Hz, 2CH audio) or TV
EDID (copying the TV EDID information to the HDMI source).
Specifications:
Parts List:
1x Transmitter
1x Receiver
2x 5VDC Power adapters
1x Manual
1x IR Transmitter (w/ double sided tape)
1x IR Receiver (w/ double sided tape)
Model Number
MVE-AH030AQ
Input Video signal
3.3V
Input DDC signal
5Vp-p (TTL)
Maximum single link range
1080p
Deep color
24bit
Video formats supported
High-speed HDMI, HDCP 1.2
Audio formats supported
LPCM, Dolby-AC3, DTS7.1, DSD
Output video
HDMI
Resolutions supported
1080p/1080i/720p/576p/576i/480p/480i
Range – 1080p
Cat6
Up to 196' (60m)
Cat5e
Up to 98' (30m)
Video amplifier bandwidth
1.65Gbps
Video input connector
HDMI Type A 19-pin female
Maximum input cable length
24AWG (15m), 26AWG (10m), 28AWG (5m)
Video output connector
HDMI Type A 19-pin female
Maximum output cable length
24AWG (15m), 26AWG (10m), 28AWG (5m)
Cat5e/6 wiring standard
T-568B
Operating voltage
5VDC
Power supply
1A@5VDC (2 adapters) (2.1mm plug)
ESD protection (human body model)
±8kV (air-gap discharge), ±4kV (contact discharge)
Current draw
Transmitter
550mA@5VDC
Receiver
450mA@5VDC
Operating temperature
32°~104° F (0°~40° C)
Operating humidity
20~90% RH (no condensation)
Dimensions
33/16”x115/16”x1” ( 81x49x25 mm)
Weight
5.3-oz (150g) (each)

ENFORCER Basic HDMI Extender over Single Cat5e/6
SECO-LARM U.S.A., Inc. 3
Overview:
IR Tx
5VDC
Input
Cat5e/6
Input
Installation:
1. Determine the locations where the MVE-AH030AQ units will be wired as well as how much Cat5e/6 cable is necessary.
2. Connect the transmitter to the HDMI output of the source device.
3. Connect the Cat5e/6 cable to both the receiver and transmitter units.
Note: For maximum range use Cat6 cable.
4. Connect the receiver to the HDMI input of the display or other device.
5. Connect one 5VDC adapter to the transmitter and another to the receiver.
6. Determine which device, if any, will be controlled by the remote control. Install the IR transmitter to the IR-TX port,
pointing the IR transmitter at the device to be controlled. Install the IR receiver to the IR-RX port of the other device,
pointing the IR receiver to where the remote control will be. Point the remote control at the IR receiver when in use. Use
the included double-sided tape to securely fasten the IR transmitter and IR receiver in the correct positions.
7. Switch on the HDMI source and display to verify that the system is functioning properly.
Note: It may be necessary to move the EDID Switch to a different position if the system is not displaying a correct image.
Sample Application:
Transmitter:
HDMI
Output
Cable Legend:
Cat5e/6
Power
IR
HDMI
HDMI Source
Remote
Display
5VDC Adapter
IR Tx
Remote
IR Rx
Receiver:
IR Rx
Status LED
HDMI Input
Status
LED
5VDC
Input
IMPORTANT: This product is designed to extend an HDMI signal over Cat5e/6. This product is not to be used to bypass any copy
protection or other content protection system. All usage of this product shall conform to the license that comes with the content.
IR Tx
IR Rx
EDID
Switch
Cat5e/6
Output
Receiver
Basic HDMI Extender over Cat5e/6
Transmitter
Basic HDMI Extender over Cat5e/6
EDID
5VDC Adapter

ENFORCER Basic HDMI Extender over Single Cat5e/6
4SECO-LARM U.S.A., Inc.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right
to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2015 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole
or in part, without the written permission of SECO-LARM.
WARRANTY:
This SECO-LARM product is warranted against defects in material and workmanship while used in
normal service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s
obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to
SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or
abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason
SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material
and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the
replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral,
incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.
SECO-LARM®U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
PICHN3
Tel: [phone] | [phone]
Email: [e-mail]
MI_MVE-AH030AQ_151217
.docx
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
Troubleshooting:
HDMI d
evice does not function correctly
•Use T568-B wiring standard.
•Make sure the extender is powered on both sides.
•Make sure the source and display are powered.
•Test the Cat5e/6 cable between the received and the
transmitter to make sure it is functional.
•Make sure there are no problems with the HDMI source,
HDMI cables, or HDMI display by plugging the source directly
into the display using an HDMI cable.
Also Available from SECO-LARM
®
:
HDMI Extender over
Single Cat5e/6
HDMI Extender over
Dual Cat5e/6
High-Speed HDMI Cables
Screen flickering or brief image
loss
•Use a higher grade of twisted pair category cable (Cat6 is
recommended).
•Switch the source device to a lower HDMI output (i.e. 1080p
to 1080i)
•Power down the unit then move the EDID switch to the
opposite position and re-power the unit.
•Restart the handshake process by powering everything down
then powering up and connecting each device in succession
starting with the HDMI source.
MVE-AH030Q
MVE-AH010Q
MC-1102-xxxQ