ENFORCER SECO-LARM NR-P102E-TQ User manual

Gigabit PoE Extenders
Installation Manual
NR-P102E-TQ NR-P101E-TQ NR-P401E-TQ
Model PoE Standards PoE Out IP rating
NR-P101E-TQ IEEE 802.3af, IEEE 802.3at 1 IP66*
NR-P102E-TQ IEEE 802.3af, IEEE 802.3at, IEEE 802.3bt (4 pairs, 90W) 1 Indoor†
NR-P401E-TQ IEEE 802.3af, IEEE 802.3at, IEEE 802.3bt (4 pairs, 60W) 4 Indoor†
*With weather-resistant UTP cable †Can be used outdoors with an IP66 sealed box and weather-resistant UTP cables
 Extends the range of PoE devices an additional 328ft (100m) with Cat5e cables or higher
 Maximum extended range of up to 984ft (300m) using two extenders
 Connects 10/100/1000BASE-T PoE devices including IP cameras, IP access control, VOIP,
IP speakers/intercoms, etc.
 Supports up to gigabit transmission rates
 Passive operation – no external power required and easy plug-and-play installation
 Automatically detects PoE equipment and protects from damage due to faulty installation
 Surge protection for both data and power ports
NR-P101E-TQ:
 IP66 Weatherproof with weather-resistant UTP cable
NR-P401E-TQ:
 4 Output ports for up to 4 PoE devices

Gigabit PoE Extenders
2 SECO-LARM U.S.A., Inc.
Parts List
All
1x
PoE Extender
1x
Manual
NR
-
P101E
-
TQ
includes
2x
End caps
NR
-
P401E
-
TQ
includes
2x
Wall
-
mount brackets
2x
Wall
-
mounting screws
2x
Plastic wall anchors
4x
Extender bracket mounting screws
Specifications
Model NR-P101E-TQ NR-P102E-TQ NR-P401E-TQ
Connections PoE In 1x Weather-resistant RJ45
1x Shielded RJ45
PoE Out 1x Weather-resistant RJ45 1x Shielded RJ45 4x Shielded RJ45
Power Input Power Output
Transmission
range*
656ft
(200m)
15W 11.1W 11.1W 4-port<11.1W
30W 19W 19W 4-port<19W
60W N/A 40W 4-port<40W
90W N/A 48W 4-port<40W
948ft
(300m)
15W 6.8W 6.8W N/A
30W 15W 15W N/A
60W N/A 30W N/A
90W N/A 30W N/A
Data link Both pin 1/2, 3/6 and 4/5, 7/8
Power link Pin 1/2(+), 3/6(–)
up to 25W
Pin 1/2 (–), 3/6 (+) and
4/5 (+), 7/8 (–), up to 85W
Pin 1/2(+), 3/6(–) up to
12W/4 PSE, 25W/2 PSE
Network cables Weather-resistant Cat5e
or higher Shielded Cat-5e or higher
Ethernet speed 10/100/1000 Mbps half/full duplex
PoE standard IEEE 802.3af,
IEEE 802.3at
IEEE 802.3af,
IEEE 802.3at,
IEEE 802.3bt
(4 pairs, 90W)
IEEE 802.3af,
IEEE 802.3at,
IEEE 802.3bt
(4 pairs, 60W)
LED
Indicators
Power
None
Green = PoE power in Yellow
PoE Green = PoE switch on Yellow
Data link LAN x2 green
(steady = link,
flashing = transmit)
Green, steady
Data transmit Green flashing
IP Rating
IP66 (with
weather-resistant UTP
cable)
None†
Operating humidity 90% (maximum, non-condensing)
Operating temperature -13°~101° F (-25°~55° C) 14°~122° F (-10°~50° C) 14°~113° F (-10°~45° C)
Dimensions 71/4"x13/4"x13/4"
(185x45x45 mm)‡
39/16"x21/16"x11/8"
(90x52x29 mm)
411/16"x11/8"x33/8"
(119x28x85 mm)
Weight 8-oz (227g) 7.2-oz (204g) 8.8-oz (250g)
*The maximum range depends on the actual operating conditions, PoE device power requirements, and the type of PoE
device. Cat5e/6 Ethernet cables are recommended.
†The NR-P401E-TQ and NR-P102E-TQ can be used outdoors with an IP66 sealed box and weather-resistant UTP cables.
‡Including endcaps

Gigabit PoE Extenders
SECO-LARM U.S.A., Inc. 3
Overview
Sample CCTV Application
PoE In
21/16"
(52mm)
11/8"
(29mm)
39/16" (90mm)
LAN Input
indicator
PoE Output
switch
Input power
indicator
Ground
screw
PoE Out
PoE Output
indicator
LAN Output
indicator
NR-P102E-TQ
11/8"
(28mm)
13/4"
(45mm)
NR-P101E-TQ
PoE In
NR-P401E-TQ
71/4" (185mm)
411/16" (119mm)
13/4" (45mm)
33/8"
(85mm)
PoE Out
PoE
Out
PoE
In
PoE INPoE OU T1 2 3 4
Link/ActPowerPoE Link/Act
Gig abit PoE
Extender
OUTIN
IN OU T
Gigabit PoE Extender
Mounting tabs
Bracket
mounting holes
PoE Camera or other
PoE devices
Cat5e/6 cable
up to 328ft
(100m)
PoE source
Cat5e/6 cable
up to 328ft
(100m)
NR-P102E-TQ shown

Gigabit PoE Extenders
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1)
THIS DEVICE MAY
NOT CAUSE HARMFUL INTERFERENCE AND (2)
THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitt
ed. Any change to the antenna
or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.
IMPORTANT
:
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local l
aws and statutes related to
monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or statutes.
IMPORTANT:
Users and installers of this product are responsible for ensuring that the installation and configuration of this product com
plies with all national, state,
and local laws and codes. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.
California Proposition 65 Warning:
These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other
reproductive harm. For more information, go to www.P65Warnings.ca.gov.
WARRANTY:
This SECO
-
LARM product is warranted against defects in material and workmanship while used in normal service for
one
(
1
)
year from the date of sale
to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepa
id, to
SECO-LARM. This Warranty is void if damage is caused by or attributed
to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper
or abnormal usage, or faulty installation, or if for any other reason SECO-
LARM determines that such equipment is not operating properly as a result of causes other
than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s
exclusive remedy, shall be limited to the replacement or repair
only, at SECO-LARM’s option. In no event shall SECO-
LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any
kind to the purchaser or anyone else.
NOTICE:
The SECO
-
LARM policy is one of continual development and improvement. For that reason, SECO LARM reserves the right to change specific
ations without
notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2023
SECO-LARM U.S.A., Inc. All rights reserved.
Installation
1. Determine the proper location for mounting the extender between the PoE power source and
the PoE camera, ensuring that neither cable exceeds 328ft (100m) in length.
2. Mount the extender (except NR-P401E-TQ) with 4 screws (not included) and the mounting tabs.
3. NR-P401E-TQ – Attach the mounting brackets to the extender, with the included bracket
mounting screws. Drill holes and attach the extender/bracket assembly to the desired location
using the two wall mounting screws and, if needed, the plastic wall anchors.
4. Ensure that power to the PoE power source and all PoE devices is off.
5. Connect the cables from the PoE power source to the PoE In port of the extender.
6. Connect the cables from the PoE cameras to the PoE Out port of the extender.
7. NR-P102E-TQ – Connect a ground wire with resistance less than 0.5Ω to the grounding screw
and move the Extender's PoE output switch to ON.
8. Turn on the PoE power source and wait up to one minute for the devices to start and establish
connections.
9. Test to ensure that all devices are working properly.
Troubleshooting
PoE device doesn't
function properly
 Ensure that all devices are turned on
 Ensure that the PoE device is functioning by plugging it directly into the PoE
switch, computer, etc.
 Double-check that the cables were connected properly
 Run a continuity test on all wires in the cable
 Equipment at both ends must be at the same link speed, 10BASE-T with
10BASE-T, 100BASE-T with 100BASE-T, etc.
 Replace with a higher-grade cable for better performance
 Ensure that cable lengths are within the allowable range and consistent with
the remote PoE device power consumption and reduce cable length as needed
 No more than 2 PoE extenders may be used
 Check that power consumption is within the specifications
SECO-LARM ® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website:
www.seco
-
larm.com
Phone: [phone] | [phone] Email: [e-mail]
PICSN7
MI_NR-Px0xE-TQ_230908.docx