EnGenius EWS650AP User manual

Quick Installation Guide
EnGenius Europe | Veldzigt 28, 3454 PW De Meern,
Netherlands | 0900-WIFIABC | www.wiabc.com Disclaimer: Information may be subject to changes without prior notication. Follow us
https://www.linkedin.com/company/engeniuseurope
https://plus.google.com/+EngeniusEuropeBVDeMeern
https://www.youtube.com/user/engeniuseuropebv
https://twitter.com/engeniuseu
EWS650AP
Package contents
- Managed indoor access point
- Power adapter
- RJ-45 Ethernet cable
- Mounting bracket
- Mounting kit
- T-Rail mounting kit
Minimum requirements
- Broadband Internet service (Cable or DSL modem)
- Internet browser (Internet Explorer, Safari, Firefox, Chrome)
- EnGenius wireless management L2 switch (To use with EWS-series
management switches)
Connecting the access point
Step 1: Connect one end of the Ethernet cable into an Ethernet port on the front
panel of the EnGenius wireless management switch and the other end to the
Ethernet port on the computer.
Step 2: Connect another Ethernet cable into the LAN port of the managed
access point and the other end to the Ethernet port on the wireless management
switch. With the wireless management switches, the managed access point is
able to obtain proper assigned IP address for further configurations.
IP Adress configuration
Step 1: Once your computer is on, ensure that your
TCP/IP is set to ‘On’ or ‘Enabled’. Open ‘Network
Connections’ and then click ‘Local Area Connection’.
Select ‘Internet Protocol Version 4’ (TCP/IPv4).
Step 2: If your computer is already on a network,
ensure that you have set it to a static IP address on
the interface. (Example: 192.168.1.10 and the
subnet mask-address as 255.255.255.0.)
Management switch setup
Step 1: Open a web browser on your computer.
In the adress bar of the web browser, typ in 192.168.0.239 and choose enter.
Step 2: A login screen will appear. By default, the username is admin and the
password is password. Enter the current username and password of the
wireless management switch and then click ‘Login’.
Step 3: The EnGenius wireless management switch user interface will appear.
Make sure the controller state is set to ‘Enabled’.

Quick Installation Guide
EnGenius Europe | Veldzigt 28, 3454 PW De Meern,
Netherlands | 0900-WIFIABC | www.wiabc.com Disclaimer: Information may be subject to changes without prior notication. Follow us
https://www.linkedin.com/company/engeniuseurope
https://plus.google.com/+EngeniusEuropeBVDeMeern
https://www.youtube.com/user/engeniuseuropebv
https://twitter.com/engeniuseu
EWS650AP
Wall mounting
A. Attach the location sticker to the desired location on the wall and use a 6mm
drill bit to drill the two holes.
B. Insert the screw anchors into the 6mm holes then insert the screws and tighten.
C. Align the access point over the keyhole mounting slots and insert both screw
heads into each keyhole slot. Then slide the access point downward until it’s
firmly hooked in place.

Quick Installation Guide
EnGenius Europe | Veldzigt 28, 3454 PW De Meern,
Netherlands | 0900-WIFIABC | www.wiabc.com Disclaimer: Information may be subject to changes without prior notication. Follow us
https://www.linkedin.com/company/engeniuseurope
https://plus.google.com/+EngeniusEuropeBVDeMeern
https://www.youtube.com/user/engeniuseuropebv
https://twitter.com/engeniuseu
EWS650AP
Pole mounting
A. Use a flathead screwdriver to unfasten the screw on the pole mounting ring
and thread it through the middle tab on the rear of the access point.
B. Mount the access point onto the pole by wrapping the ring around the pole
and fastening the screw.

Quick Installation Guide
EnGenius Europe | Veldzigt 28, 3454 PW De Meern,
Netherlands | 0900-WIFIABC | www.wiabc.com Disclaimer: Information may be subject to changes without prior notication. Follow us
https://www.linkedin.com/company/engeniuseurope
https://plus.google.com/+EngeniusEuropeBVDeMeern
https://www.youtube.com/user/engeniuseuropebv
https://twitter.com/engeniuseu
EWS650AP
Stand-alone access point Installation
Connecting the access point
Step 1: Connect one end of the Ethernet cable into the LAN port of the access
point and the other end to the Ethernet port on the computer.
Step 2: Connect the power adapter to the DC-IN port of the access point and
plug the other end in to an electrical outlet.
Note: The access point supports both IEEE802.3at PoE (Power-over-Ethernet) or
the included power adapter. You may use either one as the power source.
DO NOT use both at the same time.
IP address configuration
Step 1: Once your computer is on, ensure that your TCP/IP is set to ‘On’ or
‘Enabled’. Open ‘Network Connections’ and then click ‘Local Area
Connection’. Select ‘Internet Protocol Version’ (TCP/IPv4).
Step 2: If your computer is already on a network, ensure that you have set it
to a static IP address on the interface. (Example 192.168.1.10 and the subnet
mask-address as 255.255.255.0).
Access point setup
Step 1: Open a web browser on your computer. In the address bar of the web
browser, typ in 192.168.1.1 and choose Enter.
Step 2: A login screen will appear. By default, the username of the access point
is admin and the password is admin. Enter the current username and
password of the access point and then click ‘Login’.
Step 3: The EnGenius access point user interface will appear. This device can
operate in the following modes: Access point, WDS AP and WDS bridge.
Switch modes by selecting the operation mode under ‘Network’, ‘Wireless’ tab.