EnGenius Neutron EWS320AP User manual

Quick Installation Guide
EnGenius Europe | Veldzigt 28, 3454 PW De Meern,
Netherlands | 0900-WIFIABC | www.wiabc.com Disclaimer: Information may be subject to changes without prior notication. Follow us
https://www.linkedin.com/company/engeniuseurope
https://plus.google.com/+EngeniusEuropeBVDeMeern
https://www.youtube.com/user/engeniuseuropebv
https://twitter.com/engeniuseu
EWS320AP
Package contents
- Managed indoor access point
- Power adapter
- RJ-45 Ethernet cable
- Mounting bracket
- Mounting kit
- T-Rail mounting kit
Minimum requirements
- Broadband Internet service (Cable or DSL modem)
- Internet browser (Internet Explorer, Safari, Firefox, Chrome)
- EnGenius wireless management L2 switch (To use with EWS-series
management switches)
Connecting the access point
Step 1: Connect one end of the Ethernet cable into an Ethernet port on the front
panel of the EnGenius wireless management switch and the other end to the
Ethernet port on the computer.
Step 2: Connect another Ethernet cable into the LAN port of the managed
access point and the other end to the Ethernet port on the wireless management
switch. With the wireless management switches, the managed access point is
able to obtain proper assigned IP address for further configurations.
IP adress configuration
Step 1: Once your computer is on, ensure that your
TCP/IP is set to ‘On’ or ‘Enabled’. Open ‘Network
Connections’ and then click ‘Local Area Connection’.
Select ‘Internet Protocol Version 4’ (TCP/IPv4).
Step 2: If your computer is already on a network,
ensure that you have set it to a static IP address on
the interface. (Example: 192.168.1.10 and the
subnet mask address as 255.255.255.0.)
Management switch setup
Step 1: Open a web browser on your computer.
In the adress bar of the web browser, typ in 192.168.0.239 and choose enter.
Step 2: A login screen will appear. By default, username is admin and the
password is password. Enter the current username and password of the
wireless management switch and then click ‘Login’.
Step 3: The EnGenius wireless management switch user interface will appear.
Make sure the controller state is set to ‘Enabled’.

Quick Installation Guide
EnGenius Europe | Veldzigt 28, 3454 PW De Meern,
Netherlands | 0900-WIFIABC | www.wiabc.com Disclaimer: Information may be subject to changes without prior notication. Follow us
https://www.linkedin.com/company/engeniuseurope
https://plus.google.com/+EngeniusEuropeBVDeMeern
https://www.youtube.com/user/engeniuseuropebv
https://twitter.com/engeniuseu
EWS320AP
Adding managed access point (Through EnGenius wireless
management switch GUI)
Step 1: All managed access point(s) connected to the same network as the
wireless management switch will appear on the right side of the screen, under
the access point ‘under approval’ list. Locate and select the managed access
point by checking the box and click ‘Allow’ to manage the device.
Step 2: You may configure your managed access point(s) after you successfully
connected to the wireless management switch through its GUI.
Configuring managed access point (Through EnGenius wireless
management switch GUI)
Step 1: Configure managed access
point(s) through the GUI interface from
the switch for WLAN settings under
‘device management’.
Step 2: Add managed access point(s)
to specific access point cluster to save
repetitive configuration tasks.
Step 3: Users may create several clusters simultaneously to accommodate their
deployments under access point clusters.
Step 4: For distinct settings, EnGenius wireless management switches still offer
individual managed access point customization for cluster members such as
different channels that best adapt your local WLAN deployments.
Step 5: Upon successful connection and setup, users can go through different
sections on the web management pages to unleash managed access point(s) full
features for your WLAN deployment and perfomance monitoring.

Quick Installation Guide
EnGenius Europe | Veldzigt 28, 3454 PW De Meern,
Netherlands | 0900-WIFIABC | www.wiabc.com Disclaimer: Information may be subject to changes without prior notication. Follow us
https://www.linkedin.com/company/engeniuseurope
https://plus.google.com/+EngeniusEuropeBVDeMeern
https://www.youtube.com/user/engeniuseuropebv
https://twitter.com/engeniuseu
EWS320AP
Mounting the access point
The AP can be ceiling mounted or wall mounted depending on the setup.
To attach the access point to a ceiling or
wall using the mounting bracket:
Step 1: Attach the mounting bracket to the wall or
ceiling using the provided mounting kit.
Step 2: Insert the provided short screws into the
mounting holes. Make sure there’s enough space
between the screws and unit for the mounting
bracket. If extra space is required, use the provided
spacers and long screws from the T-Rail
mounting kit.
Step 3: Mount the access point to the mounting bracket by rotating the unit
clockwise about 90 degrees to secure it in place.
To attach the access point to a ceiling using T-Rail connectors:
Step 1: Attach the T-Rail connectors to the bottom cover of the access point
using the provided short screws. Use appropriate size T-rail connectors
(15/16” or 9/16”). If extra space is required to accommodate drop ceiling
tiles, use the provided spacers and long screws.
Step 2: Line up the connected T-rail connectors with an appropriately sized rail
and press the unit onto the rail until it snaps into place.
Note: To protect your access point, use the Kensington security slot to attach a
cable lock (cable lock is not included).

Quick Installation Guide
EnGenius Europe | Veldzigt 28, 3454 PW De Meern,
Netherlands | 0900-WIFIABC | www.wiabc.com Disclaimer: Information may be subject to changes without prior notication. Follow us
https://www.linkedin.com/company/engeniuseurope
https://plus.google.com/+EngeniusEuropeBVDeMeern
https://www.youtube.com/user/engeniuseuropebv
https://twitter.com/engeniuseu
EWS320AP
Stand-alone access point Installation
Connecting the access point
Step 1: Connect one end of the Ethernet cable into the LAN port of the access
point and the other end to the Ethernet port on the computer.
Step 2: Connect the power adapter to the DC-IN port of the access point and
plug the other end in to an electrical outlet.
Note: The access point supports both IEEE802.3at PoE (Power-over-Ethernet) or
the included power adapter. You may use either one as the power source.
DO NOT use both at the same time.
IP address configuration
Step 1: Once your computer is on, ensure that your TCP/IP is set to ‘On’ or
‘Enabled’. Open ‘Network Connections’ and then click ‘Local Area
Connection’. Select ‘Internet Protocol Version’ (TCP/IPv4).
Step 2: If your computer is already on a network, ensure that you have set it
to a static IP address on the interface. (Example 192.168.1.10 and the subnet
mask-address as 255.255.255.0)
Access point setup
Step 1: Open a web browser on your computer. In the address bar of the web
browser, typ in 192.168.1.1 and choose enter.
Step 2: A login screen will appear. By default, the username of the access point
is admin and the password is admin. Enter the current username and
password of the access point and then click ‘Login’.
Step 3: The EnGenius access point user interface will appear. This device can
operate in the following modes: Access point, WDS AP and WDS bridge.
Switch modes by selecting the operation mode under ‘Network’, ‘Wireless’ tab.