EnGenius EOC1650 User manual

EOC1650 Quick Start
Guide
Wireless Access Point & Client Bridge
Quick Start Guide v.1.0
Refer to User’s Manual for complete instructions 1
EOC1650 is a revolutionary product consists of conciseness, quality,
and flexibility. It comes with 7dBi internal antenna and upgradable
SMA interface provides a customizable interface for enhanced
network coverage. Attached suction cup allows quick installation on
window or smooth surface.
Operation mode provides Access Point / Client Bridge /Client Router
and high bandwidth up to 54Mbps. It features high transmitted
output power and high receivable sensitivity. High output power and
high sensitivity extends range and coverage to reduce the roaming
between Access Points to ensure a stable wireless connection and
reduce the expense of equipment.
IP Address Configuration
The default IP address of the device is
192.168.1.1.In order to log into this
device, you must first configure the
TCP/IP settings of your PC/Notebook.
1. In the control panel, double click
Network Connections and then
double click on the connection of
your Network Interface Card (NIC).
You will then see the following
screen.
2. Select
Internet Protocol (TCP/IP) and
then click on the Properties button.
This will allow you to configure the
TCP/IP settings of your PC/Notebook.
3. Select Use the following IP Address
radio button and then enter the IP
address (192.168.1.21) and subnet
mask (255.255.255.0). Ensure that the
IP address and subnet mask are on
the same subnet as the device.
4. Click on the OK button to close this
window, and once again to close
LAN properties window.
Logging In
1. To configure the device through the
web-browser, enter the IP address of
the Bridge (default: 192.168.1.1)
into the address bar of the
web-browser and press Enter.
2. After connecting to the IP address,
the web-browser will display the login
page. Specify admin as the default
User Name and Password, and then
click on the Login button.
Administration
1. Click on the Administration link under
the Management section. This option
allows you to create a new user
name and password for the device.
For security it is highly recommended
for security reasons.
2. Name: Specify a user name into the
first field.
3. Password: Specify a password into
this field and then re-type the
password into the Confirm Password
field. Then click on the Apply button.
4. Click on the Apply button to save
the changes.
System Properties

EOC1650 Quick Start
Guide
Wireless Access Point & Client Bridge
Quick Start Guide v.1.0
Refer to User’s Manual for complete instructions 2
1. Click on the System Properties link on
the System section. This feature
allows you to configure the device
as an Access Point or Repeater.
2. Device Name: Specify a name for
the device – this is not the SSID.
3. Country/Region: Select the region
from the drop-down list.
4. Operation Mode: Select Access Point
or Client Bridge radio button.
5. Click on the Apply button to save
the changes.
IP Settings
1. Click on the IP Settings link on the
System section. This feature allows
you to configure the LAN
interface using a static IP address
or as a DHCP client. This IP
address is also used to access the
web-based interface.
2. IP Network Setting: Select Obtain
an IP address automatically
(DHCP) radio button if the Access
Point is connected to a DHCP
server. This will allow the Access
Point to pass IP addresses to the
clients associated with it.
You may select Specify an IP
Address radio button if you would
like the device to use a static IP
address. In this case, you would
be required to specify an IP
address, subnet mask, and default
gateway IP address.
3. IP Address: Specify an IP address
4. IP Subnet Mask: Specify the
subnet mask for the IP address
5. Default Gateway: Specify the IP
address of the default gateway.
6. Click on the Apply button to save
the changes.
Note: If you change the IP address here,
you may need to adjust your PC’s
network settings to access the network
again.
Wireless Network & Security
1. Click on the Wireless Network link
on the Wireless section. This
feature allows you to configure
the wireless mode, channel, SSID,
and security settings.
2. Wireless Mode: Depending on the
type of wireless clients that are
connected to the network, you
may select B, G, or B/G-mixed.
3. Channel: Select a channel from
the drop-down list. The channels
available are based on the
country’s regulation.
4. You may configure up to four
different wireless profiles. Click on
the Edit button to modify the
profile and place a check in the
Enable box to activate the profile.
5. SSID: The SSID is a unique named
shared amongst all the points of
the wireless network. The SSID must
be identical on all points of the
wireless network and cannot
exceed 32 characters.
6. VLAN ID: If you have enabled
VLAN tagging on your network,
specify the VLAN tag ID.
7. Suppressed SSID: Place a check in
this box if you would like to hide
the SSID. By enabling this feature,
wireless clients will not be able to
scan this access point in a site
survey.
8. Station Separator: This is also
known as layer 2 isolation. Clients
connected to this Access Point will
not be able to directly
communicate with each other.
9. Security Mode: By default, the
security is disabled. Refer to the
user’s Manual to configure the
security features such as WEP,
WPA, WPA-PSK, WPA2, WPA2-PSK
and WPA-Mixed.
10. Click on the Apply button to save
the changes
WARNING:
If device failed to obtain valid IP from
a DHCP server, the device will be
inaccessible. To access the device
you will have press reset button for 5
seconds to restore IP settings back to