Entryvue 13535 User manual

The design and specifications can be changed without notice to users.
Copyright of this manual is reserved.
VIDEO DOOR PHONE SYSTEM
USER MANUAL (English)
Item No. : 13535, 13536
Version2.0.1.1.12.01

Camera Lens
Speaker
-1-
CONTENTS 1. Parts and Funcons
Touch Sensive
Digital Keypad
Nameplate
Call Buon
Microphone
Rainy GuardSide View90mm
176mm
23mm
Rainy Guard
Side View
Camera Lens
Touch Sensive
Digital Keypad
Speaker
Nameplate
Call Buon
Microphone
119mm
220mm
Screws for panel
mounng
1.1 Door Staon E
1.2 Door Staon F
1. Parts and Funcons - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1
2. Mounng and Seng - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
2.1 Door staon Mounng - - - - - - - - - - - - - - - - - - - - - - - - 2
3. Terminal Descripons - - - - - - - - - - - - - - - - - - - - - - - - - - - 5
4. System Wiring and Connecons - - - - - - - - - - - - - - - - - - - - 6
4.1 Basic Connecon - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
4.2 Electric Lock Connecon - - - - - - - - - - - - - - - - - - - - - - - 6
4.3 Electromagnec Lock Connecon - - - - - - - - - - - - - - - - - 7
4.4 Mul Door Staons Connecon - - - - - - - - - - - - - - - - - - - 9
4.5 Mul Monitors Connecon - - - - - - - - - - - - - - - - - - - - - - 10
5. DIP Switches Seng - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -11
5.1 DIP Switches Sengs of Doorstaon - - - - - - - - - - - - - - -11
5.2 DIP Switches Sengs of Monitor - - - - - - - - - - - - - - - - - -11
6. ID Card Registraon - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -12
6.1 Introducon - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 13
6.2 Add User Cards - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12
7. Unlock Operaons - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 14
7.1 Unlocking user code - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 14
8. Precausons - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 15
9. Specificaons - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 15

-3--2-
2. Mounng and Seng
2.1 Door Staon Mounng
Door Staon E Mounng Door Staon F Mounng
Adjust camera angle
1 2
43
Drill holes in the wall to match the size of
screws and aach the rainy guard to the wall.
Aach the panel to the rainy guard. Use the screwdriver and the screw to fix
the panel.
Connect the cable correctly and adjust
camera to the right angle.
Adjust
camera angle
1 2
43
Drill holes in the wall to match the size of
the mounng box and aach it to the wall.
Aach the panel to the mounng box and
use supplied screws to fix the panel.
Place name label.
Connect the cable correctly and adjust
camera to the right angle.

-4- -5-
3. Terminal Descripons
MIC adjustment
SPK adjustment
1 2 3 4
ON DIP
Lock Control Jumper
Doorstaon Code DIP
321
BUS
PL
S1+ S2+ S-
Main Connect Port
• Lock Control Jumper: To select the lock type: see secon 5
• Doorstaon Code DIP: It supports total 4 door staons,see secon 6
• MIC: Adjust the volume of Microphone
• SPK: Adjust the volume of Speaker
• Main Connect Port: To connect the bus line and the electronic locks.
• BUS: Connect to the bus line, no polarity.
• PL: External lock power input, connect to the power posive(power +).
• S1+, S2+: Lock power(+) output, to connect 2 locks.
• S-: Lock power(-) output, connect to the power(-) input of locks(only when using the camera to power the
locks, if using the external power supply for the locks, the S- should not be connected).
2.3 Adjusng Camera Angle
2.2 Placing Name Label
Move the plasc cover away to
open the transparent name label
cover, insert name paper, then
put the plasc cover back to the
panel.
Use a screwdriver to loosen the
screw and adjust the angle for
the camera, then fix the screw.

Connect two lock
Jumper posion in 2-3
4. System Wiring and Connecons
4.1 Basic Connecon
4.2 Electric Lock Connecon
-
+
AC~
Monitor
DPS PS4
L1 L2 PL S1+ S2+ S-
EB
*
LOCK
BUS PL S1+ S2+ S-
LOCK
2nd
1ST
2nd
EB
*1ST
1 2 3
EB
*
LOCK
BUS PL S1+ S2+ S-
Connect one lock
Jumper posion in 2-3
1 2 3
Note:
1. Only applicable to the power on to unlock type of electronic locks.
2. The door lock is limited to 12V, and holding current must be less than 250mA.
3. The door lock control is not med from Exit Buon(EB).
4. The Unlock Mode Parameter of Monitor must be set to 0 (by default).
4.2.1 Door Lock Controlled by Internal Power
4.3 Electromagnec Lock Connecon
Note:
1. Only applicable to the power off to unlock type of electronic locks.
2. The door lock is limited to 12V, and holding current must be less than 250mA.
3. The door lock control is not med from Exit Buon(EB).
4. The Unlock Mode Parameter of Monitor must be set to 0 (by default).
4.3.1 Door Lock Controlled by Internal Power
Connect one lock
Jumper posion in 2-3
1 2 3
EB
*
LOCK
BUS PL S1+ S2+ S-
Normally closed
Connect two lock
Jumper posion in 2-3
EB
*
LOCK
LOCK
2nd
1ST
2nd
EB
*
1ST
1 2 3
BUS PL S1+ S2+ S-
Note:
1. The external power supply must be used according to the lock.
2. The inside relay contact is restricted to AC or DC 24V/3A.
3. The jumper must be taken off before connecng.
4. Setup the Unlock Mode of Monitor for different lock types.
• Power-on-to-unlock type:Unlock Mode=0 (by default)
• Power-off-to-unlock type:Unlock Mode=1
4.3.2 Door Lock Controlled by Dry Contact
Connect two lock
Take off the Jumper
1 2 3
BUS PL S1+ S2+ S-
LOCK
LOCK
POWER
SUPPLY
LOCK
BUS PL S1+ S2+ S-
POWER
SUPPLY
Connect one lock
Take off the Jumper
1 2 3
-7--6-

monitor
intercom
setup
exit
Outdoor Tone -- 01
Intercom Tone -- 05
Monitor Time -- 1min
Advanced Set...
Auto Record -- OFF
Exit
0
* * *
Password:
Slave Addr Set -- 0
Guard Unit Set -- 0
Date/Time Set...
Other Settings...
Information...
Exit
Hardware ver 0302
Software ver 0168
Voltage 22.4V
Manufacture 00.0T
Restore to default
Exit
Unlock Time 1
Unlock Mode 0
Exit
1. Press
setup
setup item
on main menu page.
2. Select Advanced Set...
password is required.
4. Select Informaon.. 5. Press UNLOCK buon
and hold for 2s.
6. Seng unlock mode to
0 or 1.
3. The default password is
2008.
-9--8-
4.3.3 Unlock parameter seng(set in monitor)
4.4 Mul Door Staons Connecon
Note:
1. Must connect DT596 correctly before seng.
2. The parameter will be saved in DT596 automacally,so you only need to set one monitor.
3. The above cutline is fit for T107 series monitors only,for T753,T863 series monitors,please refer to the
corresponding user manuals.
1# Camera
85~260VAC
DPS PS5
Monitors
L1 L2 PL S1+ S2+ S- L1 L2 PL S1+ S2+ S-L1 L2 PL S1+ S2+ S-L1 L2 PL S1+ S2+ S-
123 4
ON
123 4
ON
123 4
ON
123 4
ON
ID=00
ID=10
ID=01ID=11
2# Camera3# Camera4# Camera

5. DIP Switches Seng
-11--10-
4.5 Mul Monitors Connecon 5.1 DIP Switches Sengs of Door Staon
5.2 DIP Switches Sengs of Monitor
Basic IN-OUT Wiring Mode ON(1)
=
OFF(0)
=
ON
ON
123 4
ON
123 4
ON
123 4
ON
123 4
ON
123 4
ON
123 4
ON
Total 4 bits on the DIP switches can be configured.The switches can be modified either before or aer installaon.
Seng Item Bit State Descripons
Bit1 and Bit2
(it is used to set
the ID code for
door staon)
Default seng, ID = 0(00), set to the first Door Staon.
ID = 1(10), set to the second Door Staon.
ID = 2(01), set to the third Door Staon.
ID = 3(11), set to the fourth Door Staon.
Bit3
Bit4
Acvate external output seng,the relay 2 terminal doesn't
respond to the second lock and will be closed for 60 seconds
when the "Lockout" is carried out.The alarm connected to
the terminal of relay 2 will be acvated.
inacvate
Reserve
There are 6 bit switches in total. The DIP switches are used to configure the User Code for each Monitor.
Bit-6 is line terminal switch, which needs to be set to ON if the Monitor is in the end of the bus, otherwise set to OFF.
Bit state Seng Bit state Seng
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
The monitor is
not at the end
of the bus.
The monitor is
at the end of
the bus.
Code=0, DIP-6=off
Code=14, DIP-6=off
Code=15, DIP-6=on
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
monitor
monitor
monitor
123 4
ON
ID=00
85~260AC
DPS PS5
Aenon: You must follow the dip switch sengs in the table on page 12.
So, 1st monitor all switches down, 2nd monitor switch 1 up, 3rd monitor
switch 2 up, etc.

Bit-1 to Bit-5 are used for User Code seng.The DT596 responds to 0~15 .
6.2.1 Control one lock (the first lock)
-13--12-
6. ID Card Registraon
BIT STATE USER CODE BIT STATE USER CODE BIT STATE USER CODE
Code=0 Code=6 Code=11
Code=1 Code=7 Code=12
Code=2 Code=8 Code=13
Code=3 Code=9 Code=14
Code=4 Code=10 Code=15
Code=5
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1 2 3 4 5 6
ON
1. Up to 1000 user cards can be registered to the door staon.
2. Easy management with LED status and sound hints.
3. There are two master cards, one MASTER CARD ADD card and one
MASTER CARD DELETE card, When registerening new master cards,
the old master cards will be invalid automacally.
4. Card reading distance is from 3 to 5 cm.
5. The master cards are necessary when you add or delete user cards.
Please keep it well for future use.
6.1 Introducon:
6.2 Add User Cards:
Show the MASTER CARD
ADD card to ID card window
in standby mode.
beep+,beep
red
(on) (off)
blue
Show the MASTER CARD
ADD card to exit.But it will
return to standby mode if no
operaon within 15s.
beep,beep+
red
(off) (off)
blue
Show user cards to be
added, one by one.
beep+
red
(blink) (off)
blue
6.2.2 Control two lock
Show the MASTER CARD
ADD card to ID card window
in standby mode.
beep+,beep
red
(on) (off)
blue
Show the MASTER CARD
ADD card to exit.But it will
return to standby mode if no
operaon within 15s.
beep,beep+
red
(off) (off)
blue
Press "CALL" buon.
At the same me, show
user cards to be added,
one by one.
beep+
red
(blink) (off)
blue
6.2.3 Delete User Cards:
Show the MASTER CARD
DELETE card to ID card
window in standby mode.
beep+,beep
red
(off) (on)
blue
Show the MASTER CARD
DELETE card to exit.But it
will return to standby mode
if no operaon within 15s.
beep,beep+
red
(off) (off)
blue
Show user cards to be
deleted in sequence.
beep+
red
(off) (blink)
blue
6.2.4 Access Inializaon (delete all user cards):
Show the MASTER CARD
DELETE card to ID card
window in standby mode.
beep+,beep+
red
(off) (on)
blue
Show the MASTER CARD
ADD card to ID card window
again, format operaon is
performing.
beep, beep,
beep, beep,
beep+
red
(off) (off)
blue
Show the MASTER CARD
ADD card to ID card window.
beep+
red
(on) (on)
blue

• Please clean the unit with so coon cloth, don't use the organic impregnant or chemical clean agent.
If necessary, please use a lile pure water or dilute soap water to clean the dust.
• The unit is weather resistant. However do not spray high pressure water on access control keypad directly.
Excessive moisture may cause problems with the unit.
• You must use the right adaptor which is supplied by the manufacture or approved by the manufacture.
• Pay aenon to the high voltage inside the products, please refer service only to a trained and qualified
professional.
8. Precausons
• Power Supply : DC 24V (supplied by PS4-24V or PS5-24V)
• Power Consumon : Standby 60mA; Working status 200mA
• Camera : Pinhole Sharp Color CCD; 420 TV Lines
• Lock Power Supply : 12Vdc, 300mA(Internal Power)
• Number of relay circuits : 2
• Mounng : Surface mounng(DT596/ID), Flush mounng (DT596F/ID)
• Working temperature : -10ºC ~ +45ºC
• Wiring : 2 wires,non-polarityC
• Dimension: 176(H)×90(W)×28(D)mm(DT596/ID), 220(H)×119(W)×52(D)mm(DT596F/ID)
9. Specificaons
-15--14-
• If an authorized user card is being shown the buzzer will sound of beep+,
and the LED indicator will light up.
• If the unauthorized user card is being shown, the buzzer will sound of beep 3 mes.
Show the MASTER CARD
ADD card to ID card window
in standby mode.
beep+,beep
red
(on) (off)
blue
Show the MASTER CARD
ADD card to exit.But it will
return to standby mode if no
operaon within 15s.
beep,beep+
red
(off) (off)
blue
Show user cards to be
added, one by one.
beep+
red
(blink) (off)
blue
6.2.5 Authorize master cards:
By default,there are two master cards marked MASTER CARD ADD and MASTER CARD DELETE, but you
should know that the master card can be authorized by users at any me. That means any two user cards
can be authorized to master cards, when registered new master cards, the old master cards will be invalid
automacally.
7. Unlock Operaons
When the registered user card has been shown to ID card window, the LED indicator (the first lock : red ;
the second lock : blue) lights up, the buzzer sounds, and the electric door strike will be unlocked.
Note 1 : if the user card controls one lock only,show the user card to release the first lock.red indicator lights up.
Note 2 : if the user card controls two locks,show the user card to ID card window in standby mode,the red & blue
indicator flashes for 1.5s alternately.During this me,press "CALL" buon to release the second lock.
Otherwise, release the first lock if there isn't any operaon within 1.5 seconds.
• If 10 mes unauthorized access cards are connuously aempted, the release funcon will be forbidden
and the showing card operaon will be disabled for 60 seconds.
• If the DIP3 switch is set to 1 and the relay 2 doesn't respond the second lock, in which when showing
user cards controlling two locks or when pressing unlock 2nd on monitor, the monitor, the second lock
whouldn’t release. At this point, aer to 10th aempts of showing access card, relay 2 will be closed for
60 seconds and the buzzer will connuously sound about 8 mes, if the system is connected to thr alarm,
the alarm funcon will be acvated.
7.1 Unlocking ID Card
Example: Release the first lock
Red LED lights up
(During relay 1 operaon)
beep+
red
(on) (off)
blue
Example: Release the second lock
Red LED lights up
(During relay 2 operaon)
beep+
red
(off) (on)
blue
• You can acvate the electric door strike by pressing the request to exit buon connected to the unit.
Pressing request to exit buon 1 releases relay 1, and pressing request to exit buon 2 releases relay
2.(The unlock funcon will work when the request to exit buon is being pushed, even while the
proximity access is forbidden.