E+E Elektronik EE870 User manual

Manual
EE870
Modular CO2Transmitter
BA_EE870_e // v1.1 // Technische Änderungen vorbehalten // 193937

2
For technical data, options and accessories please see EE870 data sheet at www.epluse.com/EE870
The modular CO2transmitter EE870 consists of following components:
• EE871 interchangeable CO2probe with E2 digital output. For technical data please see EE871 data sheet
(www.epluse.com/EE871)
For readjustment of EE871 please see data sheet and operation manual EE-PCS Product Configuration Software
(www.epluse.com/EE-PCS)
• HA011014 converter board. The converter board supplies the EE871 CO2probe and converts its
digital output signal into analog outputs and Modbus RTU digital interface. The measured data is available
simultaneously on the analogue outputs and on the Modbus interface. Technical data, setup and operations
instructions for HA011014 are detailed in this document.
• Connecting cable between EE871 CO2probe and HA011014. EE870 scope of supply includes one of the following
cables, as ordered:
• HA010810 ...........2m length
• HA010811 ...........5m length
• HA010812 .........10m length
GENERAL
General
Supply voltage 10-35VDC
10-28.8VAC
Supply current 300mA at 10VDC
120mA at 24VDC
Dimmensions of circuit board 78 x 48 x 25.8mm (0.26 x 0.16 x 1.02ft)
Pobe cable lenght max. 10m (32.8ft)
Temperature working range -40...60°C (-40...140°F)
Protection class IP00
Analog Output
Voltage-/ 0-1V; 0-5V; 0-10V -1mA < IL< 1mA
Current outputs 0-20mA; 4-20mA RL< 500Ohm
Conversion rate Output value is updated every 200ms
Resolution 12bit
D/A Conversion accuracy Voltage output: +/- 10mV
  Currentoutput: +/-30μA
Temperature dependence Voltage: typ. ±200ppm / °C
  Current: typ.±1μA/°C
Long-term stability Drift < 0,2% / year
Modbus
Register see Modbus Map
Modbus connections Connecting the supply voltage to the modubs terminals may destroy thedevice.
HA011014 converter board is supplied as a component and must be installed in accordance with the valid ESD
guidelines and properly protected against enviromental influences.
TECHNICAL DATA
IMPORTANT NOTES
66 (2.6“)
3.2 (1.13“)
6
(0.24“)
6
(0.24“)
39 (1.54“)
4.5
(0,18“)
4.5
(0,18“)
25.8 (1.02“)
13.8 (0.55“)
78 (3.08“)
+5V white
SCL black
SDA blue
GND brown
Shield grey
analog outputs
Jumper "Fast/Slow"
Jumper "Output Range"
Terminals for cable EE871
Modbus terminals
Modbus-Dipswitch
supply terminal
LED:
on = OK
fast flash = Error
Conversion Board
Digital CO2Probe EE871
96 (3.78“)
18.5 (0.73“)
M12x1 Gewicht: 30g
Weight: 30g (1.06oz)
CONNECTIONS / MOUNTING

3
Jumper for setting the analogue output:
Current Voltage
- 0-1V
0-20mA 0-5V
4-20mA 0-10V
Jumper for setting the response time:
fast response time
slow response time
Example:
Jumper "Output Range" set to 0...10V.
Jumper "Fast/Slow" set to "Fast"
Analog-Output
Modbus-Interface
HARDWARE SETTINGS
Dipswitch for modbus settings
S1, S2 baud rate
S3 stopbit
S4 parity
S5 - S10 addresse of the converter
Jumper for terminator settings
active/inactive
Example:
Dip-switch S1 and S2 "Baud rate" set on 19200
Dip-switch S3 "Stopbit" set on "one"
Dip-switch S4 "Parity" set on "even"
Dip-switch S5 - S10 "Address" set on "13" (activate S5/S7/S8)
Jumper "Terminator" set on "No"
MODBUS MAP
Register
address Parameter name Protocol address
0x00
SN Hardware
0
0x01 1
0x02 2
0x03 3
0x04 4
0x05 5
0x06 6
0x07 7
0x08 FW Version 8
0x09
Partname of Transmitter
9
0x0A 10
0x0B 11
0x0C 12
0x0D 13
0x0E 14
0x0F 15
0x10 16
0x11
Serialnumber E2 Transmitter
17
0x12 18
0x13 19
0x14 20
0x15 21
0x16 22
0x17 23
0x18 24
Register
address Parameter name Protocol address
0x19 Measured value 1 25
0x1A 26
0x1B Measured value 2 27
0x1C 28
0x1D Measured value 3 29
0x1E 30
0x1F Measured value 4 31
0x20 32
0x21 Gain Spannung 33
0x22 34
0x23 Offset Spannung 35
0x24 36
0x25 Gain Strom 37
0x26 38
0x27 Offset Strom 39
0x28 40
0x29 Measrange low 41
0x2A 42
0x2B Measrange high 43
0x2C 44
0x2D Analog Output low (V) 45
0x2E 46
0x2F Analog Output high (V) 47
0x30 48
0x31 Slow or Fast 49
0x32 50
ASCII
ASCII
ASCII
FLOAT
HIGH BYTE - main version
LOW BYTE - sub version

E+E Elektronik Ges.m.b.H.
Langwiesen 7, A-4209 Engerwitzdorf
Austria
Tel: [phone]
Fax: [phone]
[email protected]
E+E Elektronik France
Tél: [phone]
[email protected] / www.epluse.fr
E+E Elektronik Germany
Tel: [phone]
[email protected] / www.epluse.de
E+E Elektronik Korea
Tel: [phone]
i[email protected] / www.epluse.co.kr
E+E Elektronik Italy
Tel: [phone]
[email protected] / www.epluse.it
E+E Elektronik China / Beijing
Tel: [phone]
[email protected] / www.epluse.cn
E+E Elektronik China / Shanghai
Tel: [phone]
[email protected] / www.epluse.cn
E+E Elektronik USA
Tel: [phone]
[email protected] / www.epluse.com
R
Ges.m.b.H.
YOUR PARTNER IN SENSOR TECHNOLOGY
www.epluse.com
E+E ELEKTRONIK HEADQUATERS
E+E ELEKTRONIK SUBSIDIARIES