E+E Elektronik EE210 User manual

The EE210 transmitter, available for wall or duct mounting, is designed for the highly accurate measurement of humidity and tempera-
ture in demanding climate control applications. The EE210 incorporates the E+E humidity and temperature sensor HCT01.
For use in special applications do not hesitate to contact E+E Elektronik or a local distributor.
GENERAL
• For accurate measurement it is essential that the temperature of the sensing probe and mainly of the sensing head is same as
the temperature of the air to measure. Avoid mounting the transmitter in a way which creates temperature gradients along the
probe.
• The transmitter and mainly the sensing head shall not be exposed to extreme mechanical stress.
• The transmitter must be operated with the filter cap on at all times.Do not touch the sensors inside the sensing head.
• While replacing the filter cap (because of pollution for instance) against an original spare one please take very good care to
not touch the sensors.
CAUTION
USER‘S GUIDE
EE210 - Humidity and Temperature Transmitter for
demanding Climate Control Applications
EE210-HT6*
20...30VDC RL<500 Ohm
11...30VDC RL<50 Ohm
Output: 4...20mA
Output: 0...5V
0...10V
Output:
Modbus RTU or
BACnet MS/TP
15...35VDC
24VAC ±20%
15...35VDC
24VAC ±20%
EE210-HT3
EE210-HTx3
CONNECTION DIAGRAM
ONLY FOR REMOTE PROBE!
ONLY FOR REMOTE PROBE!
*Important:
In the case of EE210-HT6 (4...20mA, two-wire version) the display
operates only if both outputs are connected.
Bus termination resistor 120 Ω (jumper)

Green LED - information to normal operation mode:
on = everything OK
fl ashing = the main board does not recognize the
measurement electronics inside the sensing probe
off = no power supply or main board failure
Blue LED - information during setup with the optional
E+E Con guration Kit:
on = E+E Product Con guration Adapter (EE-PCA) is
powered, no communication in progess
fl ashing = EE-PCA powered, communication in progress
off = EE-PCA not connected to the EE210
LED INDICATION
CONNECTION DIAGRAM
EE210P (type C)
The EE210P remote probe for EE210-HT6xPC (4 … 20mA, 2-wire) and HTx3xPC (RS485 interface) shall be ordered and it is supplied
as separate item. EE210P is to be connected to the EE210 by the user.
• Install first the cable gland onto the EE210 enclosure.
• Before connecting the probe, disconnect the EE210 power supply.
• Insert the EE210P cable through the cable gland and connect it to the screw terminals according to the connection diagram below.
Please note:
EE210P is an intelligent probe with digital output and as such it is interchangeable. In case the probe or its cable gets destroyed or if a
longer cable is needed, please order a replacement probe according to EE210 data sheet. The replacement probe shall be installed as
described above.
Important:
Make sure that the cable glands are closed tightly for both EE210P probe cable and for the power supply and outputs cable. This is
necessary for assuring the protection class (IP class) of the enclosure according to EE210 speci cation, as well as for stress relief at the
screw terminals on the EE210 board.
Factory Setup:
The display shows the two parameters selected for output 1 and output 2 (accor-
ding to ordering code). For digital output versions the display shows RH and T.
User Setup:
The user can change the display layout to 1, 2 or 3 lines and select the
parameters to be displayed by using EE-PCS Product Configuration Software
(free download from www.epluse.com/configurator) and the optional EE-PCA
Product Configuration Adapter (not included in the scope of supply).
Important:
In the case of EE210-HT6 (4...20mA, two-wire version) the display operates only
if both outputs are connected.
DISPLAY

DIGITAL SETTINGS
Protocol setting:
Address, baudrate, parity and stop bits can be set via:
1. Congurator software (available on www.epluse.com/EE210)
2. Modbus protocol (please see Application Note Modbus (available on www.epluse.com/EE210)
FLOAT (read register):
Register
address
Communication
address
Parameter
name
30026 0x19 temperature [°C], [°F]
30028 0x1B relative humidity [%]
30030 0x1D water vapour partial pressure [mbar], [psi]
30032 0x1F dew point temperature [°C], [°F]
30036 0x23 absolute humidity [g/m³], [g/ft³]
30038 0x25 mixing ratio [g/kg], [gr/lb]
30040 0x27 specic enthalpy [kJ/kg], [BTU/lb]
30042 0x29 frost point temperature [°C], [°F]
The measured values are saved as a 32Bit float value from 0x19 to 0x1F and from 0x23 to 0x29. Additionally the measured values
are available as 16Bit signed integer from 0x12C to 0x12F and from 0x131 to 0x134.
The factory setting for the Slave-ID (Modbus address) is 242 as an integer 16Bit value. This ID can be changed by the user in the
register 60001 (0x00), permitted values are 1 - 247 permitted.
The serial number as ASCII-code is located at register address 30001-30008 (16Bit per address).
The Firmware version is located at register address 30009 (Bit 15...8 = major release; Bit 7...0 = minor release).
The choice of measurement units (metric or not metric) must be done in the ordering guide, see EE210 data sheet.
Switching from metric to non metric or vice versa by using the EE-PCS is not possible.
BACnet PICS are abvailable for download at www.epluse.com/EE210
INTEGER (read register):*
Register
address
Communication
address
Parameter
name
30301 0x12C temperature [°C], [°F]
30302 0x12D relative humidity [%]
30303 0x12E water vapour partial pressure [mbar], [psi]
30304 0x12F dew point temperature [°C], [°F]
30306 0x131 absolute humidity [g/m³], [g/ft³]
30307 0x132 mixing ratio [g/kg], [gr/lb]
30308 0x133 specic enthalpy [kJ/kg], [BTU/lb]
30309 0x134 frost point temperature [°C], [°F]
* Values are stored with a scaling of 1:100 (e.g.: 2550 is equivalent to 25.5°C)
INTEGER (write register):*
Register
address
Communication
address
Parameter
name
60001 0x00 Slave-ID (modbus addresse)
60002 0x01 Modbus protocol settings*
*For Modbus protocol setting please see Application Note Modbus
(www.epluse.com/EE210)
INFO (read register):
Register
address
Communication
address
Parameter
name
30001 0x00 Serial number (as ASCII)
30009 0x08 Firmware version
BACnet Setup
Modbus Setup
Address Switch
Address Switch
Slave address setting via EE-PCS Product Conguration Software:
All switches at position 0 → address has to be set via conguration software
(factory setting 242).
Example: Slave address is set via conguration software.
Slave address setting via Dip-Switch:
Setting the Dip-Switch to any other address than 0 overwrites the slave address set
via conguration software.
Example: Slave address set to 11 (=00001011 binary).
0
1
0
1

TECHNICAL DATA
∆ °C
°C
∆ °C
°C
(Modification rights reserved)
Measured Values
Relative Humidity (RH)
Sensor E+E Sensor HCT01-00D
Working range 0...100% RH
RH accuracy (incl. hysteresis, non-linearity and repeatability)
Wall & duct version:
-15...40°C (5...104°F) ≤90% RH ±(1.3 + 0.003*measured value) % RH
-15...40°C (5...104°F) >90% RH ± 2.3% RH
-40...60°C (0...140°F) ±(1.5 + 0.015*measured value) % RH
Remote probe version
at 20°C (68°F) ±2.5% RH
Temperature (T)
Sensor Pt1000 (tolerance class B, DIN EN 60751) integrated in HCT01
T-accuracy wall & duct remote probe
Outputs
Analog output 0-5 V / 0-10 V -1 mA < IL< 1 mA
(RH: 0...100%; T: see ordering guide) 4-20 mA (two-wire) RL≤ 500 Ohm
Digital output RS485 (BACnet MS/TP or Modbus RTU), max. 32 EE210 in one bus
General
Power supply
for 0-5 V / 0-10 V / RS485 15 - 35V DC1) or 24V AC ±20%
for 4-20 mA 10V + RL x 20 mA < V+ < 30V DC
Current consumption
Voltage output DC supply typ. 3.3mA; with display typ. 3.6mA
AC supply typ. 34mA; with display typ. 37mA
Current output DC supply max. 40mA
Digital interface DC supply typ. 5mA; with display typ. 19mA
AC supply typ. 52mA; with display typ. 118mA
Display 1, 2 or 3 lines, user configurable
Connection Screw terminals, max. 1.5 mm2
Housing material Polycarbonate, UL94V-0 (with Display UL94HB) approved
Protection class IP65 / NEMA 4
Cable gland M16 x 1.5
Probe cable (type C) PVC, Ø 4.3mm, 4 x 0.25 mm2, Length: 1.5 or 3m (4.9 or 9.8ft)
Sensor protection E+E Coating
Electromagnetic compatibility EN61326-1 EN61326-2-3
Industrial Environment
Temperature ranges Operating: -40...60°C (-40...140°F) (-40...80°C for remote probe EE210P)
Storage: -40...60°C
(-40...140°F)
Temperature ranges with display Operating: -20...50°C (-4...122°F) (-40...80°C for remote probe EE210P)
Storage: -20...60°C
(-4...140°F)
1 USA & Canada: class 2 supply required, max. supply voltage 30V

FOR CONDUIT
INSTALLATION
CABLE GLAND M16x1.5
~55mm
~2.16“
Ø 12mm
Ø 0.47“
60 ±0.3mm
2.36 ±0.11“
Ø > 16mm
Ø > 0.63“
6mm
0.24“
90 ±0.3mm
3.54 ±0.11“
Ø > 13mm
Ø > 0.51“
~205mm
~8.07“
101mm
3.98“
19mm
0.75“
90 ±0.3mm
3.54 ±0.11“
46mm
1.81“
5mm
0.2“
80.6mm
3.17“
34mm
1.34“
106mm
4.17“
GASKET
Recommended mounting screws:
ST4.2x50 DIN7981C
Type C
Type A Type B
EE210P
DIMENSIONS / MOUNTING
SCOPE OF SUPPLY
EE210 WALL MOUNT (TYP A):
• EE210 Transmitter according Ordering Guide
• 1 x Cable gland
• Mounting kit
• Inspection certificate according to DIN EN10204 - 3.1
EE210 DUCT MOUNT (TYP B):
• EE210 Transmitter according Ordering Guide
• 1 x Cable gland
• Mounting flange
• Mounting kit
• Inspection certificate according to DIN EN10204 - 3.1
EE210 WITH REMOTE PROBE (TYP C):
• EE210 Transmitter according Ordering Guide
• 2 x Cable gland
• Mounting kit
• Inspection certificate according to DIN EN10204 - 3.1
EE210-P REMOTE PROBE:
• EE210-P according Ordering Guide
• Mounting flange
• Inspection certificate according to DIN EN10204 - 3.1
• !! EE210-P is not included in the Scope of Supply of the EE210 Type C !!
ADDITIONALLY FOR ALL EE210 WITH RS485 INTERFACE:
• 1 x Cable gland
• Quick Guide – EE210 Modbus Setup

INFORMATIONEN [phone] / [email protected]
Langwiesen 7 • A-4209 Engerwitzdorf
Tel: [phone] • Fax: [phone]
[email protected] • www.epluse.com
LG Linz Fn 165761 t • UID-Nr. ATU44043101
Place of Jurisdiction: A-4020 Linz • DVR0962759
ACCESSORIES
Position 1:
- configuration adapter (incl. USB cable for PC) EE-PCA
Position 2:
- cable for configuration adapter HA011062
Position 3:
- configuration software: EE-PCS
free of charge; download: www.epluse.com/EE210
Position 4 - optional:
- power supply for EE210 V03
Configuration kit: The con guration kit allows user setup for the output scaling and for the interface parameters, as well as humidity
and temperature adjustment of the sensor.
BA_EE210_e // v1.3 // Modification rights reserved
USA
FCC notice:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the installation manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CANADIAN
ICES-003 Issue 5:
CAN ICES-3 B / NMB-3 B
MAINTENANCE
When employed in dusty, polluted environment:
• The filter cap shall be replaced once in a while with an E+E original one. A polluted filter cap causes longer response time of the
device.
• If needed, the sensing head can be cleaned. For this remove first very carefully the filter cap. Take care not to hit the sensing
head. Shake slowly the sensing head for one minute in a solution of 50% isopropyl alcohol with 50% distilled water. Then the sen-
sing head shall be rinsed with cold tap water and let dry freely. Do not touch or rub the sensing head! After cleaning the sensors
install carefully a new E+E original filter cap.
The EE210 transmitter is ready to use and does not require any con guration by the user. The factory setup of EE210 corresponds to the
type number ordered. (Ordering guide please see data sheet at www.epluse.com/EE210.)
If needed, the user can change the factory setup by using the optional E+E Product Configuration Adapter (EE-PCA) and the E+E
Product Configuration Software (EE-PCS).
One can assign other physical quantities to the analogue outputs, change the scaling of the outputs and perform one or two point ad-
justment for humidity and temperature.
For con guration with EE-PCA and EE-PCS both 4-20 mA two-wire outputs must be connected.
For product data sheets EE-PCS and EE-PCA please see www.epluse.com.
The E+E Product Configuration Software (EE-PCS) is free and can be downloaded from www.epluse.com/configurator.
SETUP AND ADJUSTMENT

PC
HA011062
HA011050
V03 (optional)