Epson S5U13A05P00C100 User manual

Rev. 1.02
S1D13A05 LCD/USB Companion Chip
S5U13A05P00C100 Evaluation
Board User Manual
Document Number: X40A-G-014-01.02

NOTICE
No part of this material may be reproduced or duplicated in any form or by any means without the written permission
of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does
not assume any liability of any kind arising out of any inaccuracies contained in this material or due to its application
or use in any product or circuit and, further, there is no representation that this material is applicable to products
requiring high level reliability, such as, medical products. Moreover, no license to any intellectual property rights
is granted by implication or otherwise, and there is no representation or warranty that anything made in accordance
with this material will be free from any patent or copyright infringement of a third party. When exporting the
products or technology described in this material, you should comply with the applicable export control laws and
regulations and follow the procedures required by such laws and regulations. You are requested not to use, to resell,
to export and/or to otherwise dispose of the products (and any technical information furnished, if any) for the devel-
opment and/or manufacture of weapon of mass destruction or for other military purposes.
All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective
companies.
©SEIKO EPSON CORPORATION 2007-2018. All rights reserved.
Evaluation Board/Kit and Development Tool Important Notice
1. This evaluation board/kit or development tool is designed for use for engineering evaluation, demonstration, or develop-
ment purposes only. Do not use it for other purposes. It is not intended to meet the requirements of design for finished
products.
2. This evaluation board/kit or development tool is intended for use by an electronics engineer and is not a consumer product.
The user should use it properly and in a safe manner. Seiko Epson does not assume any responsibility or liability of any
kind of damage and/or fire caused by the use of it. The user should cease to use it when any abnormal issue occurs even
during proper and safe use.
3. The part used for this evaluation board/kit or development tool may be changed without any notice.
2Seiko Epson Corporation S5U13A05P00C100 Evaluation Board
Rev. 1.02

S5U13A05P00C100 Evaluation Board Seiko Epson Corporation 3
Rev. 1.02
Table of Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3 Installation and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 Configuration DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2 Configuration Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 CPU Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1 CPU Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2 CPU Bus Connector Pin Mapping . . . . . . . . . . . . . . . . . . . . . . 12
5 LCD Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6 Technical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.1 PCI Bus Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.2 Direct Host Bus Interface Support . . . . . . . . . . . . . . . . . . . . . . 16
6.3 S1D13A05 Embedded Memory . . . . . . . . . . . . . . . . . . . . . . . 16
6.4 Software Adjustable LCD Backlight Intensity Support Using PWM . . . . . . . . . 16
6.5 LCD Panel Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.5.1 LCD Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.5.2 Extended LCD Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.5.3 TFT Type 3 Extended LCD Connector . . . . . . . . . . . . . . . . . . . . . . . . 18
6.6 USB Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.6.1 USB IRQ Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.7 External oscillator support for CLKI and CLKI2 . . . . . . . . . . . . . . . . . 18
6.8 External oscillator support for USBCLK . . . . . . . . . . . . . . . . . . . . 18
7 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
8 Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
9 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
10 Change Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
11 Sales and Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

4Seiko Epson Corporation S5U13A05P00C100 Evaluation Board
Rev. 1.02

Introduction
S5U13A05P00C100 Evaluation Board Seiko Epson Corporation 5
Rev. 1.02
1 Introduction
This manual describes the setup and operation of the S5U13A05P00C100 Evaluation
Board. The board is designed as an evaluation platform for the S1D13A05 LCD/USB
Companion Chip.
This document is updated as appropriate. Please check for the latest revision of this
document before beginning any development. The latest revision can be downloaded at
vdc.epson.com.
We appreciate your comments on our documentation. Please contact us via email at
vdc-document[email protected].com.

Features
6Seiko Epson Corporation S5U13A05P00C100 Evaluation Board
Rev. 1.02
2 Features
Following are some features of the S5U13A05P00C100 Evaluation Board:
• 121-pin PFBGA S1D13A05 Embedded Memory LCD Controller with 256K bytes of
embedded SRAM.
• PCI bus operation through onboard PCI bridge.
• CPU/Bus interface header strips for non-PCI bus operation.
• Configuration options.
• Software adjustable backlight intensity support using PWMOUT.
• 4/8-bit 3.3V or 5V single monochrome passive LCD panel support.
• 4/8/16-bit 3.3V or 5V single color passive LCD panel support.
• 9/12/18-bit 3.3V or 5V active matrix TFT LCD panel support.
• Direct interface for 18-bit Sharp HR-TFT LCD panel support.
• Direct interface for 18-bit Casio TFT LCD panel support.
• Direct interface for 18-bit TFT Type 2 LCD panel support
• Direct interface for 18-bit TFT Type 3 LCD panel support
• Direct interface for 18-bit TFT Type 4 (Epson ND-TFD) LCD panel support.
• Connector for USB client support.
• Oscillators for CLKI and CLKI2.

Installation and Configuration
S5U13A05P00C100 Evaluation Board Seiko Epson Corporation 7
Rev. 1.02
3 Installation and Configuration
The S5U13A05P00C100 is designed to support as many platforms as possible. The
S5U13A05P00C100 incorporates a DIP switch and three jumpers which allow both the
evaluation board and the S1D13A05 LCD controller to be configured for a specified evalu-
ation platform.
3.1 Configuration DIP Switches
The S1D13A05 has seven configuration inputs (CNF[6:0]) which are read on the rising
edge of RESET#. In order to configure the S1D13A05 for multiple Host Bus Interfaces an
eight-position DIP switch (SW1) is required. The following figure shows the location of
DIP switch SW1 on the S5U13A05P00C100.
Figure 3-1: Configuration DIP Switch (SW1) Location
DIP Switch - SW1

Installation and Configuration
8Seiko Epson Corporation S5U13A05P00C100 Evaluation Board
Rev. 1.02
All S1D13A05 configuration inputs are fully configurable using the eight position DIP
switch as described below.
Table 3-1: Configuration DIP Switch Settings
Switch
(SW1)
S1D13A05
Signal
Value on this pin at rising edge of RESET# is used to configure:
Closed (On/1) Open (Off/0)
SW1-5,
SW1-[3:1]
CNF4,
CNF[2:0]
Select host bus interface as follows:
CNF4 CNF2 CNF1 CNF0 Host Bus Interface
1 0 0 0 SH-4/SH-3 interface, Big Endian
0 0 0 0 SH-4/SH-3 interface, Little Endian
1 0 0 1 MC68K #1, Big Endian
0 001 Reserved
1 0 1 0 MC68K #2, Big Endian
0 010 Reserved
1 0 1 1 Generic #1, Big Endian
0 0 1 1 Generic #1, Little Endian
1 100 Reserved
0 1 0 0 Generic #2, Little Endian
1 1 0 1 RedCap 2, Big Endian
0 101 Reserved
1 1 1 0 DragonBall, Big Endian
0 110 Reserved
X 111 Reserved
SW1-4 CNF3 Reserved. Must be set to 1.
SW1-6 CNF5 WAIT# is active high WAIT# is active low
SW1-7 CNF6 CLKI to BCLK Divide ratio 2:1 CLKI to BCLK divide ratio 1:1
SW1-8 - Disable PCI bridge for non-PCI host Enable PCI bridge for PCI host
= Required settings when using the PCI Bridge FPGA

Installation and Configuration
S5U13A05P00C100 Evaluation Board Seiko Epson Corporation 9
Rev. 1.02
3.2 Configuration Jumpers
The S5U13A05P00C100 has three jumper blocks which configure various settings on the
board. The jumper positions for each function are shown below.
JP3 - LCD Panel Voltage
JP3 selects the voltage level to the LCD panel.
When the jumper is at position 1-2, the voltage level is +3.3V (default setting).
When the jumper is at position 2-3, the voltage level is +5.0V.
Note
When configured for Sharp HR-TFT, JP3 and JP5 must be set to position 1-2.
Figure 3-2: Configuration Jumper (JP3) Location
Table 3-2: Jumper Summary
Jumper Function Position 1-2 Position 2-3 No Jumper
JP3 LCD Panel Voltage +3.3V LCDVCC +5V LCDVCC —
JP4 PCI_IRQ Disable Enable USB IRQ on PCI — Disable USB IRQ on PCI
JP5 GP00 Polarity on H3 Normal (Active High) Inverted (Active Low) GPO0 not sent to H3
= recommended settings
+5 LCDVCC
+3.3 LCDVCC
JP3

Installation and Configuration
10 Seiko Epson Corporation S5U13A05P00C100 Evaluation Board
Rev. 1.02
JP4 - PCI_IRQ Enable
JP4 selects whether the USB IRQ on PCI is enabled or disabled.
When the jumper is at position 1-2, the USB IRQ on PCI is enabled (default setting).
When no jumper is installed, the USB IRQ on PCI is disabled.
Figure 3-3: Configuration Jumper (JP4) Location
JP5 - GPO0 Polarity on H3
JP5 selects the polarity of the GPO0 signal available on the TFT Type 3 Extended LCD
Connector H3.
When the jumper is at position 1-2, the GPO0 signal is sent directly (active high) to H3
(default setting).
When the jumper is at position 2-3, the GPO0 signal is inverted and then sent (active low)
to H3.
When no jumper is installed, GPO0 is not sent to H3.
Figure 3-4: Configuration Jumper (JP5) Location
USB IRQ USB IRQ
JP4
on PCI enabled on PCI disabled
Normal Inverted GPIO0 not
JP5
(Active High) (Active Low) sent to H1