Epson S1D13C00 User manual

Rev. 1.0
S1D13C00
S5U13C00P01C100 Customer
Development Board User
Manual
Document Number: XB8A-G-001-01.0

Evaluation board/kit and Development tool important notice
1. This evaluation board/kit or development tool is designed for use for engineering evaluation, demonstration,
or development purposes only. Do not use it for other purposes. It is not intended to meet the requirements of
design for finished products.
2. This evaluation board/kit or development tool is intended for use by an electronics engineer and is not a
consumer product. The user should use it properly and in a safe manner. Seiko Epson dose not assume any
responsibility or liability of any kind of damage and/or fire coursed by the use of it. The user should cease to
use it when any abnormal issue occurs even during proper and safe use.
3. The part used for this evaluation board/kit or development tool may be changed without any notice.
NOTICE
No part of this material may be reproduced or duplicated in any form or by any means without the written
permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice.
Seiko Epson does not assume any liability of any kind arising out of any inaccuracies contained in this material
or due to its application or use in any product or circuit and, further, there is no representation that this material is
applicable to products requiring high level reliability, such as, medical products. Moreover, no license to any
intellectual property rights is granted by implication or otherwise, and there is no representation or warranty that
anything made in accordance with this material will be free from any patent or copyright infringement of a third
party. When exporting the products or technology described in this material, you should comply with the
applicable export control laws and regulations and follow the procedures required by such laws and regulations.
You are requested not to use, to resell, to export and/or to otherwise dispose of the products (and any technical
information furnished, if any) for the development and/or manufacture of weapon of mass destruction or for other
military purposes.
All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective
companies.
©SEIKO EPSON CORPORATION 2018-2019. All rights reserved.

S5U13C00P01C100 Board User Manual Seiko Epson Corporation i
(Rev. 1.0)
Table of Contents
1. Introduction ................................................................................................................ 3
2. Connecting the ET011TT2 EPD Panel ...................................................................... 5
3. Connecting to the Host MCU Board ......................................................................... 6
3.1 EK-TM4C1294XL Board .............................................................................................................6
3.2 Nucleo-F746ZG or Nucleo-F767ZI Board .................................................................................7
4. Jumpers Settings....................................................................................................... 8
5. Push-Buttons and EPD Panel Connectors .............................................................. 9
5.1 Push-Buttons ..............................................................................................................................9
5.2 Header for Hulk Power Board Connection (CN1) .................................................................10
5.3 FPC Connector for ET011TT2 Connection (CN2)..................................................................11
6. Pre-installed On-board Components ..................................................................... 12
6.1 16Mbytes QSPI Serial Flash (U2) ............................................................................................12
7. Host MCU Board Connections................................................................................ 13
7.1 Tiva C Series EK-TM4C1294XL Launchpad...........................................................................13
7.2 STM32 Nucleo-144 development board .................................................................................15
8. Parts List................................................................................................................... 17
9. S5U13C00P01C100 Schematics.............................................................................. 18
10. Revision History....................................................................................................... 20

ii Seiko Epson Corporation S5U13C00P01C100 Board User Manual
(Rev. 1.0)

Introduction
S5U13C00P01C100 Board User Manual Seiko Epson Corporation 3
(Rev. 1.0)
1. Introduction
The S5U13C00P01C100 is the S1D13C00 EPD Evaluation Board. It is a BoosterPack board with a connector
for the E Ink ET011TT2 EPD panel intended to be directly connected to the TI Tiva C Series EK-TM4C1294XL
Launchpad evaluation board for evaluating and developing embedded EPD applications using the Epson
S1D13C00 Memory Display Controller IC. It is possible to be controlled by the ST Nucleo-F746ZG or Nucleo-
F767ZI board through the S5U13C00M00C100 (STM32 Nucleo-144 development board) board.
Figure 1 shows the S5U13C00P01C100 EPD Evaluation Board.
Figure 1 – S5U13C00P01C100 EPD Evaluation Board
The S5U13C00P01C100 EPD Evaluation Board consists of:
A S1D13C00 Memory Display Controller (U1)
Four 2x10 connectors for Host Interface connection (J4, J5, J6 and J7) and +5V/+3.3V power
A 16Mbytes QSPI Serial Flash (U2)
A flexible printed circuit (FPC) connector (CN2) for connecting to a ET011TT2 EPD panel
An 18-pin right-angle header connector for connecting to other panels
Figure 1.1 shows the block diagram of S5U13C00P01C100, focused on interfaces. It has a host MCU interface
and three interfaces for displays. CN1 is an interface for E Ink’s HULK power board, CN2 is an interface for the
ET011TT2 panel module, and there are through holes for interface to a memory display panel. You can select
one of these interfaces to connect a panel module. CN2 interface is also possible to connect other E Ink panel
modules. The booster components on the S5U13C00P01C100 are similar circuits to HULK power board
suitable for the ET011TT2 panel module.

Introduction
4Seiko Epson Corporation S5U13C00P01C100 Board User Manual
(Rev. 1.0)
Figure 1.1 – S5U13C00P01C100 Block Diagram for Interface
Regulator
Host
interface
Memory display interface
HULK power board interface
ET011TT2
panel module
interface
S1D13C00
Serial
Flash
Through holes
Booster
Components *
CN1
C
N
2
*Booster components are part of booster circuits of ET011TT2 panel module.

Connecting the ET011TT2 EPD Panel
S5U13C00P01C100 Board User Manual Seiko Epson Corporation 5
(Rev. 1.0)
2. Connecting the ET011TT2 EPD Panel
Figure 2 – Connecting the ET011TT2 EPD Panel
Figure 2.1 – Connecting the HULK Power Board with ET011TT2 EPD Panel

Connecting to the Host MCU Board
6Seiko Epson Corporation S5U13C00P01C100 Board User Manual
(Rev. 1.0)
3. Connecting to the Host MCU Board
3.1 EK-TM4C1294XL Board
Position the S5U13C00P01C100 EPD Evaluation Board on TOP of the EK-TM4C1294XL Launchpad Board,
press the two boards together with J4 connecting to X8, J5 connecting to X9, J6 connecting to X6, and J7
connecting to X7 respectively.
Figure 3 – Connecting the S5U13C00P01C100 to the EK-TM4C1294XL
J4
J5
J6
J7
X8
X9
X6
X7

Connecting to the Host MCU Board
S5U13C00P01C100 Board User Manual Seiko Epson Corporation 7
(Rev. 1.0)
3.2 Nucleo-F746ZG or Nucleo-F767ZI Board
First, connect the S5U13C00M00C100 adapter board to the Nucleo board. Second, connect the
S5U13C00P01C100 board to the S5U13C00M00C100 adapter board.
Figure 3.1 – Connecting the S5U13C00P01C100 to the Nucleo-F746ZG or Nucleo-F767ZI

Jumpers Settings
8Seiko Epson Corporation S5U13C00P01C100 Board User Manual
(Rev. 1.0)
4. Jumpers Settings
The following tables show the jumpers settings for the S5U13C00P01C100 EPD Evaluation Board.
Figure 4 – S5U13C00P01C100 Jumpers Locations
Jumpers
Descriptions
Type
Default Position
JP2
External VC3 Connection
2-pin
Not installed
JP3
VDD_IC supply series jumper
2-pin
Installed
JP4
VDD_EPD supply series jumper
2-pin
Installed
JP6
DISPVDD source supply
1-2 = VDD_EPD
2-3 = VMDL
3-pin
1-2 (VDD_EPD)
JP7
HIFCNF (host interface configuration)
1-2 = SPI/QSPI
2-3 = INDIRECT 8-BIT (not used)
3-pin
1-2 (SPI/QSPI)
JP2
JP3
JP4
JP6
JP7

Push-Buttons and EPD Panel Connectors
S5U13C00P01C100 Board User Manual Seiko Epson Corporation 9
(Rev. 1.0)
5. Push-Buttons and EPD Panel Connectors
Figure 5 – S5U13C00P01C100 Push-Buttons and EPD Panel Connector Locations
5.1 Push-Buttons
Push-Button
Description
SW1
Reset button
SW2
User button connected to P01 port pin
CN1
SW1
SW2
CN2

Push-Buttons and EPD Panel Connectors
10 Seiko Epson Corporation S5U13C00P01C100 Board User Manual
(Rev. 1.0)
5.2 Header for Hulk Power Board Connection (CN1)
The table below shows the pin assignments of CN1.
CN1
Pin
Pin name
Description
1
VDD_EPD
Power supply for EPD panel.
2
EPD_BS
Tied to VDD_EPD through resistor R49.
EPD bus select. 3-wire serial interface is selected.
3
EPD_RST
Connected to port P03 of S1D13C00.
EPD reset output from S1D13C00.
4
EPD_BUSY
Connected to port P02 of S1D13C00.
EPD busy input status to S1D13C00.
5
HST/EPD_CSB
Chip-select for EPD panel.
Connected to HST output of S1D13C00.
6
VCK/EPD_DC
Data/command select for EPD panel.
Connected to VCK output of S1D13C00.
7
EPD_P51
Connected to P06 port of S1D13C00.
8
-
-
9
-
-
10
-
-
11
P07
Connected to P07 port of S1D13C00.
12
VST/EPD_SCL
Serial clock for EPD panel.
Connected to VST output of S1D13C00.
13
-
-
14
ENB/EPD_SDA
Serial data for EPD panel.
Connected to ENB output of S1D13C00.
15
-
-
16
GND
Ground.

Push-Buttons and EPD Panel Connectors
S5U13C00P01C100 Board User Manual Seiko Epson Corporation 11
(Rev. 1.0)
5.3 FPC Connector for ET011TT2 Connection (CN2)
The following table shows the pinout and signal connections of the 24-pin FPC (CN2):
CN2 Pin
Pin
Connection
Description
1
EPD_P51
Connected to P06 port of S1D13C00.
2
FETG
GDR signal of EPD panel.
3
FETS
RESE signal of EPD panel.
4
VGL
VGL supply from EPD panel.
5
VGH
VGH supply from EPD panel.
6
EPD_TSCL
I2C clock for external temperature sensor on EPD panel.
7
EPD_TSDA
I2C data for external temperature sensor on EPD panel.
8
EPD_BS
Tied to VDD_EPD through resistor R49.
EPD bus select. 3-wire serial interface is selected.
9
EPD_BUSY
Connected to port P02 of S1D13C00.
EPD busy input status to S1D13C00.
10
EPD_RST
Connected to port P03 of S1D13C00.
EPD reset output from S1D13C00.
11
VCK/EPD_DC
Data/command select for EPD panel.
Connected to VCK output of S1D13C00.
12
HST/EPD_CSB
Chip-select for EPD panel.
Connected to HST output of S1D13C00.
13
VST/EPD_SCL
Serial clock for EPD panel.
Connected to VST output of S1D13C00.
14
ENB/EPD_SDA
Serial data for EPD panel.
Connected to ENB output of S1D13C00.
15
VDD_EPD
VC1 supply to EPD panel. (No-connect on panel side.)
16
VDD_EPD
VC1 supply to EPD panel.
17
GND
Ground.
18
VDD
VDD supply from EPD panel.
19
P07
Connected to P07 port of S1D13C00.
20
VSH
VSH supply from EPD panel.
21
PREVGH
PREVGH supply to EPD panel.
22
VSL
VSL supply from EPD panel.
23
PREVGL
PREVGL feedback from EPD panel.
24
VCOM_EPD
VCOM supply from EPD panel.

Pre-installed On-board Components
12 Seiko Epson Corporation S5U13C00P01C100 Board User Manual
(Rev. 1.0)
6. Pre-installed On-board Components
Figure 6 – S5U13C00P01C100 pre-installed on-board components locations
6.1 16Mbytes QSPI Serial Flash (U2)
This serial flash is directly connected to the QSPI interface of the S1D13C00. The flash can be optionally
accessed (read-only) through the Memory-Mapped Access area on the memory map of the S1D13C00.
U2

Host MCU Board Connections
S5U13C00P01C100 Board User Manual Seiko Epson Corporation 13
(Rev. 1.0)
7. Host MCU Board Connections
7.1 Tiva C Series EK-TM4C1294XL Launchpad
The following tables show the signals of the Tiva C Series EK-TM4C1294XL Launchpad connectors which are
used by the S5U13C00P01C100 Customer Development Board:
J4
EK-TM4C1294XL
Connector X8 Signals
S5U13C00P01C100
Signal
1
3V3
-
2
5V
HOST_5V
3
PE4
HIFD0
4
GND
GND
5
PC4
HIFD7
6
PE0
-
7
PC5
HIFD6
8
PE1
-
9
PC6
HIFD5
10
PE2
-
11
PE5
HIFD1
12
PE3
-
13
PD3
-
14
PD7
-
15
PC7
HIFD4
16
PA6
-
17
PB2
-
18
PM4
P11
19
PB3
HIFRD
20
PM5
HIFIRQ
J5
EK-TM4C1294XL
Connector X9 Signals
S5U13C00P01C100
Signal
1
PF1
-
2
GND
GND
3
PF2
-
4
PM3
-
5
PF3
-
6
PH2
-
7
PG0
-
8
PH3
-
9
PL4
-
10
TARGET_RST#
nRST
11
PL5
-
12
PD1
-
13
PL0
-
14
PD0
-
15
PL1
-
16
PN2
-
17
PL2
-
18
PN3
-
19
PL3
-
20
PP2
-

Host MCU Board Connections
14 Seiko Epson Corporation S5U13C00P01C100 Board User Manual
(Rev. 1.0)
J6
EK-TM4C1294XL
Connector X6 Signals
S5U13C00P01C100
Signal
1
3V3
HOST_3.3V
2
5V
HOST_5V
3
PD2
-
4
GND
GND
5
PP0
-
6
PB4
HIFDE
7
PP1
-
8
PB5
HIFWR
9
PD4
HIFD2
10
PK0
-
11
PD5
HIFD3
12
PK1
-
13
PQ0
-
14
PK2
-
15
PP4
-
16
PK3
-
17
PN5
-
18
PA4
-
19
PN4
-
20
PA5
-
J7
EK-TM4C1294XL
Connector X7 Signals
S5U13C00P01C100
Signal
1
PG1
-
2
GND
GND
3
PK4
-
4
PM7
-
5
PK5
-
6
PP5
-
7
PM0
-
8
PA7
-
9
PM1
-
10
TARGET_RST#
-
11
PM2
-
12
PA3/PQ2
-
13
PH0
-
14
PA2/PQ3
-
15
PH1
-
16
PP3
HIFCS
17
PK6
-
18
PQ1
-
19
PK7
-
20
PM6
-

Host MCU Board Connections
S5U13C00P01C100 Board User Manual Seiko Epson Corporation 15
(Rev. 1.0)
7.2 STM32 Nucleo-144 development board
The following tables show the signal connections map between the S5U13C00P01C100 board and the STM32
Nucleo-144 development board:
S5U13C00P01C100 Board
STM32 Nucleo-144 development
board
Description
Signal
Signal
J4-1
-
-
-
J4-2
HOST_5V
+5V
CN8-9
5V supply
J4-3
HIFD0
PD11
CN10-23
Host SPI/QSPI D0
J4-4
GND
GND
CN7-8
Ground
J4-5
HIFD7
PE10
CN10-24
Host INDIRECT8 D7
J4-6
-
-
-
J4-7
HIFD6
PE9
CN10-4
Host INDIRECT8 D6
J4-8
-
-
-
J4-9
HIFD5
PE8
CN10-18
Host INDIRECT8 D5
J4-10
-
-
-
J4-11
HIFD1
PD12
CN10-21
Host SPI/QSPI D1
J4-12
-
-
-
J4-13
-
-
-
J4-14
-
-
-
J4-15
HIFD4
PE7
CN10-20
Host INDIRECT8 D4
J4-16
-
-
-
J4-17
-
-
-
J4-18
-
-
-
J4-19
HIFRD
PD4
CN9-8
Host INDIRECT8 read signal
J4-20
HIFIRQ
PB1
CN10-7
Interrupt request to host
S5U13C00P01C100 Board
STM32 Nucleo-144 development
board
Description
Signal
Signal
J5-1
-
-
-
J5-2
GND
GND
CN10-22
Ground
J5-3
-
-
-
J5-4
-
-
-
J5-5
-
-
-
J5-6
-
-
-
J5-7
-
-
-
J5-8
-
-
-
J5-9
-
-
-
J5-10
nRST
NRST
CN8-5
Reset
J5-11
-
-
-
J5-12
-
-
-
J5-13
-
-
-
J5-14
-
-
-
J5-15
-
-
-
J5-16
-
-
-
J5-17
-
-
-
J5-18
-
-
-
J5-19
-
-
-
J5-20
-
-
-

Host MCU Board Connections
16 Seiko Epson Corporation S5U13C00P01C100 Board User Manual
(Rev. 1.0)
S5U13C00P01C100 Board
STM32 Nucleo-144 development
board
Description
Signal
Signal
J6-1
HOST_3.3V
+3V3
CN8-7
3.3V supply
J6-2
HOST_5V
+5V
CN8-9
5V supply
J6-3
-
-
-
J6-4
GND
GND
CN10-3
Ground
J6-5
-
-
-
J6-6
HIFDE
PB6
CN10-13
Host device enable signal
J6-7
-
-
-
J6-8
HIFWR
PB2
CN10-15
Host SPI/QSPI clock
J6-9
HIFD2
PE2
CN10-25
Host SPI/QSPI D2
J6-10
-
-
-
J6-11
HIFD3
PD13
CN10-19
Host SPI/QSPI D3
J6-12
-
-
-
J6-13
-
-
-
J6-14
-
-
-
J6-15
-
-
-
J6-16
-
-
-
J6-17
-
-
-
J6-18
-
-
-
J6-19
-
-
-
J6-20
-
-
-
S5U13C00P00Cx00 Board
STM32 Nucleo-144 development
board
Description
Signal
Signal
J7-1
-
-
-
J7-2
GND
GND
CN10-5
Ground
J7-3
-
-
-
J7-4
-
-
-
J7-5
-
-
-
J7-6
-
-
-
J7-7
-
-
-
J7-8
-
-
-
J7-9
-
-
-
J7-10
-
-
-
J7-11
-
-
-
J7-12
-
-
-
J7-13
-
-
-
J7-14
-
-
-
J7-15
-
-
-
J7-16
HIFCS
PD7
CN9-2
Host INDIRECT8 chip-select
J7-17
-
-
-
J7-18
-
-
-
J7-19
-
-
-
J7-20
-
-
-

Parts List
S5U13C00P01C100 Board User Manual Seiko Epson Corporation 17
(Rev. 1.0)
8. Parts List
Item
Qty
Reference
Part
Description
Manufacturer Part No. /
Comments
1
1
CN1
HEADER 2X8
CONN HEADER 16POS (2x8) 0.1” right-
angle
Amphenol FCI 68021-216HLF
2
1
CN2
CONN_FLEX_24
CONN FPC/FFC 24POS 0.50MM pitch
Panasonic AYF532435
3
10
C0,C1,C4,C5,C6,C7,C8,C9,
C12,C31
1uF
1.0uF Ceramic -20%/+80% 25V Y5V C0805
Samsung CL21F105ZAFNNNE
4
2
C3,C11
4.7uF
4.7uF Ceramic 10% 25V X7S C0805
Samsung CL21Y475KAFNNNE
5
1
C10
10uF
10uF Ceramic 10% 25V X5R C0805
Samsung CL21A106KAYNNNE
6
1
C13
3.3uF
3.3uF Ceramic 10% 10V X5R C0805
Samsung CL21A335KPFNNNE
7
4
C14,C16,C22,C23
0.1uF
0.1uF Ceramic 10% 50V X7R C0603
Samsung CL10B104KB8NNNC
8
20
C15,C17,C18,C19,C20,C21,
C26,C27,C28,C29,C30,C32,
C33, C35,C36,C37,C38,C39
C40,C41
1uF
1uF Ceramic -20%/+80% 25V Y5V C0805
Samsung CL21F105ZAFNNNE
9
2
C24,C25
Not mounted
10pF Ceramic 0.25pF 50V C0G/NP0 C0603
Samsung CL10C100CB8NNNC
10
3
D1,D2,D3
DIODE_SCHOTTKY
Diode Schottky 30V 500mA SOD123
ON Semi MBR0530
11
1
D4
DIODE
Diode Schottky 30V 200mA SOD123
Micro Commercial BAT42W-TP
12
3
JP2,JP3,JP4
HEADER 1X2
CONN HEADER 2POS 0.1"
Honda Tsushin FFC-52AMEP1-2P
13
2
JP6,JP7
HEADER_1X3
CONN HEADER 3POS 0.1"
Honda Tsushin FFC-52AMEP1-3P
14
4
J4,J5,J6,J7
HEADER_10X2
CONN HOUSING 20POS 2.54MM DUAL
Hirose HIF3H-20DA-2.54DSA(71)
15
1
J8
Not mounted
CONN HEADER 18POS (2x9) 0.1”
Hirose A1-18PA-2.54DSA(71)
16
1
J9
Not mounted
CONN HEADER 4POS 0.1"
Honda Tsushin FFC-52AMEP1-4P
17
1
J10
Not mounted
CONN HEADER 2POS 0.1"
Honda Tsushin FFC-52AMEP1-2P
18
1
LED1
LED +3.3V Green
LED GREEN DIFFUSED 1608 SMD
Stanley Electric BG1111C-TR
19
1
L1
10uH
10uH 510mA 540mOhm wirewound inductor
Taiyo Yuden NR3010T100M
20
1
Q3
N-CH FET
MOSFET N-CH 30V 3.2A SOT23
ON Semi NTR4170NT1G
21
1
R3
0.47
0.47 OHM 5% 1/10W R0603
Stackpole RMCF0603JTR470
22
27
R4,R5,R6,R7,R9,R10,R11,
R12,R13,R16,R20,R21,R24,
R25,R29,R33,R34,R35,R36,
R37,R38,R39,R40,R43,R45,
R46,R49
0
0 OHM 1/10W R0603
Stackpole RMCF0603ZT0R00
23
3
R8,R19,R31
10K
10K OHM 1% 1/10W R0603
Stackpole RMCF0603FT10K0
24
2
R14,R26
10
10 OHM 1% 1/10W R0603
Stackpole RMCF0603FT10R0
25
1
R15
100K
100K OHM 5% 1/10W R0603
Stackpole RMCF0603JT100K
26
1
R18
1K
1K OHM 5% 1/10W R0603
Stackpole RMCF0603JT1K00
27
1
R41
560
560 OHM 5% 1/10W R0603
Stackpole RMCF0603JT560R
28
2
R47,R48
Not mounted
10K OHM 5% 1/10W R0603
Stackpole RMCF0603JT10K0
29
5
SH2,SH3,SH4,SH6,SH7
JUMPER
SHUNT BLACK 1x2 0.1”
Omron XJ8A-0211
30
1
SW1
SW TACT
SWITCH TACTILE SPST-NO 0.05A 16V
Alps SKRPABE010
31
1
SW2
SW TACT
SWITCH TACTILE SPST-NO 0.05A 24V
Omron B3FS-1010P
32
1
U1
S1D13C00
Epson S1D13C00 TQFP13-64
Epson S1D13C00L00C000
33
1
U2
IS25LP-128
16Mbytes SPI Flash Memory
ISSI IS25LP128-JBLE
34
1
U4
MCP1700
3.3V LDO
Microchip MCP1700T-3302E/TT
35
1
Y1
FC-135
32.768KHz Crystal
Epson FC-135 32.7680KA-K

S5U13C00P01C100 Schematics
18 Seiko Epson Corporation S5U13C00P01C100 Board User Manual
(Rev. 1.0)
9. S5U13C00P01C100 Schematics
S5U13C00P01C100 Schematics (1 of 2)