Epson S5U13781R00C100 User manual

SEIKO EPSON CORPORATION Rev. 1.0
S5U13781R00C100
Reference Board User Manual
Document Number: X94A-G-004-01
Status: Revision 1.0
Issue Date: 2012/03/26

Page 2
S5U13781R00C100 Reference Board User Manual X94A-G-004-01
Revision 1.0 Issue Date: 2012/03/26
Seiko Epson Corporation
Evaluation board/kit and Development tool important notice
1. This evaluation board/kit or development tool is designed for use for engineering evaluation,
demonstration, or development purposes only. Do not use it for other purpose. It is not intended to
meet the requirement of design for finished product.
2. This evaluation board/kit or development tool is intended for use by an electronics engineer, and it is
not a consumer product. The user should use these goods properly and safely. Seiko Epson dose not
assume any responsibility and liability of any kind of damage and/or fire caused by usage of it. The
user should cease to use it when any abnormal issue occurs, even during proper and safe use.
3. The parts used for this evaluation board/kit or development tool may change without notice.
NOTICE
No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko
Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any
liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or
circuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such as,
medical products. Moreover, no license to any intellectual property rights is granted by implication or otherwise, and there is no
representation or warranty that anything made in accordance with this material will be free from any patent or copyright
infringement of a third party. This material or portions thereof may contain technology or the subject relating to strategic
products under the control of the Foreign Exchange and Foreign Trade Law of Japan and may require an export license from the
Ministry of Economy, Trade and Industry or other approval from another government agency.
All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective companies.

Page 3
X94A-G-004-01 S5U13781R00C100 Reference Board User Manual
Issue Date: 2012/03/26 Revision 1.0
Seiko Epson Corporation
©SEIKO EPSON CORPORATION 2012, All rights reserved.
Table of Contents
1Introduction......................................................................................................................... 5
2Features ............................................................................................................................. 6
3Board Settings.................................................................................................................... 7
3.1 CNF[2:0] Configuration .................................................................................................................7
3.2 Jumper setting...............................................................................................................................8
3.3 Power Supply................................................................................................................................9
3.3.1 VDDCORE ............................................................................................................................9
3.3.2 LED Back Light LED+/LED- Power Supply...........................................................................9
4Connectors ........................................................................................................................10
4.1 J4 Host Interface Connector .......................................................................................................10
4.2 J5 Panel Interface Connector......................................................................................................10
4.3 J8 ～J9 Connectors for Panel Connection................................................................................11
5Others................................................................................................................................12
5.1 Quartz-Crystal Resonator for CLKI.............................................................................................12
5.2 SPI flash memory........................................................................................................................12
6Parts list.............................................................................................................................13
7Schematic Diagram............................................................................................................14
8Board Layout and Dimensions...........................................................................................16
9References ........................................................................................................................19
10 Change Record..................................................................................................................20

Page 4
S5U13781R00C100 Reference Board User Manual X94A-G-004-01
Revision 1.0 Issue Date: 2012/03/26
Seiko Epson Corporation

Page 5
X94A-G-004-01 S5U13781R00C100 Reference Board User Manual
Issue Date: 2012/03/26 Revision 1.0
Seiko Epson Corporation
1 Introduction
This manual describes the setup and operation of the S5U13781R00C100 reference board.
The reference board is designed as an evaluation platform for the S1D13781 Display Controller. The
S5U13781R00C100 reference board has host controller connector, LCD panel connector, clock generator,
SPI flash memory (16Mbit), power regulation circuit for S1D13781 core and DC/DC converter for LED
back light.
This user manual is updated as appropriate. Please check the Seiko Epson Website at
http://www.epson.jp/device/semicon_e/product/lcd_controllers/index.htm for the latest revision of this
document before beginning any development.
We appreciate your comments on our documentation. Please contact us via email at
[e-mail].

Page 6
S5U13781R00C100 Reference Board User Manual X94A-G-004-01
Revision 1.0 Issue Date: 2012/03/26
Seiko Epson Corporation
2 Features
The S5U13781R00C100 reference board includes the following features:
QFP 100pin S1D13781F00A100 Display Controller
2.54mm pitch vias for host bus interface header
2.54mm pitch vias for LCD panel header
Connection area with 2.54mm pitch vias for header and FPC (0.5mm pitch 55 electrode)
connector to connect LCD panel.
On-board 24MHz crystal
On-board voltage booster for LED back light (38V 60mA Maximum output at 5V input)
On-board voltage regulator with 1.5V output from 3.3V/5.5V input for COREVDD and
PLLVDD for the S1D13781
On-board 16Mbit SPI NOR FLASH standard memory

Page 7
X94A-G-004-01 S5U13781R00C100 Reference Board User Manual
Issue Date: 2012/03/26 Revision 1.0
Seiko Epson Corporation
3 Board Settings
3.1 CNF[2:0] Configuration
The S1D13781 has three configuration inputs, CNF[2:0], which are used to configure the S1D13781 host
interface type as described in Table 3-1, Signal Allocation for Host Interface.
The S5U13781R00C100 reference board defaults to the SPI interface (the default setting for CNF[2:0] =
111).
Table 3-1 Signal Allocation for Host Interface
S1D13781
Pin name
Direct 16bit
Mode 1
Direct 16bit
Mode 2
Indirect 16bit
Mode 1
Indirect 16bit
Mode 2
Direct 8bit
Indirect 8bit
SPI
CNF[2:0]
000
001
010
011
100
101
111
CS#
CS#
CS#
CS#
CS#
CS#
CS#
SCS#
WR#
WR#
RDU#
WR#
RDU#
WR#
WR#
SCK
RD#
RD#
RDL#
RD#
RDL#
RD#
RD#
H
UB#
UB#
WRU#
UB#
WRU#
H
H
H
LB#
LB#
WRL#
LB#
WRL#
H
H
H
AB0
TE
TE
TE
TE
AB0
TE
TE
AB1
AB1
AB1
P/C#
P/C#
AB1
P/C#
Low
AB[18:2]
AB[18:2]
AB[18:2]
Low
Low
AB[18:2]
Low
Low
DB0
DB0
DB0
DB0
DB0
DB0
DB0
SI
DB1
DB1
DB1
DB1
DB1
DB1
DB1
SO
DB[7:2]
DB[7:2]
DB[7:2]
DB[7:2]
DB[7:2]
DB[7:2]
DB[7:2]
L
DB8
DB8
DB8
DB8
DB8
TE
L
L
DB[15:9]
DB[15:9]
DB[15:9]
DB[15:9]
DB[15:9]
L
L
L
Notes:
“H” means direct connection to IOVDD
“L” means direct connection to GND
“Low” means internal pull-down for address bus active
TE is determined by REG[22h] Display Settings Register bits 6-5

Page 8
S5U13781R00C100 Reference Board User Manual X94A-G-004-01
Revision 1.0 Issue Date: 2012/03/26
Seiko Epson Corporation
3.2 Jumper setting
The S5U13781R00C100 reference board includes jumpers which control the functions described in Table
3-2, Jumper settings. For jumper locations on the reference board, see Figure 3-1, Jumper Pin Locations.
Table 3-2 Jumper Settings
Function
Jumper
Settings
Description
Power supply for FLASH memory
J1 1-2
2
3
Supply VDDIO to U2(FLASH-VCC)
External power supply to U2（FLASH-VCC）
GND
CNF/RESET setting
J2 1-2
3-4
5-6
7-8
CNF0 Short: CNF0=0, Open: CNF0=1
CNF1 Short: CNF1=0, Open: CNF1=1
CNF2 Short: CNF2=0, Open: CNF2=1
RESET Short: RESET=0, Open: RESET=1
Setting for back light LED regulator
J3 1-2
3-4
5-6
7-8
Short: Enables regulator
Short: Regulator output current +20mA
Regulator output current +20mA
Regulator output current +20mA
Power supply for VDDIO /
VDDDCDC
J4 3
4
External power supply to VDDIO
External power supply to VDDDCDC
On board OSC setting
J6 1-2
Short: Disable on board OSC
On board OSC input
J7 1
External clock input in case of OSC disable
Figure 3-1 Jumper Pin Locations
J3
J2
J6
J1
J4

Page 9
X94A-G-004-01 S5U13781R00C100 Reference Board User Manual
Issue Date: 2012/03/26 Revision 1.0
Seiko Epson Corporation
3.3 Power Supply
The S5U13781R00C100 reference board is designed to supply VDDCORE (1.5V) and LED back light
power (LED+/LED-) from the 2.7V to 5.5V input of J4-4 (VDD DCDC).
The voltage output of 2.7V to 3.3V from J4-3 (VDDIO) is used for the U4 (S1D13781 Display
Controller) power supply, D2 (LED indicator) and Y1(SG-310SCF 24MHz OSC).
The power for U2 (M25P-16-VMN6P SPI flash memory) is supplied via J1-2 (FLASH-VCC).
3.3.1 VDDCORE
VDDCORE (1.5V) is generated from U1 (BU15TD3WG Voltage regulator) and is used to supply power
to COREVDD and PLLVDD of U4 (S1D13781 Display Controller).
3.3.2 LED Back Light LED+/LED- Power Supply
The LED back light power supply (Maximum voltage between LED+ and LED- is 38V) is generated by
U3 (TPS61161A voltage booster).
The output current is set by J3 as described in Table 3-2, Jumper Settings. Connecting one of J3 3-4, J3 5-
6 or J3 7-8 allows 20mA, connecting any two of them allows 40mA and connecting all of them allows
60mA output, maximum.
Table 3-3 Power Supply for S5U13781R00C100
Power Supply
Usage
Voltage Range
VDDIO
Input
IOVDD for U4 (S1D13781 Display Controller)
Power supply for Y1 （SG-310SCF 24MHz OSC）
Power supply for D2(SML-E12M8WT86 LED)
2.7V ～3.6V
VDDDCDC
Input
Power supply for U1 (BU15TD3WG 1.5V LDO regulator）
Power supply for U3(TPS61161A voltage booster)
2.7V ～5.5V
FLASH-VCC
Input
Power supply for U2(M25P16-VMN6P SPＩflash memory
2.7V ～3.6V
VDDCORE
Output
COREVDD and PLLVDD for U4 (S1D13781 LCD
controller)
1.5V (Fixed)
LED+ / LED-
Output
LED back light power supply
VDDDCDC ～38V
Note: Do not short the power supply pins to any other pins.

Page 10
S5U13781R00C100 Reference Board User Manual X94A-G-004-01
Revision 1.0 Issue Date: 2012/03/26
Seiko Epson Corporation
4 Connectors
The S5U13781R00C100 reference board has via for host interface and panel interface connectors (J4, J5,
J8, J9 and J10).
To locate of these connectors on the reference board, see Figure 4-1, Reference Board Connector
Locations.
Figure 4-1 Reference Board Connector Locations
4.1 J4 Host Interface Connector
The host interface pins of S1D13781 are connected to J4 of the S5U13781R00C100 reference board. See
Figure 7-1, S5U13781R00C100 Schematic Diagram (1 of 2), and Figure 7-2, S5U13781R00C100
Schematic Diagram (2 of 2), for detailed pin allocation.
4.2 J5 Panel Interface Connector
The panel interface pins of the S1D13781 are connected to J5 of the S5U13781R00C100 reference board.
See Figure 7-1, S5U13781R00C100 Schematic Diagram (1 of 2), and Figure 7-2, S5U13781R00C100
Schematic Diagram (2 of 2), for detailed pin allocation.
J8
J9
J10
J5
J4

Page 11
X94A-G-004-01 S5U13781R00C100 Reference Board User Manual
Issue Date: 2012/03/26 Revision 1.0
Seiko Epson Corporation
4.3 J8 ～J9 Connectors for Panel Connection
J8 through J10 on the S5U13781R00C100 reference board are standard connectors used to implement
suitable connection for various LCD panels.
J8 is a 0.5mm pitch FPC connector (FH28-55S, bottom electrode type). See Figure 7-1,
S5U13781R00C100 Schematic Diagram (1 of 2), and Figure 7-2, S5U13781R00C100 Schematic Diagram
(2 of 2), for detailed pin allocation.

Page 12
S5U13781R00C100 Reference Board User Manual X94A-G-004-01
Revision 1.0 Issue Date: 2012/03/26
Seiko Epson Corporation
5 Others
5.1 Quartz-Crystal Resonator for CLKI
S5U13781R00C100 reference board includes Y1 (SG-310SCF 24MHz oscillator) for the CLKI input of
the S1D13781.
The output of the oscillator is disabled by connecting J6 1-2 and enabled by disconnecting.
5.2 SPI flash memory
The S5U13781R00C100 reference board includes SPI NOR FLASH standard memory of 16Mbit
capacity. It can be used as external image data storage for the S1D13781.

Page 13
X94A-G-004-01 S5U13781R00C100 Reference Board User Manual
Issue Date: 2012/03/26 Revision 1.0
Seiko Epson Corporation
6 Parts list
Table 6-1 S5U13781R00C100 Bill of Materials
No.
Qty
Reference
PKG
Size
Pin
Part
Description
Manufac
turer
1
1
U4
TQFP
14.0x14.0x1.7
100
S1D13781
LCD Controller
EPSON
2
1
Y1
3225
3.2x2.5x1.2
4
SG-310SCF
OSC 24MHz
EPSON
3
1
U3
QFN2ｘ2
2.1x2.1x0.8
6
TPS61161ADRVT
LED Driver
TI
4
1
U1
SSOP5
3.1x3.0x1.25
5
BU15TD3WG
Regulator LDO
ROHM
5
1
L1
5050
5.0x5.0x2.0
2
VLCF5020T-220MR75-1
Inductor 22uH
TDK
6
1
D1
3516
3.5x1.6.1.0
2
CRS04
SBD
TOSHIBA
7
1
D2
1608
1.6x0.8x0.36
2
SML-E12M8WT86
LED
ROHM
8
1
U2
SO8N 6x5
5.0x6.2x1.75
8
M25P16-VMN6P-ND
SPI NOR-
FLASH 16Mb
Micron
9
1
J8
Bottom
electrode
32.0x6.5x2.55
55
FH28-55S-0.5SH(05)
FPC Connector
55P
HIROSE
10
1
C18
2125
2.0x1.25x1.25
2
GRM21BB31H105KA12L
Capacitor 1.0uF
50V/JB
MURATA
11
1
C17
1608
1.6x0.8x0.8
2
GRM188B31E105KA75D
Capacitor 1.0uF
25V/JB
MURATA
12
2
C2,C14
1608
1.6x0.8x0.8
2
GRM188B31E474KA75D
Capacitor
0.47uF 25V/JB
MURATA
13
1
C16
1608
1.6x0.8x0.8
2
GRM188B31E224KA87D
Capacitor
0.22uF 25V/JB
MURATA
14
14
C1,C3,C4,C5,
C6,C7,C8,C9,
C10,C11,C12,
C13,C15,C19
1005
1.0x0.5x0.5
2
GRM155B31C104KA87D
Capacitor 0.1uF
16V/JB
MURATA
15
7
R5,R6,R7,R8,
R9,R10,R11
1608
1.6x0.8x0.45
2
RK73H1JTTD4702F
Resistor 47K
ohm
KOA
16
1
R15
1608
1.6x0.8x0.45
2
RK73H1JTTD3300F
Resistor 330
ohm
KOA
17
3
R12,R13,R14
2125
2.0x1.25x0.5
2
RK73H2ATTD10R0F
Resistor 10 ohm
1%
KOA
18
4
R1,R2,R3,R4
1608
1.6x0.8x0.45
2
RK73Z1JTTD000
Resistor 0 ohm
KOA

Page 14
S5U13781R00C100 Reference Board User Manual X94A-G-004-01
Revision 1.0 Issue Date: 2012/03/26
Seiko Epson Corporation
7 Schematic Diagram
Figure 7-1 S5U13781R00C100 Schematic Diagram (1 of 2)

Page 15
X94A-G-004-01 S5U13781R00C100 Reference Board User Manual
Issue Date: 2012/03/26 Revision 1.0
Seiko Epson Corporation
Figure 7-2 S5U13781R00C100 Schematic Diagram (2 of 2)

Page 16
S5U13781R00C100 Reference Board User Manual X94A-G-004-01
Revision 1.0 Issue Date: 2012/03/26
Seiko Epson Corporation
8 Board Layout and Dimensions
Figure 8-1 S5U13781R00C100 Board Layout Silk Screen

Page 17
X94A-G-004-01 S5U13781R00C100 Reference Board User Manual
Issue Date: 2012/03/26 Revision 1.0
Seiko Epson Corporation
Figure 8-2 S5U13781R00C100 Board Layout Top View
Figure 8-3 S5U13781R00C100 Board Layout Bottom View

Page 18
S5U13781R00C100 Reference Board User Manual X94A-G-004-01
Revision 1.0 Issue Date: 2012/03/26
Seiko Epson Corporation
Figure 8-4 S5U13781R00C100 Board Dimensions (units: mm)

Page 19
X94A-G-004-01 S5U13781R00C100 Reference Board User Manual
Issue Date: 2012/03/26 Revision 1.0
Seiko Epson Corporation
9 References
Epson Research and Development, Inc., S1D13781 Hardware Functional Specification, document number
X94A-A-001-xx.

Page 20
S5U13781R00C100 Reference Board User Manual X94A-G-004-01
Revision 1.0 Issue Date: 2012/03/26
Seiko Epson Corporation
10 Change Record
X94A-G-005-01 Revision 1.0 - Issued: March 26, 2012
Release document as rev 1.0