ErgoAV ERMMS1 -01 B User manual

Motion TV Mount Instruction Manual (A)
English pages: 02-15 French pages: 16-29 Spanish pages: 30-43
Model: ERMMS1 -01 B
THANK YOU FOR CHOOSING THIS ERGOAV PRODUCT!
At ErgoAV, we want to add value to your AV experience by providing the highest
quality products and services in the industry.
If you have any concerns or
comments, please contact us.
ErgoAV Customer Care
phone[phone]
email: [email protected]
website: .ergoav.com
address: 9501 Louisiana Ave
N, #200, Brooklyn Park, MN 55445

IMPORTANT SAFETY INFORMATION
A DANGER! Please carefully read all instructions before attempting installation. If
you do not understand the instructions or have any concerns or questions, please
contact our Technical Support line
at (877) 419- 7832 or customer service at
[email protected].
A CAUTION: Use with products heavier than the maximum weights indicated may
result
in instability causing possible injury.
• Do not use this product
for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are
not liable for damage or injury
caused by improper mounting, incorrect assembly
or inappropriate use.
• This product is designed
for use in wood stud, and solid concrete walls. - DO
NOT install into drywall alone.
• The wall must be capable
of supporting four times the weight of the TV and
mount combined.
• Use this mounting system only
for its intended use as described in these
instructions. Do not use attachments not recommended by the manufacturer.
• Do not use outdoors.
• Route cords and cables properly
to avoid mechanical damage.
•
SAVE THESE INSTRUCTIONS
Weight Restrictions
•
MAX
44 lbs/
19.9 kg
If your TV weighs more, do not
use this product.
A WARNING
DO NOT exceed the maximum weight indicated. This mounting
system is intended
for use only within the maximum weights
indicated. Use with products heavier than the maximum weights
indicated may result in failure
of the mount and its accessories,
causing damage and
or injury.
Check the VESA Pattern of Your TV before the Installation
=
=
~ .
~ E
~ E
~ 0
•
~ 0
mi. --· ..-----
75 mm~ 3 in
100 mm~ 4 in
200 mm ~ 7 7 /8 in
Minimum: 75mm x 75mm / 3" x 3" (W x H)
Maximum: 200mm x 200mm / 7 7 /8" x 7 7 /8" (W x H)
If your TV's VESA Pattern is smaller than 75mm x 75mm or greater than
200mm x 200mm, this mount is NOT COMPATIBLE with your
TV. Please contact our
Technical Support at [phone] or [email protected] to find a compatible
mount.
02

Tools Needed (Not Included)
I.
Stud Finder Awl Tape Measure Pencil Electric Drill Phillips
Level Screwdriver
/
7/32in(5.5mm) 3/8in( 10mm) 1 /2in( 13mm)
Wood Drill Socket Wrench Socket Wrench
Verify Your Wall Construction
CAUTION
DO NOT
install into
drywall alone
(Needed for concrete installs)
~
3/8in( 10mm)
Concrete Drill Hammer
Wood Studs
(with Drywall) Solid Concrete
Wall
If you are not sure of
the wall construction,
please contact our
Technical Support line
at [phone] or
customer service at
[email protected].
Supplied Parts and Hardware
A WARNING: This product contains small items that could be a choking hazard if
swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use
damaged or defective parts. If you require replacement parts, please contact our
Technical Support line at [phone] or customer service at [email protected]
to fmd a compatible mount.
• PLEASE NOTE: Not all hardware included in this package will be used.
Supplied Parts and Hardware for Step 1
ml x1
DE x4
Faceplate Extender Bracket
03
Bolt
M6 x 12mm
[H1] X4
Nut
M6
[H2] X4

Step1 Choose the Combination that Fits Your VESA Hole Pattern
-
E -
E
E E
0
LO
0 r"
--
-C
C ·-
~
C')
NOTE:
4in(100mm)
3in(75mm)
(E 3)
~mil~
(E
:3) 0 0
For VESA hole pattern:
3 x 3in/75 x 75mm
4 x 4in/100 x 100mm
The small bump on the extender bracket [02] should be aligned with the hole on the
faceplate [01 ].
Please do not firmly tighten the bolts [H1] and nuts [H2] until the step 2 is finished.
Fig. 1 For VESA Hole Pattern: 8 x Bin/200 x 200mm
-
E
E
0
0
C\I
-
C
·-
00
8in(200mm)
04

Fig. 2 For VESA Hole Pattern: 4 x Bin/100 x 200mm
-
E
E
0
0
C\I
-
C
·-
co
4in(100mm)
(]
0
Fig. 3 For VESA Hole Pattern: 8 x 4in/200 x 100mm
-E ~----f'
E
0
0
-
-
C
8in(200mm)
~ --"'---+--,-,---+
'----..LL.-=-'
0
Supplied Hardware for Step 2
DJl Washers Dla Spacers [If needed]
i NOTE: The washers and spacers are shown in actual size !
~------------------------------------------------------------------------------------------------~
[B1] x4
M4/M5
M4
[B2] x4
M6/M8
[G1] x4
8.5x1 8x2.5mm [G2] x8 8.5x18x1 0mm
~ TV Bolts [Only one bolt size fits your TV]
NOTE: The bolts are shown in the actual size
o--
M4 x 12mm
[C1] x4
05
~
M4 x 30mm
[C2] x4