Ergoswiss ST 700A User manual

ASSEMBLY INSTRUCTIONS
for Screenlift ST 700A and 1000A
Art. Nr. 198.00156
Page 1/8
Edition: 11.2016
PARTS INCLUDED WITH YOUR SCREENLIFT
# 1 Screenlift ST 1000A / ST 700A
# 2 Lid lifter
# 3 Lift brackets
# 4 TV mounting brackets ( ST 1000A only)
# 5 R.F. Module
# 6 Remote control
# 7 AC input wire
# 8 Power supply bracket
# 9 Rocker switch
# 10 Power supply

ASSEMBLY INSTRUCTIONS
for Screenlift ST 700A and 1000A
Art. Nr. 198.00156
Page 2/8
Edition: 11.2016
CAUTION
Before you begin any of the Installation procedures, read and follow the warnings and safety
instructions. Only person that read these instructions are allowed to operate the Screen lift.
SAFETY INSTRUCTIONS
Use the following safety guidelines to help protect your lift from potential damage and to ensure your own
personal safety.
Read and follow all safety instructions
Read all the installation instructions before testing or installing your lift
Keep remote control out of reach of children
To prevent bodily injury keep hands and clothing away from the lift while it is in operation
Before installing the lift or working with it’s connections, unplug the lift from the electrical shock
If the Lift is mounted in furniture, please take care that no clamping borders and no danger of
squeezing can be generated. Please watch the CEE Directions for machine and make a risk analysis
Do not install the lift, power supply or R.F. module in places subject to extreme temperatures for
example near a radiator, or heating vent
To avoid damaging the power supply, R.F. module and power cord, do not put anything on it or
place it where it could become damaged
Unplug the lift in the following conditions:
oWhen the power cord or plug is damaged or frayed
oIf liquid has spilled into the lift, power supply or RF module
oIf the lift, power supply or RF module has been exposed to rain or water
oIf the lift exhibits a distinct change in performance, indicating a need for servicing

ASSEMBLY INSTRUCTIONS
for Screenlift ST 700A and 1000A
Art. Nr. 198.00156
Page 3/8
Edition: 11.2016
FUNCTION CONTROL
Remove all contents from packaging and compare with the listed parts. Test the function of the Screen lift
as follows: (refer to the sketch on page 1):
oConnect the cable of the Screen lift (# 2) to the control box (# 3)
oConnect the cable of the control box (# 3) to the power supply (# 4)
oConnect the cable of the rocker switch to the control box (# 3)
oConnect the net cable of the power supply (# 4)
oPut the Screen lift (# 2) in an vertical position
oPress the rocker switch, drive a few centimetres up and back again. The switch has to be pressed
always due of security reasons. By releasing the switch, the screen lift will stop immediately
oPress the remote control (+), drive a few centimetres up and back (-) again. The switch has to be
pressed always due of security reasons. By releasing the switch, the screen lift will stop immediately
PLEASE NOTE:
During the lifting process (up and down) the Screen lift has always been controlled by eye. If
there is a danger, the lift has to be stopped immediately.
MAIN MEASURES ST 100A

ASSEMBLY INSTRUCTIONS
for Screenlift ST 700A and 1000A
Art. Nr. 198.00156
Page 4/8
Edition: 11.2016
MAIN MEASURES, ST 700A

ASSEMBLY INSTRUCTIONS
for Screenlift ST 700A and 1000A
Art. Nr. 198.00156
Page 5/8
Edition: 11.2016
ASSEMBLY OF THE SCREENLIFT
oPlace the Screen lift (# 1) vertically (use a level) on the back panel of the cabinet in a location that
will allow full up and down movement of the TV. Use the intended fixing hole on the sides of the
Screen lift. The Screen lift has to be mounted about 4mm below the furniture border.
oAttach the power supply (# 10) with the power supply bracket (#8). Please follow the drawing on
page 1, the power supply needs to be mounted on the right side of the Screen lift.
oAttach the R.F. module (# 5) next to the power supply (# 10). Take care that the wires have enough
space that they cannot get caught.
oTo attach the Rocker Switch (# 9), you have to drill a hole at the designated position. Than press
the Rocker Switch in. Take care that the wires have enough space that they cannot get caught.
Attach the wires with cable clips.
oConnect the cable of the control box (# 3) to the power supply (# 10)
oConnect the cable of the rocker switch to the control box (# 5)
oConnect the net cable of the power supply (# 10)
oMove the TV mounting brackets (# 4) above the Lift brackets (# 3).
oAdjust the TV mounting brackets for your TV and attach it to the TV. Make sure the TV is attached
centrically to the mounting brackets.
oDrive the Screen lift (# 1) to its upper position.
oPlace the TV on wanted position and attach the lift brackets to the Screen lift.
oDrive down the Screen lift with the attacked TV. Take care that the TV cannot get jammed some-
where and that it breaks in completely to the furniture.
oAttach the Lid lifter (# 2) with the bended end to the direction of the front side into the groove of
the Screen lift. The Lid lifter has to stand over the TV.
oDrive again to the upper position an tight all screws.
Background for this direction is the characteristic of the assembly into a cabinet.
PLEASE TAKE CARE, THAT:
During operation, no hands and clothing can be kept in the function area of the Screen lift
No clamping borders and no danger of squeezing can be generated. Please watch the CEE
Directions for machine and make a risk analysis

ASSEMBLY INSTRUCTIONS
for Screenlift ST 700A and 1000A
Art. Nr. 198.00156
Page 6/8
Edition: 11.2016
USER INSTRUCION, RF REMOTE SYSTEM
INSTALLATION
oConnect the power supply and the motor unit to the remote receiver. Two different
plug sizes make this connection only possible to make it in the right way
oAfter having connected the plugs, the blue light will be light.
oPush the emitter buttons and the motor unit will move up and down.
oThe button has to be pushed while the Screen lift is operating.
LEARNING
oIf the remote receiver does not respond when pushing the emitter buttons, reset the
receiver. After that, code the emitter an receiver together again.
CODING
oPush the learner button on the receiver for less than 1 second
oPush one of the emitter buttons
oThe red light will start flashing
oPus one oft he emitter buttons again and the red light will turn off
oThe units now are ceded together with a unique code
RESET
oPush and hold down the learner button on the receiver for 10 seconds. (will be reset
when the red light turns off)

ASSEMBLY INSTRUCTIONS
for Screenlift ST 700A and 1000A
Art. Nr. 198.00156
Page 7/8
Edition: 11.2016
OPERATED BY ROCKER SWITCH
oBy pressing the switch upside the Screenlift will drive up
oBy pressing the switch downwards the Screenlift will drive down
The button has to be pressed during the whole lifting or lowering process due of security reasons. By
releasing the switch, the screen lift will stop immediately
PLEASE NOTE:
During operation (up and down) the Screen lift has always been controlled by eye. If there is
a danger, the lift has to be stopped immediately.
ADJUSTING THE STROKE LENGTH OF THE LIFT
Adjusting the bottom stop
The bottom stop can be adjusted to any prefferred height, e.g. if you do not want the lift to go all the way
down into the cabinet.
1. Remove the 2 covers
2. Use an allen key to loosen the screw of the wire
glider. Move the glider to the preferred
position and tighten the screw securely again.
3. Mount the 2 covers again.

ASSEMBLY INSTRUCTIONS
for Screenlift ST 700A and 1000A
Art. Nr. 198.00156
Page 8/8
Edition: 11.2016
Adjusting the top stop
The top stop can be adjusted to any preferred height, e.g. if you do not want the lift to go all the way out of
the cabinet.
Use an allen key to loosen the screw of the
wire glider. Move the glider to the preferred
position and tighten the screw securely again.
SALES ORGANISATION
Ergoswiss AG
Nöllenstrasse 15
9443 Widnau
Schweiz
T: 0041 71 727 06 70
F: 0041 71 727 06 79
M: [e-mail]
www.ergoswiss.com
The information in this document is subject to change without notice.