Ergotron StyleView SV42 User manual

1/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
Estimated Completion Time
60
minutes
1x
Lift Engine Replacement for Carts powered with SLA
5/32" (4mm) 13mm
4Remove monitor.
123
Turn o all mounted equipment. Disconnect Power System
from power source.
Turn power system o by
holding down the AC Outlet
Power button for 1 - 3 seconds.
Power light will shut o.
5Remove front base cover.
WARNING
Impact Hazard!
Moving Parts can Crush and Cut.
Raise monitor to top of vertical
adjustment BEFORE removing.
Failure to heed this warning may result in
serious personal injury or property damage!
822-310

2/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
7Remove power module
6Remove rear base cover.
Loosen T-Slot retainer
bracket and slide up. Do
not remove screw, only
loosen.
a
bCut the table tie.

3/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
8Remove brackets, cam cover and cable routing channels
ab
cDetach all cables from power module.
dRemove power module.

4/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
cd
Remove basket and handle.
180˚
ab
c
9

5/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
12 Remove ground wire if present, then remove the four screws and Arm or Lift.
If removed, save the star washer from the ground wire for reattachment.
5/32" (4mm)
11 Unlock CPU and remove all contents in the storage area.
10 Open worksurface.
13 Unplug all cables from the USB hub.

6/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
14 Remove left rear worksurface portion and save for attachment to the new head unit.
If present, disconnect the two UI cables and pull them down and out through the bottom of the head unit.
16
a
Remove drawer keypad if present.
Remove drawer controller cover.
15

7/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
b
c
Unplug all cables from drawer controller.
Pull cable up into storage area. dDisconnect power cable.

8/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
Slide bottom cabinet o.
17
a
b
c
Remove bottom drawer cabinet. If you do not have a bottom drawer
- continue to step 18.
Unscrew the bottom cabinet 2x
M4 x 12mm
Remove the top drawer(s).

9/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
18
19 Disengage brake cable.
aRemove brake cover.
ab
c
Remove drawer cabinet. If you do not have a drawer - continue to step 19.

10/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
c
b
Remove ball end of cable from brake.
Loosen nut.
13mm
20 Remove the bottom 2 screws from the head unit.

11/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
ab
5/32" (4mm)
22 Unscrew and remove lift engine.
21
c
Loosen screws
Remove screws.
Lift head unit o

12/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
24
25
Insert two screws and leave
them protruding to allow
head unit to hang on them.
Attach the two bottom screws and then tighten top two screws.
M6 x 30mm
2x
5/32" (4mm)
Insert new lift engine and screw in.
23
abHang head unit on screws.

13/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
a
bc
d
26 Engage brake cable.
Insert ball end of cable into brake.
Tighten cable tension
(do not tigthten nut at this time).
tighten nut.
Replace brake cover.
13mm

14/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
28
a
Slide the bottom drawer cabinet only halfway onto the bottom tracks of the top
drawer. If you do not have a bottom drawer - skip to step 29.
27
ab
c
Attach drawer cabinet to lift engine. If you do not have a drawer
- skip to step 30.
bPlug the bottom drawer cable into the
top drawer interface.

15/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
Plug in drawer keypad cable, and USB cable.
Slide bottom drawer on
all the way.
c
aPull cable down through storage area.
d2x
M4 x 12mm
b
Screw in bottom cabinet.
29
30
Slide all drawers into the cabinet.

16/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
31
32
If you disconnected the 2 UI cables, route them up into the new head unit and connect to
the left rear worksurface portion you previously removed.
b
Replace drawer controller cover.
a
Reconnect power cable.
a

17/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
Attach the left rear worksurface portion to the new head unit.
33 Plug in all cables from the USB hub.
34 Reattach arm or lift with the 4 screws and ground wire with star washer.
5/32" (4mm)
b

18/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
35
ab
c
Replace basket and handle.
Attach cable routing cables, cam cover and brackets
36
ab
cd

19/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
37 Install power module
aPlace power module in base.
bAttach all cables from power module.
cLoosen T-Slot retainer
bracket and slide down.
Do not remove screw, only
loosen.

20/21
888-05-051-G-00 rev. A • 02/15
Tech Sheet
StyleView SV42 SLA, LCD
39
38
Replace front base cover.
Replace rear base cover.
40 Reattach monitor. WARNING
Impact Hazard!
Moving Parts can Crush and Cut.
Raise monitor to top of vertical
adjustment BEFORE removing.
Failure to heed this warning may result in
serious personal injury or property damage!
822-310