ESBE DxA100 Series User manual

87/6/0,6
0
5
15
Psi/bar/Mpa
+122 +50
ESBE System Units
SERIES DxA100
Series DDA111 Series DAA111
ESBE AB
Bruksgatan 22
SE‒333 75 Reftele
www.esbe.eu
LVD 2014/35/EU
EMC 2014/30/EU
RoHS 2011/65/EU
ErP 2009/125/EU
PED 2014/68/EU, article 4.3
EnEV 2014
SI 2016 No. 1101
SI 2016 No. 1091
SI 2012 No. 3032
SI 2010 No. 2617
SI 2016 No. 1105
Mtrl.nr. 98141116• Ritn.nr. 7946 vers. A • Vers. 2023‒03‒29
SERIES FUNCTION
DAA111
DDA111
180
60
302
270
90
270
20
180º
>
180º
>
0º
»
1
1
2Remove insulationRemove actuatorDimensions Mounting position

»Click
40 - 50 Nm
c/c 90mm
1
2
2
180mm
1
5
3
282
4
6 7
Mount the cables
Wall mounting Connecting the pipes Mount the insulation
Cabling Assemble actuator
OUICK FIT!
Click!

SERIES ARA600 Prop
Pro
P
SERIES ARA600 3-Point
S
ERIE
S
ARA
60
SERIES ARA600 2-Point
2
CCWNCW
bkbu bn
L(bn)
N(bu)
PE (gn)
Electric installation
0
20 MINUTES
Commissioning
Flow
Filling and
venting
Open
White mark, indicate
check valve position
45
o
Filling and venting
Preparation
Open Closed
90
o
Checkvalve position
Flow
OPEN
AIR
CLOSE
Assemble removed knob
http://www.esbe.eu/global/
en/products/rotary-valves
∅10 mm
6 =
6 =
9By-pass ON/OFF
By-pass closed
By-pass open

Application
information
Wilo
Variable differential
pressure - Δp-v
Constant differential
pressure - Δp-c
Constant speed
PUMP CURVE
I, II, III
CONTROL MODE
NORMAL
OPERATION FAULT
NORMAL
OPERATION
FAULT
CONTROL MODE
Variable differential
pressure - Δp-v
Constant differential
pressure - Δp-c
Constant speed
PUMP CURVE
I, II, III
Wilo Display
http://www.esbe.eu/global/en/
products/circulation units
WILO - Faults, Causes and
Remedies
LED displayclick Control mode Pump curve
Recomended
Alt.
1Constant speed II
Constant speed I
Variable differential III
Variable differential II
I
III
6
II
I
III
2
3
4
5
7
8
9
Click
Click
Recommended Alternative
LED display Control mode Pump curve
Constant speed
Constant speed
Variable differential
pressure Δp-v
Variable differential
pressure Δp-v
Variable differential
pressure Δp-v
Constant differential
pressure Δp-v
Constant differential
pressure Δp-v
Constant differential
pressure Δp-v
Constant speed
Settings navigationsPump Settings 10
Expose application info using leaflet
11
= Factory settings
Factory setting
GXX X00
Nameplate
Factory
setting
+
Hold
8 sec 1 sec
1 sec
30 sec
10 min
Hold
LED display Status
Locked
Unlocked
Venting
Factory
setting
Hold
8 sec
Hold
8 sec
Hold
8 sec
1. Hold 2. 3. 4.
Manual
restart
LED Faults Cause Remedy
Lights up
red Blocking Rotor blocked Activate manual
restart or contact
customer service
Contacting/ winding Winding defective
Flashes
red Under/overvoltage Power supply too low/high on mains
side
Check mains voltage
and operating con-
ditions, and request
customer service
Excessive
module temperature Module interiour too warm
Short-circuit Motor current too high
Flashes
red/
green
Generator operation
Water is flowing through the pump
hydraulics, but there is no mains vol-
tage at the pump
Check the mains
voltage, water
quantity/pressure
and the ambient
conditions
Dry run Air in the pump
Overload
Sluggish motor, pump is operated
outside of its specifications (e.g. high
module temperature). The speed is
lower than during normal operation