ZKTeco SF1008+ User manual

Quick Start Guide
SF1008+
Version: 1.0
Date: April 2020

1
1Overview
8-inch touchscreen
Camera & palm collector
Speaker
Reset button
Flash
Exit
button
Auxiliary
input
AUX
AL+
AL-
NC
COM
NO
BUT
GND
SEN
GND
Alarm
Lock
Sensor
GND
+12V Power
GND
INWD0
INWD1
Wiegand
In
Wiegand
Out
12V
GND
WD0
WD1
Networkinterface
RS232
RS485
12V
485B
485A
GND
TXD1
RXD1
GND
GND
GND
12V
12V
Power
interface
Tamper switch
Near-infrared flash
Thermal infrared temperature
measurement module
Microphone (Optional)

2
①
②
3
3 Device Installation
①Attach the mounting template sticker to the wall, and drill holes according to the mounting
paper.
②Fix the back plate on the wall using wall mounting screws.
③Attach the device to the back plate.
④Fasten the device to the back plate with a security screw.
Install on the wall
1 2
4
1.5m
INDOOR USE
Please refer to the following recommendations for installation.
AVOID DIRECT
SUNLIGHT
AND EXPOSURE
KEEP DISTANCE AVOID GLASS
REFRACTION
KEEP EFFECTIVE
DISTANCE
20-50cm
10ft
6.5ft
window
2 Installation Environment

Install on the barrier gate
Please thread the wire through the bracket before installation.
①Drill a hole on the barrier gate, insert the bracket into the hole and fix it with a nut.
②Adjust the angle of the device.
3
3 Device Installation
1
2
①
②

4
4 Standalone Installation
Alarm Smoke
detector
Lock TCP/IP
Exit button
Door sensor
Reader
PC
5 Door Sensor, Exit Button & Alarm Connection
Door sensor
Alarm power
Alarm
-
+
-+
-+
-+
Detector power
Smokedetector
Exitbutton
AUX
AL+
AL-
NC
COM
NO
BUT
GND
SEN
GND
GND

5
6 Lock Relay Connection
The system supports Normally Opened Lock and Normally Closed Lock.
The NO LOCK (normally unlocked when power-on) is connected with 'NO' and 'COM' terminals, and
the NC LOCK (normally locked when power-on) is connected with 'NC' and 'COM' terminals.
Take NC Lock as an example below:
1)Device not sharing power with the lock
Normally Closed Lock
DC12V
DC12V
2)Device sharing power with the lock
+12V
GND
FR107
FR107
Normally Closed Lock
GND
AUX
GND
SEN
GND
BUT
NO
COM
NC
AL-
AL+
DC12V
+12V
GND
GND
AUX
GND
SEN
GND
BUT
NO
COM
NC
AL-
AL+
7 Wiegand Reader Connection
Access controller
+12V
GND
Wiegand reader
INWD0
INWD1
12V
GND
WD0
WD1
Maximum DC12V input.

6
8 Barrier Connection
9 RS485 Connection
Barrier gate
+12V
GND
GND
485+
485-
12V
485B
485A
GND
TXD1
RXD1
GND
GND
GND
12V
12V
485 reader
12V
485B
485A
GND
TXD1
RXD1
GND
GND
GND
12V
12V
Note: 485A and 485B can be connected to the barrier gate or the 485 reader, but cannot be
connected to the gate and the reader at the same time.

11 Ethernet Connection
Connect the device and computer software over an Ethernet cable. An example is shown below:
: 192.168.1.201Default IP address
: 255.255.255.0 Subnet mask
: 192.168.1.130IP address
: 255.255.255.0 Subnet mask
Note: In LAN, IP addresses of the server (PC) and the device must be in the same network segment
when connecting to ZKBioAccess EP software.
Click on [Comm.] > [Ethernet] > [IP Address], input the IP address and click on [OK].
10 Power Connection
12V3ADC
Recommended power supply: 12V - 3A
To share the power with other devices, use a power supply with higher current ratings.
7
ZKBioAccessEP

12 UserRegistration
8
Method1: Register on the device
Clickon> [User Mgt.] > [New User] to register a new user. Settings include entering user ID and
name, registering palm, face, password and user photo, setting user role and access control role.
When there is no super administrator set in the device, click on to enter the menu. After setting the
super administrator, the system will request for the administrator’s verification before entering the menu.
For the security purpose, it is recommended to register a super administrator at the first time you use
the device.
LL
L
Enroll Palm

9
Method 2: Register on ZKBioAccess EP software
Please set the IP address and cloud service server address on the device.
2. Click [Personnel] > [Person] > [New] to register users in the software.
3. Add users to access levels.
4. Click [Access] > [Device] > [Device Control] > [Synchronize All Data to Devices].
For more details, please refer to the ZKBioAccess EP User Manual.
1. Click [Access] > [Access Device] > [Device] > [Search Device] to add the device to the software.
When the device has set the server address and port, it can be added automatically.
Step1
Step2
Step3
Step4

10
Method 3: Register on the phone
2. The users will display in [Personnel] > [Temporary Personnel], click [Review].
Once ZKBioAccess EP software installed, users could enroll face via browser application on their own
mobile phone.
1. Click [Personnel] > [Parameters], input ‘’http://Server address:Port’’ in the QR Code UGL bar. The
software will automatically generates a QR code. Scan the QR code or login onto ‘’http://Server
address:Port/app/v1/adreg’’ by the mobile phone to register users.
Personnel Registration
Personnel Registration
Personnel ID
First Name
Last Name
Last Name
Mike
4835

Clickon > [Comm.] > [Ethernet]to set the network parameters. If the TCP/IP communication of the
device is successful, the icon will be displayed in the upper right corner of the standby interface.
Clickon that is, the IP > [Comm.] > [Cloud Server Setting] to set the server address and server port,
address and port number of the server after the software is installed. If the device communicates with
the server successfully, the icon will be displayed in the upper right corner of the standby interface.
14 Ethernet and Cloud Server Settings
13 Access Control Settings
Clickon to enter the access control management interface and set relevant > [Access Control]
parameters of access control.
L
L
11

12
15 Detection Management Settings
L
Click on enter the management interface > [System] > [Detection Management]to detection . You
can set the value of High temperature alarm threshold. The device will send an alarm prompt when
the temperature of the user detected exceeds this value. When the Temperature over the range;
access denied is enabled, the user will be forbidden to access, as shown in the following figure.
Temperature over the range; access denied
Deny access without mask
Enable mask detection
Temp. Unit
Temperature deviation correction
Low temperature alarm threshold
High temperature alarm threshold
Enable temperature screening with infrared
Detection Management
08:50
Normal temperature
Measure Temp.
O
Temp.: 36.65 C
Mask Detected
Successfully verified
Name:Mike
User ID:4835
Verify:Face
08:50
Measure Temp.
Successfully verified
Name:Mike
User ID:4835
Verify:Face
Temperature over the range
O
Temp.: 37.65 C
Without mask
L

13
1. The effective distance for temperature detection is within 50cm.
2. Recommended for indoor use.
3. Temperature measurement data is for reference only, not for medical use.
4. Remove the mask to register the face, wear a mask to recognize the face, the type of mask, the size of
the face covered by the mask, and bangs will affect the facial recognition effect.
5. Facial verification for masked individuals will increase FAR. Palm verification for masked individuals is
recommended.
Note:
Once ZKBioAccess EP software installed, users could perform epidemic management on browser.
Real-time monitoring on ZKBioAccess EP software
Please set the IP address and cloud service server address on the device and add the device to the
software.
1. Click [Prevention] > [Epidemic] > [Real-time monitoring] to view all the events include the user whose
temperature is over the range. When the Alarm temperature setting has set, the abnormal body
temperature will be marked red automatically.
1. Click [Prevention] > [Epidemic] > [Real-time monitoring] to view all the events include the user whose
temperature is over the range. When the Alarm temperature setting has set, the abnormal body
temperature will be marked red automatically.
2. Click [Epidemic] > [Statistics panel] to view the analysis of statistical data and view the personnels with
normal temperature.
As shown in the following figure.
Effective distance
Effective distance:
Temperature: 20-50cm
Face & Palm: 20-50cm

14
For more details, please refer to the ZKBioAccess EP User Manual.

16 Method for Enrolling Palm
15
20-50cm
1. Place your palm within 20-50cm of the device.
2. Place your palm in the palm collection area, such that the palm is placed parallel to the device.
3. Make sure to keep space between your fingers.
Note:

1600 Union Hill Road Alpharetta, GA 30005
Phone: [phone]
www.zktecousa.com
Copyright©2020 ZKTeco USA LLC. All rights reserved.