ETC Echoflex ELED1H User manual

Page 1ELED1H Installaon Guide
Installaon Guide
ELED1H Fixture Controller
IMPORTANT SAFEGUARDS
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
• CAUTION - This equipment has more than
one power supply connection point. To reduce the
risk of electric shock disconnect both the branch
circuit-breakers or fuses and emergency power
supplies before servicing.
• CAUTION – Risk of Electric shock hazard. The
controller uses high voltage and should only be in-
stalled by qualied personnel in accordance with
National Electrical Code and any local regulations.
• CAUTION - To avoid electrical overload, total
connected load should not exceed output rating.
• This product is suitable for use in dry locations
where the ambient temperature is -5°C to +50°C.
• Do not use outdoors.
• Do not mount near gas or electric heaters
• Equipment should be mounted in locations
and at heights where it will not be subjected to
SAVE
THESE INSTRUCTIONS

Page 2 ELED1H Installaon Guide
tampering by unauthorized personnel.
• The use of accessory equipment not
recommended by the manufacturer may cause an
unsafe condition.
• Do not use this equipment for other than its in-
tended use.
• Servicing should be performed by qualied ser-
vice personnel.
• Pollution Degree:2.

Page 3ELED1H Installaon Guide
Overview
This guide covers the LED Fixture Controller, model number ELED1H-AU with
input voltage of 240-347VAC. The ELED1H is equipped with a 902 MHz
radio. The box contents includes the controller and installation guide.
A programming guide with detailed features of the controller is available for
download on www.echoexsolutions.com.
The controller uses wireless technology to monitor any room’s environment
and provides dimming and/or switching control of an LED xture.
The controller includes Simple Tap™ technology which allows installers and
facility operators to manage conguration settings without any tools.
Preparing To Install The Controller
The controller should be mounted in locations and at heights where it will
not be subjected to tampering by unauthorized personnel. The controller is
mounted using the conduit nipple for mounting the controller to electrical
junction boxes or panels. You will require hand tools and supplies (not
provided) to install the controller.
• Screwdrivers, pliers, wire cutters, wire insulation stripping tool
• Appropriately sized wire nuts
• Small cable ties
Scan QR code for link to programming guide

Page 4 ELED1H Installaon Guide
Installing the Controller
For best results mount the controller on the outside of the electrical box either
directly at the electrical load or before the load in the circuit.
Review these instructions completely before installing the controller.
1. Locate the circuit breaker panel and terminate power to the circuit.
2. Remove all face plates and other hardware from the junction box so
you can access the high voltage wires.
3. Mount the controller to the exterior of the junction box or panel with
the ½” threaded nipple.
4. Refer to the wiring diagram to connect the controller to line power,
neutral and load wires. Use wire nuts on all connections and
individually cap any bare wires (except orange antenna wire).
5. Connect the gray and purple wires to the driver or ballast’s dimming
interface (optional).
6. Replace the electrical box faceplate.
7. Restore power to the circuit.
8. If the controller was pre-commissioned you can use one of the pre-
linked devices to test the controller operation. If the controller was not
pre-commissioned by the factory, refer to the section of this guide
titled Linking the First Switch. Use this switch to verify the controller
functionality.
Wiring Diagram
ELED1H-AU
LED Fixture Controller
Power
LED
Clear
Button
Learn
Button
Learn
LED
Max. Switching Load
20A@240 -277VAC,
Electronic Ballast or LED Driver
16A@347VAC,
Electronic Ballast or LED Driver
Max. Dimming Load
100 mA sinking
Antenna (orange)
Do not cut or cap
Black - Line, 240-347VAC
@50/60 Hz
500 mW max
White - Neutral
Red - Load, 240-347VAC
Purple - Dimming 0-10V
Gray - Dimming COM
LED Driver
Max. Impulse Voltage: 4000V
Internal Relay: Type 1.C
Dimming output is Class 1 circuit
Independently Mounted Control for
Panel Mount/Surface Mount
iNote: Always follow applicable NEC and local electrical code
requirements when installing and powering the controller.
iNote: The Micro USB port is for factory use only. Do not attach
cables or accessories to this port
The use of accessory equipment not recommended by the manufacturer
may cause an unsafe condition. Do not use this equipment for other than
its intended use. Do not use outdoors.

Page 5ELED1H Installaon Guide
Electrical Terminations
The controller has an external orange antenna wire. Do not cut, cap or
connect this wire.
Power to the controller is connected between the White (Neutral) and the
Black (240-347 VAC) Line power. The Class 1 power limited dimming lines
(violet and gray wires) can be used to provide 0-10V control of a dimming
ballast or LED driver. Use only UL approved wire when making connections
to the controller, see table below.
Controller's Wire Details
Connection Color Specification
Load Red 14AWG, 600V
Neutral White 14AWG 600V
Line 240-347VAC Black 14AWG 600V
Dimming 0-10V Purple 18AWG 600V
Dimming GND Gray 18AWG 600V
Wiring Diagrams - For Use in Emergency Fixtures
ELED1H-AU
LED Fixture Controller
Power
LED
Clear
Button
Learn
Button
Learn
LED
ELED1H-AU
LED Fixture Controller
Power
LED
Clear
Button
Learn
Button
Learn
LED
Normal Hot
Normal Neutral
Emergency Hot
Emergency Neutral
Normal Control Sense
Normal/
Emergency
Load
ELED1H
Load Control
Dimming +Dimming -
LED Driver Hot
LED Driver Neutral
LED Driver
UL924 Emergency
Bypass Relay
with appropriate
voltage rang
Normal Hot
Normal Neutral
LED Driver
LED
Emmier
Board
Baery
Backup
Dimming +Dimming -
LED +LED -
LED +
LED -
ELED1H
Load Control
LED Driver
Hot

Page 6 ELED1H Installaon Guide
Linking the First Switch
Use this method to link the rst switch. Use the learn button to link additional
devices.
1. If the controller already has a sensor linked, press the TEACH button on
the linked sensor and proceed to step 2 within 60 seconds.
2. Click the wireless switch paddle ON three times, OFF three times and
ON three times sequentially within 5 seconds. The relay will toggle and
the red POWER LED will begin a repeating blinking pattern to indicate
the linked switch, see the section on LED blink codes.
LEARN button
The LEARN button is used to link switches or sensors to the controller.
1. Press the button marked LEARN for a half second. In link mode the
LEARN LED will stay ON and the POWER LED will toggle every two
seconds.
2. When linking a wall switch, press the switch paddle ON three times.
If linking a sensor, press the sensor’s TEACH or LINK button, refer to
the sensor’s documentation. The POWER LED will remain lit for four
seconds while it links the new device. It will resume toggling allowing
you to link another device up to a total of twenty devices.
3. To exit link mode, press and release the LEARN button on the controller.
iNote:Linking a switch or sensor that is already linked to a controller,
will remove or unlink it from the controller.
iNote: Link mode will time out after no activity in thirty seconds.
CLEAR button
Using the CLEAR button can reload the controller to the factory pre-
commissioned settings with linked devices OR it can load the factory default
parameters and remove all linked devices.
• To return the controller to the factory pre-commissioned state, press
the CLEAR button until the POWER and LEARN LEDs start blinking,
approximately 5 seconds. Release the button and the POWER LED will
begin blinking indicating the factory commissioned pre-linked devices.
• To completely clear the controller returning it to factory default settings
removing all linked devices, press the CLEAR button until the POWER
and LEARN LEDs come on solid, about 15 seconds, then release. The
POWER LED will stay ON solid indicating the factory default state.

Page 7ELED1H Installaon Guide
LED Blink Codes and Operation
The tables below describe the LED activity and associated mode of the
controller.
If the controller was factory pre-commissioned, upon power up it will
immediately begin blinking the red POWER LED based on the type and count
of linked devices. The type is indicated by long blinks followed by short blinks
counting the number of devices linked. This pattern will repeat after a short
pause.
The table below describes the number of LED blinks for each device type.
POWER LED Blink Codes
Factory Default ON Solid
switch(es) 1 long blink followed by short blinks counting switches
occupancy sensor(s) 2 long blinks followed by short blinks counting sensors
photo sensor(s) 3 long blinks followed by short blinks counting sensor
(typical max 1)
central command 4 long blinks followed by short blinks counting devices
demand response 5 long blinks followed by short blinks counting devices
Operang Mode and LED Acvity
Mode Red LEARN LED Red POWER LED Relay/Light
link mode ON toggle toggle
storing ID ON ON 4 seconds ON 4 seconds
clearing ID ON OFF 4 seconds OFF 4 seconds
factory default ON 1 second ON solid ON

Page 8 ELED1H Installaon Guide
Lisngs & Regulatory Statements
UL Listed Component
Certied UL Standard 924
Certied UL Standard 60730
Certied CAN/CSA Std E60730
UL 2043 Plenum rated
California Energy Commission Title 24 - CEC
Washington State Energy Code - WSEC
ANSI / ASHRAE / IES Standard 90.1
International Energy Conservation Code - IECC
New York City Energy Conservation Code - NYCECC
FCC Part 15.231 Contains FCC ID: SZV-STM300U
IC RSS-210FCC Part 15.231 Contains FCC ID: SZV-STM300U
The enclosed device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(i.) this device may not cause harmful interference and
(ii.) this device must accept any interference received, including
interference that may cause undesired operation.
Echoflex Solutions
38924 Queens Way, Unit #1, Squamish, BC, V8B 0K8, Canada n+1 778-733-0111
echoflexsolutions.com n8DC-5973-1.0 nDocument Part # 8189M21-5973-1 Rev A n12/20
Copyright © 2020 Echoflex Solutions, Inc.
Product information and specications subject to change without notice