Eterna FL124B User manual

Issue 2013
Model:
FL124B
23W Low Energy Floodlight
These instructions are provided as a guideline to assist you.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION
AND RETAIN FOR FUTURE REFERENCE
Pack contents:
1 x Fitting
1 x 23W ES CFL lamp
FOR PRODUCT ADVICE:
• T: 01933 673 144
• F: 01933 678 083
• E: [email protected].uk
Visit our website:
www.eterna-lighting.co.uk
INSTALLATION INSTRUCTIONS
A guide for qualied electricians
874/2012
A
MODELNO.
FL124B
MODELNO.
A++
XXX kWh/1000h
22.50
CFL23W
A
EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Directive” eective August 2005—UK
WEEE Regulations eective 2nd January 2007).
Environment Agency Registered Producer: WEE/
GA0248QZ.
WHEN YOUR PRODUCT COMES TO THE END OF
ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE
RECYCLE IT WHERE FACILITIES EXIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.
CLEANING:
Disconnect the power and clean the exterior only of
this tting with a moist (not wet) cloth.
Do not use any chemical or abrasive cleaners.
IF YOU EXPERIENCE PROBLEMS:
If you believe your product is defective, please return
it to the place where you bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, but may not be able to give specic
instructions regarding individual installations.
For breakage information visit:
www.eterna-lighting.co.uk
LAMP SPECIFICATIONS:
Voltage 220-240V
Frequency 50Hz
Nominal lumens 1371 lm
Wattage 23W
Nominal life time of the lamp 10,000 hrs
Number of switching cycles
before premature lamp
failure
30,000
Colour temperature 6400K
Warm-up time up to 60 % of
the full light output 40s
Dimmable No
Lamp dimensions (mm) 140 x 59
Lamp mercury content to an
accuracy of 0.1mg 2.5
Cap type ES (E27)
Rated Wattage 22.5W
Rated luminous ux 1371 lm
Rated lamp lifetime 10,000
Colour rendering index Ra 80%
Lamp power factor 0.55
Lumen maintenance factor at
end of nominal life 50%
Starting time 0.9s

READ THIS FIRST:
Check the pack and make sure you have all of the
parts listed on the front of this booklet. If not,
contact the outlet where you bought this product.
This product contains glass, care must be taken when
assembling, tting or handling to prevent personal
injury or damage to the product.
This light tting must be installed by a competent
person in accordance with the Building Regulations
making reference to the current edition of the
IEE Wiring Regulations (BS7671). The Building
Regulations may be obtained from HMSO or viewed
and downloaded from www.communities.gov.uk
following the link for Building Regulations.
As the buyer, installer and/or user of this product it
is your own responsibility to ensure that this tting
is t for the purpose for which you have intended
it. Eterna Lighting cannot accept any liability for
loss, damage or premature failure resulting from
inappropriate use.
The lamps (bulbs/tubes) supplied with this tting are
consumable parts and therefore may be outside of
any warranty oered.
Switch o the mains before commencing installation
and remove the appropriate circuit fuse.
When working at heights, please use a suitable
platform.
Disconnect the tting from the electrical supply
before ash or high voltage testing.
Suitable for indoor and outdoor use.
This product is suitable for installation on surfaces
with normal ammability e.g. wood, plasterboard,
and masonry. It is not suitable for use on highly
ammable surfaces (e.g. polystyrene, textiles).
Before making xing hole(s), check that there are no
obstructions hidden beneath the mounting surface
such as pipes or cables.
The chosen location of your new tting should allow
for the product to be securely mounted and safely
connected to the mains supply (lighting circuit).
When choosing the location for your new tting,
ensure that the xings will be anchored in a solid
surface e.g. concrete, brick or a joist—do not x
directly onto panelling, cladding, plasterboard etc.
If the location of your new tting requires the
provision of a new electrical supply, the supply
must conform with the requirements of the Building
Regulations making reference to the current edition
of the IEE Wiring Regulations (BS7671).
This product is designed for permanent connection
to xed wiring: this should be either a suitable
lighting circuit (protected with a 5 or 6 Amp MCB or
fuse) or a fused spur (with a 3 Amp fuse) via a fused
connection unit.
We recommend that the supply incorporates a
switch for ease of operation.
Make connections to the electrical supply in
accordance with the following code:
Live - Brown or Red
Neutral - Blue or Black
Earth - Green and Yellow
When making connections, ensure that the terminals
are tightened securely and that no strands of wire
protrude. Check that the terminals are tightened
onto the bared conductors and not onto any
insulation.
This product must be connected to Earth.
IMPORTANT: Always switch o at the mains before
changing the lamp.
You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out:
these tests are specied in the Wiring Regulations
(BS7671) referred to in the Building Regulations.
INSTALLATION:
01. Choose the location for your new oodlight
giving consideration to all of the conditions listed
above.
02. Using the xing strap as a template, mark the
position for the xing holes on your mounting
surface.
03. Prepare your mounting surface as appropriate for
your chosen xings (not supplied). Use a spirit
level to ensure the tting will be level.
04. Secure the tting in place.
05. Loosen the bolts at each end of the xing strap
and adjust the angle of your oodlight to give the
desired spread of light.
06. Tighten the bolts to lock your oodlight in
position.
07. Make the connections to your mains supply as
described in the “Read this rst” section.
08. Using a cross-headed screwdriver, undo the
screws that secure the diuser and allow to hang
down.
09. Fit the uorescent lamp.
10. Replace the diuser and tighten the screws
making sure that the waterproof gasket is
correctly positioned and compressed.
11. Press the trim back onto the front of the tting
making sure the slots used for removal are at the
bottom.
12. Restore the power and switch on.
LAMP REPLACEMENT:
01. Switch o the electricity at the mains.
02. Using a cross-headed screwdriver, undo the
screws that secure the diuser and allow to hang
down.
03. Remove the lamp.
04. Insert new lamp.
05. Replace the diuser and secure in position
making sure that the gasket is correctly
positioned and compressed.
06. Restore the power and switch on.
REPLACEMENT LAMP TYPE:
Fitting requires 1 x 23W ES helical CFLi 6400K
(included) or energy saving alternative.
Fitting is rated at 23W max.