EtherWAN ED3331 User manual

10/100Base-TX Industrial Ethernet Extender
1 V2
This quick start guide describes how to install and use the Ethernet Extender. The Ethernet Extender introduced
here provides one channel for Ethernet over existing coaxial cable.
Product Overview
Use DIN-Rail Mounting Kit:
Fit the DIN-Rail mounting kit onto the bottom of the unit and fasten the
screws. The Ethernet Extender can use DIN-Rail mounting kit to fix on
the DIN-Rail.
Product Features
yComplies with EN61000-6-2 & EN61000-6-3 EMC Generic standard immunity for Industrial environment.
yOperates transparent to higher layer protocols.
yOne Ethernet port (RJ-45 connector): 10/100Mbps-Full/Half-duplex, Auto-negotiation, Auto-MDI/MDIX.
yComplies with IEEE802.3 10Base-T and IEEE802.3u 100Base-TX standards.
yOne Ethernet Extender port (BNC connector): Symmetrical on the VDSL, high-speed Full-duplex 85Mbps
communications link over existing coaxial cable.
yProvides BNC to F-Type connector.
ySupports one DIP switch to select local or remote side.
yTen reference speeds supports up to 85Mbps @ about 200 meters (656ft.), down to 1Mbps @ about 2,600 meters
(8,530ft.).
yExternal AC to DC power adapter.
y-10℃to 60℃(14℉to 140℉) operating temperature range.
yHardened aluminum case.
ySupports DIN-Rail or Wall Mounting installation.
yUsed as a stand-alone device or with a chassis.
yHot-swappable when used with a chassis.
Ethernet Extender Mode Settings
Ethernet Extender mode settings are made very simple by means of a switch at the rear panel of the Ethernet
Extender. The switch has two positions for Ethernet Extender mode settings. Refer to the table below for more
details. One device must be set to Loc and the other to Rmt when two devices are connected.
Loc Rmt
The device operates in local mode The device operates in remote mode

10/100Base-TX Industrial Ethernet Extender
2 V2
Connecting to Power
This Ethernet Extender is a plug-and-play device. Connect the supplied AC to DC power adaptor to the receptacle
on the rear panel of the Ethernet Extender, and then attach the plug into a standard AC outlet.
Front Panel & LEDs
The LED indicators give you instant feedback on status of the Ethernet Extender:
LEDs State Indication
Steady Power on, Pwr stands for POWER
Pwr Off Power off
Ethernet
Steady A valid Ethernet connection established, Lnk stands for LINK
Flashing Transmitting or receiving Ethernet data, Act stands for ACTIVITY
Lnk/Act
Off Neither valid Ethernet connection established nor transmitting/receiving Ethernet data
Steady Ethernet Connection transferring at 100Mbps
100 Off Ethernet Connection transferring at 10Mbps
Ethernet Extender
Green Link Speed: 1~5Mbps, Distance: 2,600 meters (8,530ft.)
1 Amber Link Speed: 6~10Mbps, Distance: 2,400 meters (7,874ft.)
Green Link Speed: 11~16Mbps, Distance: 2,000 meters (6,561ft.)
2 Amber Link Speed: 17~20Mbps, Distance: 1,800 meters (5,905ft.)
Green Link Speed: 21~29Mbps, Distance: 1,600 meters (5,249ft.)
3 Amber Link Speed: 30~43Mbps, Distance: 1,400 meters (4,593ft.)
Green Link Speed: 44~54Mbps, Distance: 1,200 meters (3,937ft.)
4 Amber Link Speed: 55~63Mbps, Distance: 1,000 meters (3,280ft.)
Green Link Speed: 64~74Mbps, Distance: 600 meters (1,968ft.)
5 Amber Link Speed: 75~85Mbps, Distance: 200 meters (656ft.)
Rmt Steady The device operates in remote mode
Loc Steady The device operates in local mode
Err Steady Error occurred
Lnk Steady A valid connection established
Self-diagnostic Test Procedure
yTwo Industrial Ethernet Extenders are connected in pairs by BNC connectors over coaxial cable.
yOne Industrial Ethernet Extender is configured as local unit located at local site of Ethernet extension by setting
mode switch at rear panel of this Industrial Ethernet Extender to Loc (local mode).
yThe other Industrial Ethernet Extender is configured as remote unit located at remote site of Ethernet extension by
setting mode switch at rear panel of this Industrial Ethernet Extender to Rmt (remote mode).
yConnect suppliedAC to DC power adaptors to receptacle on rear panel of these two Industrial Ethernet Extenders
and then attach plugs into standardAC outlet sockets to power on these two Industrial Ethernet Extenders.
yLED 5 on top panel of these two Industrial Ethernet Extenders might light on in amber or green color if these two
Industrial Ethernet Extenders are connected in pairs by BNC connectors over a short coaxial cable (less than 200
meters). This means that these two Industrial Ethernet Extenders could operate in normal condition since they
finally negotiate a best performance for symmetrical transmission.