EtherWAN EX42000 Series User manual

EX42000 series Industrial Ethernet Switch / Media Converter www.etherwan.com
This quick start guide describes how to install and use the Industrial Ethernet Switch /
Media Converter. Capable of operating at temperature extremes of -10°C to +60°C,
this is the Switch / Media Converter of choice for harsh environments constrained by
space.
The Terminal Block and Power Input
Physical Description
The Port Status LEDs
LED State Indication
10/100TX or 100FX/BX
Steady A valid network connection established.
LINK stands for LINK.
LINK/ACT Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
Steady The port is transferring at 100Mbps.
100 Off The port is transferring at 10Mbps If this LED is dark.
The Terminal Block
PWR Power Input
GND Power Ground
Earth Ground
DC Terminal Block Power Input: The DC Terminal Block power input can be used to
power up this Switch / Media Converter.
CAUTION: This equipment is designed to permit the connection of the earthed
conductor of the DC supply circuit to the earthing conductor at the equipment.
If this connection is made, all of the following conditions must be met:
This equipment shall be connected to directly to the DC supply system earthing
electrode conductor or to a bonding jumper from an earthing terminal bar or bus to
which the DC supply system earthing electrode conductor is connected.
This equipment shall be located in the same immediate area (such as, adjacent
cabinets) as any other equipment that has a connection between the earthed
conductor of the same DC supply circuit and the earthing conductor, and also the
point of earthing of the DC system. The DC system shall not be earthed
elsewhere.
The DC supply source is to be located within the same premises as the
equipment.
Switching or disconnecting devices shall not be in the earthed circuit conductor
between the DC source and the point of connection of the earthing electrode
conductor.
1
70G-EX42000Q5

EX42000 series Industrial Ethernet Switch / Media Converter www.etherwan.com
2 70G-EX42000Q5
The 10/100Base-TX and 100Base-FX/BX Connectors
The 10/100Base-TX Connections
The following lists the pinouts of 10/100Base-TX ports.
Pin Regular Ports Uplink port
1 Output Transmit Data + Input Receive Data +
2 Output Transmit Data - Input Receive Data -
3 Input Receive Data + Output Transmit Data +
4 NC NC
5 NC NC
6 Input Receive Data - Output Transmit Data -
7 NC NC
8 NC NC
The 100Base-FX Connections
The fiber port pinouts
The Tx (transmit) port of device I is connected to the Rx (receive)
port of device II, and the Rx (receive) port of device I to the Tx
(transmit) port of device II.
The WDM 100Base-BX Connections
The fiber port pinouts
Only one Single mode or Multi mode optical fiber is required to
transmit and receive data.
Functional Description
Complies with EN61000-6-2 & EN61000-6-4 EMC Generic standard immunity for
industrial environment.
Supports IEEE802.3az 10Base-Te only. 10Base-T is not supported. 10Base-Te is
fully interoperable with 10Base-T over 100m of class D (Category 5) or better
cabling as specified in ISO/IEC 11801:1995.
Supports 802.3az/802.3u/802.3x. Auto-negotiation: 10/100Mbps, Full/Half-duplex.
Auto MDI/MDIX.
100Base-FX: Multi mode SC or ST type, Single mode SC or ST type.
100Base-BX: WDM Multi mode or Single mode SC type.
Supports 1024 MAC addresses, 448K bits buffer memory.
IEEE802.3x Flow control for Full-duplex, Back pressure for Half-duplex.
None-blocking architecture and full wire-speed forwarding rate.
Supports IEEE802.1p QoS with two priority queues.
Supports IEEE802.3az Energy Efficient Ethernet (EEE).
Supports Max. length of frame up to 1552 Bytes.
Power consumption: 2.12W Max.
Power Supply: DC Terminal Block power input, 12-48VDC.
Operating temperature ranges from -10°C to 60°C (14°F to 140°F).
Plastic compact DIN-Rail industrial case design.
Assembly, Startup, and Dismantling
Assembly: Place the device on the DIN rail from above using the slot. Push the
front of the device toward the mounting surface until it audibly snaps into place.
Startup: Connect the supply voltage to start up the device via the terminal block.
Dismantling: Pull out the lower edge and then remove the device from the DIN
rail.