EtherWAN EX45900 series User manual

EX45900 series www.etherwan.com
Quick Start Guide
This quick start guide describes how to install and use the
Hardened PoE Gigabit Ethernet Switch. Capable of operating
at temperature extremes of -40°C to +75°C, this is the switch
of choice for harsh environments constrained by space.
Physical Description
The Port Status LEDs
1

EX45900 series www.etherwan.com
LED State Indication
Steady Power on.
Power (Green) Off Power off.
Steady Relay starts alarm.
Fault (Red) Off Relay non-alarm.
Gigabit Ports
Steady A valid network connection established.
10/100Mbps: Green, 1000Mbps: Amber.
Blinking Transmitting or receiving data.
Act stands for Activity.
Link/Act
Off No link.
Steady Powered Device is connected.
Off Powered Device is disconnected.
PoE (Amber)
Blinking While Powered Device over 30W.
The Terminal Block and Power Inputs
Power Input Assignment
＋24/48VDC
Power1
－Power Ground
＋24/48VDC
Power2
－Power Ground
Earth Ground
Terminal Block
Relay Output Rating 1A @ 250VAC
DC Terminal Block Power Input: The DC Terminal Block
power input can be used to power up this Switch.
2

EX45900 series www.etherwan.com
DIP Switch Settings
On OffDIP No.
1 Port 1 Alarm Enable. 1 Alarm Disable.Port
2 Port 2 Alarm Enable. Port 2 Alarm Disable.
3 Port 3 Alarm Enable. Port 3 Alarm Disable.
4 Port 4 Alarm Enable. Port 4 Alarm Disable.
5 Port 5 Alarm Enable. Port 5 Alarm Disable.
6
(Only for EX45915) Port 6 Alarm Enable. Port 6 Alarm Disable.
7 Broadcast Storm Enable. le.Broadcast Storm Disab
8 Jumbo Frame Enable. Jumbo Frame Disable.
he 1000Base-TX (PoE) and Gigabit Ethernet
se-TX Connections Base-TX ports.
T
Connectors
1. The 1000Ba
The following lists the pinouts of 1000
3

EX45900 series www.etherwan.com
Pin Signal Name Signal Definition
1 TP0＋Transmit and Receive Data 0 ＋
2 TP0－Transmit and Receive Data 0 －
3 TP1＋Transmit and Receive Data 1 ＋
4 TP2＋Transmit and Receive Data 2 ＋
5 TP2－Transmit and Receive Data 2 －
6 TP1－Transmit and Receive Data 1 －
7 TP3＋Transmit and Receive Data 3 ＋
8 TP3－Transmit and Receive Data 3 －
2. The SFP Socket Connections
The SFP socket for Gigabit fiber optic expansion.
3. The 1000Base-SX/LX Connections
The fiber port pinouts: The Tx (transmit) port of device I is
connected to the Rx (receive) port of device II, and the Rx
(receive) port of device I to the Tx (transmit) port of device II.
4. The WDM 1000Base-BX Connections
The fiber port pinouts: Only one optical fiber is required to
transmit and receive data.
4

EX45900 series www.etherwan.com
Functional Description
Complies with EN61000-6-2 & EN61000-6-4 EMC
Generic standard immunity for industrial environment.
Supports 802.3/802.3u/802.3ab/802.3z/802.3x.
Auto-negotiation: 10/100/1000Mbps, Full/Half-duplex.
Auto MDI/MDIX.
1000Base-SX/LX: Multi mode SC or ST type, Single
mode SC type. 1000Base-BX: WDM Single mode SC
type.
Supports 8192 MAC addresses, 1M bits buffer memory.
Supports IEEE802.3az Energy Efficient Ethernet
(EEE).
High speed, non-blocking four traffic class QoS switch
fabric.
Supports Jumbo frame up to 10K Bytes.
Enable Broadcast Storm Protection by DIP Switch No.
7 to limit 15,000 packets per second.
Port 1~4 support IEEE802.3at Power over Ethernet
(PoE) Power Sourcing Equipment (PSE) and provide
power up to 30W.
Power consumption: 7W Max (Device only, without
PoE).
PoE power budget: 120W.
Power Supply: Redundant 24/48VDC Terminal Block
power inputs.
Operating temperature ranges from -40°C to 75°C
(-40°F to 167°F).
Slim design with DIN-Rail mount installation.
5

EX45900 series www.etherwan.com
Assembly, Startup, and Dismantling
Assembly: Place the switch on the DIN rail from above
using the slot. Push the front of the switch toward the
mounting surface until it audibly snaps into place.
Startup: Connect the supply voltage to start up the
switch via the terminal block.
Dismantling: Pull out the lower edge and then remove
the switch from the DIN rail.
6

EX45900 series www.etherwan.com
7
Preface
This manual describes how to install and use the Hardened
PoE Gigabit Ethernet Switch. This switch introduced here is
capable of operating at temperature extremes of -40°C to
+75°C, this is the switch of choice for harsh environments
constrained by space.
Port 1 to port 4 on this switch supports IEEE802.3at Power
over Ethernet (PoE) Power Sourcing Equipment (PSE) and
can detect an IEEE802.3at compliant Powered Device (PD).
Using external 48VDC power inputs through Terminal Block,
data and power can be transmitted to a Powered Device (PD)
over the same twisted-pair Ethernet cable through port 1 to
port 4 on the switch.
To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.
In this manual, you will find:
Features on the switch
Illustrative LED functions
Installation instructions
Specifications

EX45900 series www.etherwan.com
8
Table of Contents
QUICK START GUIDE 1
PHYSICAL DESCRIPTION 1
The Port Status LEDs 1
The Terminal Block and Power Inputs 2
DIP Switch Settings 3
The 1000Base-TX (PoE) and Gigabit Ethernet Connectors 3
FUNCTIONAL DESCRIPTION 5
ASSEMBLY,STARTUP,AND DISMANTLING 6
PREFACE 7
TABLE OF CONTENTS 8
PRODUCT OVERVIEW 9
HARDENED POEGIGABIT ETHERNET SWITCH 9
PACKAGE CONTENTS 9
PRODUCT HIGHLIGHTS 10
Basic Features 10
FRONT PANEL DISPLAY 11
PHYSICAL PORTS 12
INSTALLATION 13
SELECTING A SITE FOR THE SWITCH 13
DIN RAIL MOUNTING 14
CONNECTING TO POWER 15
DC Terminal Block Power Inputs 15
CONNECTING TO YOUR NETWORK 16
Cable Type & Length 16
Cabling 17
SPECIFICATIONS 18

EX45900 series www.etherwan.com
Product Overview
Hardened PoE Gigabit Ethernet Switch
Package Contents
When you unpack the product package, you shall find the
items listed below. Please inspect the contents, and report
any apparent damage or missing items immediately to your
authorized reseller.
This Switch
User’s Manual
9

EX45900 series www.etherwan.com
10
Product Highlights
Basic Features
Complies with EN61000-6-2 & EN61000-6-4 EMC
Generic standard immunity for industrial environment.
Supports 802.3/802.3u/802.3ab/802.3z/802.3x.
Auto-negotiation: 10/100/1000Mbps, Full/Half-duplex.
Auto MDI/MDIX.
1000Base-SX/LX: Multi mode SC or ST type, Single
mode SC type. 1000Base-BX: WDM Single mode SC
type.
Supports 8192 MAC addresses, 1M bits buffer memory.
Supports IEEE802.3az Energy Efficient Ethernet
(EEE).
High speed, non-blocking four traffic class QoS switch
fabric.
802.1Q VLAN Tag Based Priority, Class of Service.
Output Queue Schedule Mode: Weighted Round Robin
(WRR) with 4 priority queues.
The configurations of QoS are as below:
CoS Field Value Packet Count Priority
0 or 1 1 Lowest
2 or 3 2 Low
4 or 5 4 High
6 or 7 8 Highest
Supports Jumbo frame up to 10K Bytes.
Enable Broadcast Storm Protection by DIP Switch No.
7 to limit 15,000 packets per second.
Port 1~4 support IEEE802.3at Power over Ethernet
(PoE) Power Sourcing Equipment (PSE) and provide
power up to 30W.
Power consumption: 7W Max (Device only, without
PoE).
PoE power budget: 120W.

EX45900 series www.etherwan.com
Power Supply: Redundant 24/48VDC Terminal Block
power inputs.
Operating temperature ranges from -40°C to 75°C
(-40°F to 167°F).
Slim design with DIN-Rail mount installation.
Front Panel Display
 Power Status (PWR)
This LED comes on when the switch is properly connected to power and
turned on.
 Port Status LEDs
The LEDs display status for each respective port.
11

EX45900 series www.etherwan.com
LED State Indication
Steady Power on.
Power (Green) Off Power off.
Steady Relay starts alarm.
Fault (Red) Off Relay non-alarm.
Gigabit Ports
Steady A valid network connection established.
10/100Mbps: Green, 1000Mbps: Amber.
Blinking Transmitting or receiving data.
Act stands for Activity.
Link/Act
Off No link.
Steady Powered Device is connected.
Off Powered Device is disconnected.
PoE (Amber)
Blinking While Powered Device over 30W.
Physical Ports
This switch provides:
Five 10/100/1000Base-TX ports
Five 10/100/1000Base-TX ports + one
1000Base-SX/LX/BX port
Five 10/100/100Base-TX port + one Gigabit SFP slot
Connectivity
RJ-45 connectors on TX ports
ST or SC connector on 1000Base-SX/LX fiber port
SC connector on 1000Base-BX fiber port
Duplex LC connector on SFP 1000Base-SX/LX/BX
fiber transceiver
12

EX45900 series www.etherwan.com
13
Installation
This chapter gives step-by-step instructions about how to
install the switch:
Selecting a Site for the Switch
As with any electric device, you should place the switch
where it will not be subjected to extreme temperatures,
humidity, or electromagnetic interference. Specifically, the
site you select should meet the following requirements:
- The ambient temperature should be between -40 to 75
degrees Celsius.
- The relative humidity should be less than 95 percent,
non-condensing.
- Surrounding electrical devices should not exceed the
electromagnetic field (RFC) standards.
- Make sure that the switch receives adequate ventilation.
Do not block the ventilation holes on each side of the
switch
- The power outlet should be within 1.8 meters of the
switch.

EX45900 series www.etherwan.com
DIN Rail Mounting
Installation: Place the switch on the DIN rail from above using
the slot. Push the front of the switch toward the mounting
surface until it audibly snaps into place.
Removal: Pull out the lower edge and then remove the switch
from the DIN rail.
14

EX45900 series www.etherwan.com
Connecting to Power
DC Terminal Block Power Inputs
Step 1: Connect the DC power cord to the plug-able terminal block on the
switch, and then plug it into a standard DC outlet.
Step 2: Disconnect the power cord if you want to shut down the switch.
Power Input Assignment
＋24/48VDC
Power1
－Power Ground
＋24/48VDC
Power2
－Power Ground
Earth Ground
Terminal Block
Relay Output Rating 1A @ 250VAC
15

EX45900 series www.etherwan.com
16
Connecting to Your Network
Cable Type & Length
It is necessary to follow the cable specifications below
when connecting the switch to your network. Use
appropriate cables that meet your speed and cabling
requirements.
Cable Specifications
Speed Connector Port
Speed
Half/Full
Duplex
Cable Max.
Distance
10Base-T RJ-45 10/20 Mbps 2-pair
UTP/STP
Cat. 3, 4, 5
100 m
100Base-TX RJ-45 100/200
Mbps
2-pair
UTP/STP
Cat. 5
100 m
1000Base-T RJ-45 2000 Mbps 4-pair
UTP/STP
Cat. 5
100 m
1000Base-SX SC, ST 2000 Mbps MMF
(62.5μm)
220 m
2 km
1000Base-SX SC, ST 2000 Mbps MMF
(50μm)
550 m
1000Base-LX SC 2000 Mbps SMF (10μm) 10, 20, 50
km
1000Base-BX SC 2000 Mbps SMF (10μm) 20, 40 km
SFP
1000Base-SX Duplex LC 2000 Mbps MMF
(62.5μm)
550 m
2 km
1000Base-LX Duplex LC 2000 Mbps SMF (9μm) 10, 40, 60
km
1000Base-BX Duplex LC 2000 Mbps SMF (9μm) 70 km

EX45900 series www.etherwan.com
17
Cabling
Step 1: First, ensure the power of the switch and end devices are turned off.
<Note> Always ensure that the power is off before any installation.
Step 2: Prepare cable with corresponding connectors for each type of port
in use.
<Note> To connect two regular RJ-45 ports between switches or hubs, you need a
straight or cross-over cable.
Step 3: Consult the previous section for cabling requirements based on
connectors and speed.
Step 4: Connect one end of the cable to the switch and the other end to a
desired device.
Step 5: Once the connections between two end devices are made
successfully, turn on the power and the switch is operational.

EX45900 series www.etherwan.com
18
Specifications
Hardened PoE Gigabit
Ethernet Switch
4 x 10/100/1000Base-TX PoE ports with
RJ-45 connectors plus 1-port
10/100/1000Base-TX or
1000Base-SX/LX/BX, or Gigabit SFP socket
Applicable Standards IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX
IEEE 802.3ab 1000Base-T
IEEE 802.3z 1000Base-SX/LX
IEEE 802.1x Full-duplex Flow Control
IEEE 802.1az Energy Efficient Ethernet
IEEE 802.1p Quality of Service (QoS)
Forwarding Rate
10Base-T:
100Base-TX:
1000Base-T/SX/LX:
10 / 20Mbps half / full-duplex
100 / 200Mbps half / full-duplex
2000Mbps full-duplex
Performance 148,80pps for 10Mbps
148,810pps for 100Mbps
1,488,100pps for 1000Mbps
Cable
10Base-T:
100Base-TX:
1000Base-T:
1000Base-SX/LX:
2-pair UTP/STP Cat. 3, 4, 5
2-pair UTP/STP Cat. 5
4-pair UTP/STP Cat. 5
Up to 100m (328ft)
MMF (50 or 62.5μm), SMF (9 or10μm)
LED Indicators Per unit – Power, Fault
Per port – Link/Act, PoE (For PoE ports)
Dimensions 30mm (W) × 100mm (D) × 149mm (H)
(1.18” (W) × 4” (D) × 5.96” (H))
Net Weight 0.34Kg (0.75lb.)
Power Terminal Block: 24-48VDC
Power Consumption 7W Max (Device only, without PoE)
PoE Power Budget 120W
Operating
Temperature
-40°C to 75°C (-40°F to 167°F)
Storage Temperature -40°C to 85°C (-40°F to 185°F)
Humidity 5%-95% non-condensing
EMI FCC Part 15 Class A, VCCI Class A
EN61000-6-4
EN55022 Class A

EX45900 series www.etherwan.com
19
EMS EN61000-6-2:
EN61000-4-2 (ESD Standard)
EN61000-4-3 (Radiated RFI Standards)
EN61000-4-4 (Burst Standards)
EN61000-4-5 (Surge Standards)
EN61000-4-6 (Induced RFI Standards)
EN61000-4-8 (Magnetic Field Standards)
Environmental Test
Compliance
IEC60068-2-6 Fc (Vibration)
IEC60068-2-27 Ea (Shock)
FED STD 101C Method 5007.1 (Free Fall w/
package)