EtherWAN EX95000 Series User manual

W70G-EX95000Q2 Page 1
Installation Guide
EX95000 Series | Hardened Unmanaged Switch
Copyright 2023 EtherWAN Systems, Inc. All Rights Reserved 01/05/2023
1Unpacking
Open the carton and unpack the items. Your package
should include:
▪One EX95000 Switch
If any items are missing or damaged, notify your
EtherWAN representative. If possible, save the carton
and packing material in case you need to ship or store
the switch in the future.
2Equipment Needed
▪Category 5 or better cable for RJ-45 ports
▪Appropriate fiber cable for fiber ports
3Select a Location
▪Installation: DIN rail. Place the device on the DIN
rail from above using the slot. Push the front of
the device toward the mounting surface until it
audibly snaps into place.
▪Choose a dry area with ambient temperature
between -40 and 75°C (-40 and 167°F).
▪Keep away from heat sources, sunlight, warm air
exhausts, hot-air vents, and heaters.
▪Be sure there is adequate airflow.
4Connect to the Data Ports
Depending on the model, your switch can have the
following ports:
▪10/100BASE-TX: 16, 15 or 14 ports
▪100BASE-FX: 0, 1 or 2 ports
5Connect Power
Two power inputs are via a 12-48VDC terminal block,
and the third power input is via a 12VDC DC Jack.
Power consumption is:
▪7.4W Max. 0.6A@12VDC
▪0.3A@24VDC
▪0.15A@48VDC
Power Input Assignment
Power 3
12VDC
DC Jack
Power 2
+
12-48VDC
Terminal Block
-
Power Ground
Power 1
+
12-48VDC
-
Power Ground
Earth Ground
Relay Output
Rating
1A @ 24VDC
Relay Alarm Assignment
The relay contact closes if Power 1
and Power 2 both fail but Power 3 is on.
The relay contact closes if Power 3
fails but Power 1 and Power 2
are both on.
Power-Up Sequence
When the switch is powered up:
▪All Link/ACT LEDs blink momentarily.
▪The Power LEDs light up and stay lit.
▪LEDs for every port connected to a device will
flash, as the switch conducts a brief Power On Self-
Test (POST).

W70G-EX95000Q2 Page 2
Installation Guide
EX95000 Series | Hardened Unmanaged Switch
Copyright 2023 EtherWAN Systems, Inc. All Rights Reserved 01/05/2023
6LED Indicators
LED
State
Description
Power 1, 2, 3
(Green)
On
Switch is powered ON
correctly
Off
Switch is not receiving power
Alarm (Red)
On
Relay alarm on
Off
Relay alarm off
10/100BaseTX or 100Base FX/BX Ports
Link/Act
(Green)
On
Network connection
established
Off
No link
Blinking
Transmitting or receiving
data
7DIN Rail Installation
DIN-Rail Assembly Startup, and Dismantling
▪Assembly: Place the Switch on the DIN rail from
above using the slot. Push the front of the Switch
toward the mounting surface until it audibly snaps
into place.
▪Startup: Connect the supply voltage to start up the
Switch via the terminal block.
▪Dismantling: Pull out the lower edge and then
remove the Switch from the DIN rail.
Manufacturer information:
EtherWAN Systems, Inc.
33F, No. 93, Sec. 1, Xintai 5th Rd., Xizhi Dist., New
Taipei City, 221 Taiwan
The full product manual can be downloaded from:
www.etherwan.com