EtherWAN EX72000 User manual

Copyright ©2014 EtherWAN Systems, Inc. Page 1
All Rights Reserved
EX72000 rev. 1.0
12/2/2014
1 Unpacking
Unpack the items. Your package should include:
One EX72000 Series hardened managed
switch
Rack-mounting hardware brackets
One CD containing this user’s guide
If items are missing or damaged, notify your
EtherWAN representative. Keep the carton and
packing material.
2 What Else You Need
Appropriate cables for data ports
Personal computer or laptop
3 Select a Location
Desktop installations: Mount on a flat table
or shelf surface.
Rack installations: Use a 19-inch (48.3-
centimeter) EIA standard equipment rack
that is grounded and physically secure.
Identify a power source within 6 feet (1.8
meters).
Choose a dry area with ambient temperature
between -40 and 75ºC (-40 and 167ºF).
Keep away from heat sources, sunlight, warm
air exhausts, hot-air vents, and heaters.
Be sure there is adequate airflow.
Keep the switch at least 6 ft. (1.83 m) away
from the nearest source of electromagnetic
noise, such as a photocopy machine.
4 Connect to the Data Ports
Depending on the model, your switch can have
the following ports:
8, 12, 13, or 14 10/100Base-TX ports
0, 1, or 2 100Base-FX ports
0, 1, or 2 Gigabit ports
10/100Base-TX and 100Base-FX Ports
These ports come in 10/100Base-TX/FX/BX
interfaces. They can connect to devices such as
an IP surveillance camera or a Voice Over
Internet Protocol (VoIP) phone.
A. Insert one end of an appropriate cable into a
switch port.
B. Connect the other end into the Ethernet port
of the device.
C. Repeat steps A and B for each additional
device you want to connect to the switch.
Gigabit Ports
Some switch models have 1 or 2
10/100/1000Base-TX ports, 1000Base-SX/LX/BX
ports, or 2-port 1000Base SFP-combo
10/100/1000Base-TX ports.
You can connect these ports to network devices
such as a computer, printer, network video
recorder (NVR), network storage, or they can
connect to the network itself.
SFP-combo ports operate in “either/or” fashion.
This means that attaching to a 1 Gbps combo
port renders the equivalent partner combo port
unavailable.
5 Apply Power
The switch has two pairs of power inputs:
A 12-32VDC terminal block
A 12VDC jack
Only one power input is required to operate the
switch. However, redundant power supply
functionality is supported.
Terminal Block
The switch provides two power inputs on a 12-
32VDC terminal block. Only one power input is
required to operate the switch. The terminal
block has 4 terminal posts.
Pin Description
Power 2 +12-32VDC
−Power Ground
Power 1 +12-32VDC
−Power Ground
Earth Ground
Relay Output Rating 0.7A @ 12VDC, 0.35A @ 24VDC
EX72000 Managed Switch Installation Guide
Continued on next page

EX72000 Managed Switch Installation Guide
Copyright ©2014 EtherWAN Systems, Inc. Page 2
All Rights Reserved
EX72000 rev. 1.0
12/2/2014
DC Jack
Pin Description
Power 3 12VDC
Power-Up Sequence
When you apply power, all Link/ACT LEDs blink
momentarily, the Power 1/2/3 LEDs go ON, and
LEDs for every port connected to a device flash.
6 Front Panel LEDs
LED Color Status
Power 1
Power 2
Power 3
Green ON = power on.
OFF = power off.
10/100Base-TX, 100Base-FX/BX LEDs
Link/Act Green ON = valid network connection is established.
Flashing = port sending or receiving data.
10/100 Green ON = valid port connection at 100 Mbps.
OFF = valid port connection at 10 Mbps.
10/100/1000Base-TX LEDs
Link/Act Green ON = valid network connection is established.
Flashing = port sending or receiving data.
1000Base-SX/LX/BX LEDs
Link/Act Orange ON = valid network connection is established.
Flashing = port sending or receiving data.
LED Color Status
1000 Green ON = valid port connection at 1000 Mbps.
OFF = valid port connection at 10 or 100
Mbps.
SFP Green ON = valid SFP connection is established.
7 Managing the Switch
A. Connect a PC to an available switch port
using an appropriate cable.
B. Confirm that the Link/ACT LED for the switch
port to which the PC is connected is ON. If
not, choose a different port.
C. Configure the PC’s TCP/IP settings to use the
subnet 192.168.1.Xand subnet mask
255.255.255.0, where Xis a number from 2
to 254 other than 10.
D. In a Web browser address bar, type
http://192.168.1.10 and press Enter.
E. Log in to the management interface:
F. Change the system name:
- In the left pane, click +next to System,
then click System Name/Password.
- On the right side, click in the System
Name text box.
- Replace the name shown with a name you
want to assign to the switch.
- Click the Update Setting button below
the System Name text box.
G. By default there is no password assigned to
the switch. To add a password:
- In the page above, click in the Password
text box, enter a password, and retype it
in the Retype Password text box.
- Click Update Setting below the
Retype Password text box.
H. Change the switch’s IP address and subnet
mask to match the scheme on your network: