EVBIKE C961 User manual

INSTALLATION MANUAL
LCD display C961
EVLCD-CMS-C961

Importer: PHOYLO LTD, CZ684609501,
Enterprise House, Pass Street 2, 0L9 6HZ Oldham,
Manchester, UK
Contens:
1/ INSTALATION
2/ BASE SETTINGS
3/ ADVANCE SETTINGS
4/ ERROR CODES
Thank you for purchasing EVBIKE product and we hope that you will become a happy user. Carefully read the
entire manual prior to installation and first use! If you find any fact in the manual that would prevent you
from using our product, please contact your reseller for further discussion and keep the original packaging. The
reseller will advise you how to proceed properly.

Importer: PHOYLO LTD, CZ684609501,
Enterprise House, Pass Street 2, 0L9 6HZ Oldham,
Manchester, UK
The C961 display is made of ABS and is designed to perform well under -20º to 60 º C.
Available colors: Black.
DIMENSION OF DISPLAY
Size (Unit: mm). Pictures –LCD display, holder for LCD display.
During instalation, is possible to use spacers to fill the gap between the handlebar and holder of the display.
During installation, use reasonable force to not break the holder.. A typical installation is shown below.
The most common site of installation of the display is in the middle of the handlebar.

Importer: PHOYLO LTD, CZ684609501,
Enterprise House, Pass Street 2, 0L9 6HZ Oldham,
Manchester, UK
LCD CONTROL PANEL DISPLAYS:
-Multiple Power levels settings (Mode)
-Remaining Battery Capacity
-Speed (Speed/ MAX/AVG)
-Distance and Odometer (TRIP/ TOTAL)
-Time
-Assist walking (slow speed motor assist)
-Backlight
-Error codes
---------------------------------------------------------------------------------------------------------------------------------------------------
INTERFACE:
---------------------------------------------------------------------------------------------------------------------------------------------------
BUTTON:

Importer: PHOYLO LTD, CZ684609501,
Enterprise House, Pass Street 2, 0L9 6HZ Oldham,
Manchester, UK
CAUTON! Do not plug in or unplug this display when the power to the unit is on.
Avoid collisions
Protect the display’s membrane to provide water resistant performance.
Do not attempt to reset parameters if the display is not working..
Call for service if the C961 display is not working
---------------------------------------------------------------------------------------------------------------------------------------------------
INSTALATION
Install the display and button control on the handlebar and adjust its location. Plug it into the controller with
power off.
---------------------------------------------------------------------------------------------------------------------------------------------------
ON / OFF
To turn the unit on, press and hold the button to start the display. A long press again will switch it off.
The display switches off automaticlly if there is no aktivity for 10 minutes
(default).
---------------------------------------------------------------------------------------------------------------------------------------------------
WALKING ASSIST
Press and hold to start the walking assist. You will see the walking icon on the display and the motor
will move the bicycle or vehicle at 6km/h.
This function is designed for walking alongside only. Please do not use this function
when riding.
----------------------------------------------------------------------------------------------------------------------------------

Importer: PHOYLO LTD, CZ684609501,
Enterprise House, Pass Street 2, 0L9 6HZ Oldham,
Manchester, UK
BACKLIGHT
Press and hold to turn on the C961’s backlight screen. If a front light is configured as well, this will switch it
on as well if front light available.. Press and hold again to switch it off.
Note: The automatic backlight is available only if the controller (or built-in controller) offers this
function.
If the controller has a light sensor inside of it, the back light & front light will switch on automatically
according to the level of darkness. The automatic function is off when the display is in manual mode.
---------------------------------------------------------------------------------------------------------------------------------------------------
POWER LEVEL
The display is integrated with the controller to provide several levels of power. Press or to change the
levels. . Default range is 0 - 3, where 0 means no output, and 3 means maximum output. The default switch-on
is level 1.
---------------------------------------------------------------------------------------------------------------------------------------------------
BATTERY CAPACITY
Four sections highlights when battery is full. Percentage of capacity for sections:
The battery icon flashes at 1 Hz when low power.
---------------------------------------------------------------------------------------------------------------------------------------------------

Importer: PHOYLO LTD, CZ684609501,
Enterprise House, Pass Street 2, 0L9 6HZ Oldham,
Manchester, UK
DISTANCE (TRIP AND ODOMETER)
Press to shift between TRIP and TOTAL (Odometer).
---------------------------------------------------------------------------------------------------------------------------------------------------
TRIP RESET
With the power on, Press and hold both and clear TRIP distance. -------------------------------------------------
--------------------------------------------------------------------------------------------------
ERROR CODES
When something goes wrong with system, an error code will flash on the display. Check details on attached list.
The motor will stop working in the event of an error. Only when the error is gone, will the motor work
again.

Importer: PHOYLO LTD, CZ684609501,
Enterprise House, Pass Street 2, 0L9 6HZ Oldham,
Manchester, UK
---------------------------------------------------------------------------------------------------------------------------------------------------
DISPLEY SETTINGS
---------------------------------------------------------------------------------------------------------------------------------------------------
PREPARATION
Makes sure the connections are good, then power on.
---------------------------------------------------------------------------------------------------------------------------------------------------
SETTING
Press and hold to turn on the display. Press and hold the and to set the mode
UNIT
Press to change unit Km or Mile.
Press to save and go to set speed.

Importer: PHOYLO LTD, CZ684609501,
Enterprise House, Pass Street 2, 0L9 6HZ Oldham,
Manchester, UK
SETTING THE SPEED LIMIT
To limit the speed range (from 15Km/h to 40Km/h), press or to change the limit up or down.
Press to save & go to set backlight.
BACKLIGHT
Press or to change the brightness (range is 1 to 8).
Press to save & go to time setting.

Importer: PHOYLO LTD, CZ684609501,
Enterprise House, Pass Street 2, 0L9 6HZ Oldham,
Manchester, UK
TIME
Press or to change the hour, then press to save & go to the minute setting. Press or to
change the minutes.
Press to save & exit.
The settings go into effect after restart.
---------------------------------------------------------------------------------------------------------------------------------------------------
ADVANCE SETTING
Press and hold to start the display. Press and hold both and to enter setting mode.
Press and and do not release, meanwhile press eight times to go to the advanced setting menu.

Importer: PHOYLO LTD, CZ684609501,
Enterprise House, Pass Street 2, 0L9 6HZ Oldham,
Manchester, UK
WHEEL SIZE SETTING
Press or to change the wheel size. Range from 8 to 32 inch. Pressto save & go to sleep time interval
setting.
Sleep time interval setting
Press or to change the time, range from 0 to 60 minutes.
Display will sleep and cut off power after no operation on system for the selected time. Press to save and
skip to level amount setting.

Importer: PHOYLO LTD, CZ684609501,
Enterprise House, Pass Street 2, 0L9 6HZ Oldham,
Manchester, UK
Power level amount setting
Press or to change the amount. The range from 0 –3 to 0 - 9 levels
Press to save and exit.
The settings go into effect after restart.
---------------------------------------------------------------------------------------------------------------------------------------------------
FAQ
Q: Why does the display not power on?
A: Please check that the battery is connected and has power. Then check all the wires and connections.
Then press the ON/OFF button again. If this fails, please see your service technician.
Q: What should I do when an error code is displayed?
A: Please check the error code list. Sometimes powering down the unit (press ON/OFF), then unplugging the
display, leave it unplugged for two minutes and then plugging it back in and turning it on will reset and
correct the error. Please call your service technician if the user cannot remove the error.

Importer: PHOYLO LTD, CZ684609501,
Enterprise House, Pass Street 2, 0L9 6HZ Oldham,
Manchester, UK
ERROR CODES
Error
explanation
04
Throttle not returning to zero state
05
Throttle abnormality
06
Low voltage protection
07
Over voltage protection
08
Hall sensor abnormality
09
Phase line abnormality
10
Controller overheat
11
Temperature sensor in controller abnormality
12
Current sensor abnormality
21
Speed sensor abnormality