evertz 2430GDAC-WARP User manual

Model 2430GDAC-WARP
G-Link D to A Converter
Instruction Manual
© Copyright 2004, 2008
EVERTZ MICROSYSTEMS LTD.
5288 John Lucas Drive,
Burlington, Ontario,
Canada, L7L 5Z9
Phone: [phone]
Sales Fax: [phone]
Service Fax: [phone]
Internet: Sales: [email protected]
Tech Support: [email protected]
Web Page: http://www.evertz.com
Version 1.2 June 2008
The material contained in this manual consists of information that is the property of Evertz Microsystems and is
intended solely for the use of purchasers of the 2430GDAC-WARP GLink D to A Converter. Evertz Microsystems
expressly prohibits the use of this manual for any purpose other than the operation of the Downconverter.
All rights reserved. No part of this publication may be reproduced without the express written permission of
Evertz Microsystems Ltd. Copies of this guide can be ordered from your Evertz products dealer or from Evertz
Microsystems.

INFORMATION TO USERS IN EUROPE
NOTE
CISPR 22 CLASS A DIGITAL DEVICE OR PERIPHERAL
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to the European Union EMC directive. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
INFORMATION TO USERS IN THE U.S.A.
NOTE
FCC CLASS A DIGITAL DEVICE OR PERIPHERAL
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
WARNING
Changes or Modifications not expressly approved by Evertz Microsystems Ltd. could void the user’s
authority to operate the equipment.
Use of unshielded plugs or cables may cause radiation interference. Properly shielded interface cables
with the shield connected to the chassis ground of the device must be used

2430GDAC G-Link D to A Converter
Revision 1.2
REVISION HISTORY
REVISION DESCRIPTION DATE
1.0 Original release version May 04
1.1 Added Fiber handling instructions Aug 04
1.2 Fixed formatting Jun 08
Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof
nor for the rights of third parties, which may be effected in any way by the use thereof. Any representations in this document concerning
performance of Evertz products are for informational use only and are not warranties of future performance, either express or implied. The
only warranty offered by Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order
confirmation form.
Although every attempt has been made to accurately describe the features, installation and operation of this product in this manual, no
warranty is granted nor liability assumed in relation to any errors or omissions unless specifically undertaken in the Evertz sales contract or
order confirmation. Information contained in this manual is periodically updated and changes will be incorporated into subsequent editions. If
you encounter an error, please notify Evertz Customer Service department. Evertz reserves the right, without notice or liability, to make
changes in equipment design or specifications.

2430GDAC G-Link D to A Converter
Revision 1.2
This page left intentionally blank

2430GDAC G-Link D to A Converter
Revision 1.2
TABLE OF CONTENTS
1. OVERVIEW..................................................................................................................................... 1
2. INSTALLATION.............................................................................................................................. 2
2.1. POWER.................................................................................................................................. 2
2.2. GLINK IN AND OUT............................................................................................................... 2
2.3. VIDEO OUT............................................................................................................................ 3
2.4. FIRMWARE UPGRADE PORT.............................................................................................. 3
2.5. CARE AND HANDLING OF OPTICAL FIBER ...................................................................... 4
2.5.1. Safety.......................................................................................................................... 4
2.5.2. Handling And Connecting Fibers................................................................................ 4
2.5.3. Making Sure The Optical Fibers Are Clean ................................................................ 4
2.6. DISPLAY SETUP................................................................................................................... 4
3. SPECIFICATIONS .......................................................................................................................... 6
3.1. COAXIAL GLINK INPUT........................................................................................................6
3.2. FIBER GLINK INPUT............................................................................................................. 6
3.3. RE-CLOCKED COAXIAL GLINK OUTPUT........................................................................... 6
3.4. VIDEO OUTPUT..................................................................................................................... 6
3.5. DVI DIGITAL VIDEO OUTPUT .............................................................................................. 6
3.6. RGB ANALOG VIDEO OUTPUT ........................................................................................... 6
3.7. ELECTRICAL......................................................................................................................... 6
3.8. PHYSICAL.............................................................................................................................. 7
4. STATUS LED’S............................................................................................................................... 7
5. USER CONTROLS ......................................................................................................................... 7
5.1.1. Input Source Selection................................................................................................ 7
5.1.2. Video Resolution.........................................................................................................7
6. UPGRADING THE FIRMWARE...................................................................................................... 8
6.1. REQUIREMENTS................................................................................................................... 8
6.2. UPDATE PROCEDURE......................................................................................................... 8
6.2.1. Part 1 – Configuring the unit for firmware upgrades................................................... 8