evertz X-9512 User manual

Model X-9512
12 x 1 SDI Router
&
Model X-HD9512
12 x 1 High Definition Router
Instruction Manual
© Copyright 1999, 2000, 2001
EVERTZ MICROSYSTEMS LTD.
5288 John Lucas Drive,
Burlington, Ontario, Canada,
L7L 5Z9
Phone: [phone]
Sales Fax: [phone]
Support Fax: [phone]
Internet: Sales: [email protected]
Tech Support: [email protected]
Web Page: http://www.evertz.com
Version 1.2 May 2001
The material contained in this manual consists of information that is the property of Evertz Microsystems and is
intended solely for the use of purchasers of the X-9512 and X-HD9512 Routers. Evertz Microsystems expressly
prohibits the use of this manual for any purpose other than the operation of the Router.
All rights reserved. No part of this publication may be reproduced without the express written permission of Evertz
Microsystems Ltd. Copies of this guide can be ordered from your Evertz products dealer or from Evertz
Microsystems.

INFORMATION TO USERS IN EUROPE
NOTE
CISPR 22 CLASS A DIGITAL DEVICE OR PERIPHERAL
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to the European Union EMC directive. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
INFORMATION TO USERS IN THE U.S.A.
NOTE
FCC CLASS A DIGITAL DEVICE OR PERIPHERAL
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
WARNING
Changes or Modifications not expressly approved by Evertz Microsystems Ltd. could
void the user’s authority to operate the equipment.
Use of unshielded plugs or cables may cause radiation interference. Properly shielded
interface cables with the shield connected to the chassis ground of the device must be
used.

X-9512 and X-HD9512 Series Router Manual
REVISION HISTORY
REVISION DESCRIPTION DATE
1.0 Original Version June 99
1.1 Updated Menu structure to support GVG Ten XL protocol and GPI Mode Aug 00
1.2 Updated Table 2-4 to correct Pinout labels May 01
1.3 Added DIP switch 5 to Table 4-1 Feb 02

X-9512 and X-HD9512 Series Router Manual
TABLE OF CONTENTS Revision 1.2 i
TABLE OF CONTENTS
1. OVERVIEW....................................................................................................................................... 1-1
1.1. HOW TO USE THIS MANUAL..................................................................................................... 1-1
1.2. GLOSSARY ................................................................................................................................. 1-2
2. INSTALLATION................................................................................................................................ 2-1
2.1. REAR PANEL .............................................................................................................................. 2-1
2.1.1. Digital Video Connections (X-9512) ...................................................................................... 2-1
2.1.2. High Definition Digital Video Connections (X-HD9512) ........................................................ 2-1
2.1.3. Remote Control Connections................................................................................................2-1
2.1.4. Gen Lock Video Connections................................................................................................2-2
2.1.5. Power Connections............................................................................................................... 2-3
2.2. MOUNTING .................................................................................................................................. 2-3
2.3. POWER REQUIREMENTS ..........................................................................................................2-3
2.3.1. Selecting the Correct Mains Voltage..................................................................................... 2-3
2.3.2. Changing the Fuses.............................................................................................................. 2-3
2.4. CONNECTING THE REMOTE CONTROL PANEL ..................................................................... 2-4
2.5. CONNECTING THE GENERAL PURPOSE INPUTS AND OUTPUTS ....................................... 2-5
2.6. CONTROLLING THE ROUTER USING THE EXTERNAL SERIAL PROTOCOL....................... 2-9
2.6.1. Connecting the Router to a Grass Valley Ten XL ASCII Control Device .............................. 2-9
3. OPERATION..................................................................................................................................... 3-1
3.1. OVERVIEW OF THE FRONT PANEL DISPLAY AND CONTROLS ........................................... 3-1
3.1.1. Video Router Controls........................................................................................................... 3-1
3.1.2. Setup Key Group................................................................................................................... 3-1
3.1.3. Dual Button Keystrokes......................................................................................................... 3-2
3.2. LED STATUS INDICATORS........................................................................................................ 3-2
3.3. FRONT PANEL SETUP MENU ................................................................................................... 3-3
3.3.1. Selecting the Video Reference Type..................................................................................... 3-4
3.3.2. Selecting how the Analog Video Reference aligns with the Digital HD signals
(X-HD9512 series only)......................................................................................................... 3-4
3.3.3. Selecting the Video Line when the Switch will Occur............................................................ 3-4
3.3.4. Selecting the External Remote Control Protocol................................................................... 3-4
3.3.5. Selecting the Baud Rate for External Remote Control Port .................................................. 3-4
3.3.6. Selecting the Serial Data Format for External Remote Control Port ..................................... 3-5
3.3.7. Selecting the Serial Address................................................................................................. 3-5

X-9512 and X-HD9512 Series Router Manual
ii Revision 1.2 TABLE OF CONTENTS
3.3.8. Selecting the Serial Data Control Mode ................................................................................ 3-5
3.3.9. Selecting the General Purpose Contact Closure Output Functions ...................................... 3-5
3.3.10. Selecting the Operating Mode of the General Purpose Inputs.............................................. 3-6
3.3.11. Setting the Front Panel Display Brightness........................................................................... 3-6
3.3.12. How to Restore the Factory Default Settings ........................................................................ 3-6
3.3.13. How to Update the Router Software ..................................................................................... 3-7
3.4. LABELLING THE SOURCES ...................................................................................................... 3-7
3.5. CONTROLLING THE VIDEO BUS CROSSPOINTS FROM THE GPI INPUTS .......................... 3-7
4. TECHNICAL DESCRIPTION............................................................................................................ 4-1
4.1. SPECIFICATIONS ....................................................................................................................... 4-1
4.1.1. Video Specifications X-9512 ................................................................................................. 4-1
4.1.1.1. SD Video Inputs .............................................................................................................. 4-1
4.1.1.2. SD Video Output ............................................................................................................. 4-1
4.1.2. Video Specifications X-HD9512 ............................................................................................ 4-1
4.1.2.1. HD Video Inputs .............................................................................................................. 4-1
4.1.2.2. HD Video Outputs ........................................................................................................... 4-2
4.1.3. Gen Lock Input...................................................................................................................... 4-2
4.1.4. Electrical................................................................................................................................ 4-2
4.2. DIP SWITCH SETTINGS ............................................................................................................. 4-2
4.3. UPDATING THE FIRMWARE IN THE ROUTER ......................................................................... 4-3
4.3.1. Connecting the Computer to the Router ............................................................................... 4-3
4.3.2. Initiating Programming Mode ................................................................................................ 4-3
4.3.2.1. Setup Menu Method ........................................................................................................ 4-3
4.3.2.2. DIP Switch Method.......................................................................................................... 4-4
4.3.3. Programming the MCU Using WINISP ................................................................................. 4-4
4.3.3.1. WINISP Configuration Setup........................................................................................... 4-4
4.3.3.2. Confirming Communications with the Router .................................................................. 4-5
4.3.3.3. Reprogramming the Boot Vector and Status Byte .......................................................... 4-5
4.3.3.4. Reprogramming the Microcontroller in the Router .......................................................... 4-5
5. CONTROLLING 95XX ROUTERS USING GVG TEN-XL ASCII PROTOCOL ................................ 5-1
5.1. SERIAL DATA FORMAT ............................................................................................................. 5-1
5.2. DEFINITIONS............................................................................................................................... 5-1
5.3. COMMAND FORMATS................................................................................................................ 5-2
5.3.1. Write or Take Command ....................................................................................................... 5-2
5.3.2. Read or Query Command .....................................................................................................5-3
5.3.3. Reply Command String ......................................................................................................... 5-3

X-9512 and X-HD9512 Series Router Manual
TABLE OF CONTENTS Revision 1.2 iii
5.4. COMMAND EXAMPLES: ............................................................................................................ 5-3
5.4.1. Input Selection – Audio Follow Mode.................................................................................... 5-3
5.4.2. Input Selection – Breakaway Mode....................................................................................... 5-4
5.4.3. Router Status Request.......................................................................................................... 5-4
Figures
Figure 2-1: Rear Panel Layout .............................................................................................................. 2-1
Figure 2-2: General Purpose I/O Schematic ......................................................................................... 2-6
Figure 2-3: Powering the General Purpose Input Opto Isolators from the Router ................................ 2-7
Figure 2-4: Powering the General Purpose Input Opto Isolators from an External Power Supply........ 2-7
Figure 2-5: Powering the General Purpose Output Opto Isolators from the Router.............................. 2-8
Figure 2-6: Powering the General Purpose Output Opto Isolators from an External Power Supply ..... 2-8
Figure 3-1: Front Panel Layout.............................................................................................................. 3-1
Figure 3-2: Overview of the Setup Menu............................................................................................... 3-3
Tables
Table 2-1: COM 1 Pin Definitions.......................................................................................................... 2-2
Table 2-2: GPIO/COM2 Pin Definitions................................................................................................. 2-2
Table 2-3: GPIO/COM2 Y Adapter Cable (WA-S36)............................................................................. 2-4
Table 2-4: Remote Control Panel Extender Cable ................................................................................ 2-5
Table 2-5: Master 9512 to Slave 9512 Cable........................................................................................ 2-9
Table 3-1: Selecting the Video Input Busses with the GPI Inputs......................................................... 3-7
Table 4-1: DIP Switch Settings.............................................................................................................. 4-2
Table 4-2: Cable to Connect PC to Router for Updating Firmware ....................................................... 4-3
Table 5-1: Crosspoint numbers and their Internal Source Numbers ..................................................... 5-2
Table 5-2: ASCII Command Definitions ................................................................................................ 5-2

X-9512 and X-HD9512 Series Router Manual
iv Revision 1.2 TABLE OF CONTENTS
This page left intentionally blank

X-9512 and X-HD9512 Series Router Manual
Revision 1.3
TABLE OF CONTENTS
1. OVERVIEW....................................................................................................................................... 1-1
1.1. HOW TO USE THIS MANUAL..................................................................................................... 1-1
1.2. GLOSSARY ................................................................................................................................. 1-2

X-9512 and X-HD9512 Series Router Manual
Revision 1.3
This page left intentionally blank