EVOC EC0-1814 User manual

EC0-1814(B)
Embedded ATX 带 VGA/2LAN/6COM
Embedded ATX with VGA/2LAN/6COM
Version: C00

Copyright Notice
Information offered in this manual is believed to be correct at the time of printing, and
is subject to change without prior notice in order to improve reliability, design and
function and does not represent a commitment on the part of the manufacturer. In no
event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of improper installation and/or use, or inability to
use the product or documentation.
This user manual is protected by copyright. No part of this manual may be reproduced,
stored in any retrieval system, or transmitted, in any form or by any means,
mechanical, electronic, photocopied, recorded or otherwise, without the prior written
permission from the manufacturer.
Trademarks
EVOC is a registered trademark of EVOC Intelligent Technology Co., Ltd. Other
product names mentioned herein are used for identification purposes only and may be
trademark and/or registered trademarks of their respective companies.
Please visit our website: http://www.evoc.com for more information, or send an
email to the Technical Support Mailbox [email protected] (International) or
[email protected] (Domestic) for consultation.
Hotline: [phone]

Safety Instructions
1. Please read this manual carefully before using the product;
2. Leave the board or card in the antistatic bag until you are ready to use it;
3. Touch a grounded metal object (e.g. for 10 seconds) before removing the board
or card from the anti-static bag;
4. Before installing or removing a board, wear the ESD gloves or ESD wrist strap;
handle the board by its edges only;
5. Before inserting, removing or re-configuring motherboards or expansion cards,
first disconnect the computer and peripherals from their power sources to
prevent electric shock to human bodies or damage to the product;
6. Remember to disconnect the AC power cord from the socket before removing
the board or moving the PC;
7. For PC products, remember to disconnect the computer and peripherals from the
power sources before inserting or removing a board;
8. Before connecting or disconnecting any terminal, peripheral or any device, be
sure the system is powered off and all the power sources are disconnected;
9. After turning off the computer, wait at least 30 seconds before turning it back on

Contents
Chapter 1 Product Introduction.....................................................................................1
Overview ......................................................................................................................1
Mechanical Dimensions, Weight and Environment ......................................................1
Typical Consumption....................................................................................................1
Microprocessor .............................................................................................................2
Chipset..........................................................................................................................2
System Memory............................................................................................................2
Graphics Function.........................................................................................................2
Network Function .........................................................................................................3
Audio Function.............................................................................................................3
Power Feature...............................................................................................................3
Expansion Bus ..............................................................................................................3
Watchdog Function.......................................................................................................3
Operating System .........................................................................................................3
On-board I/O.................................................................................................................3
Chapter 2 Installation....................................................................................................5
Product Outline.............................................................................................................5
Locations of Connectors ...............................................................................................6
Structure .......................................................................................................................7
Jumper Setting ..............................................................................................................8
Serial Port .....................................................................................................................9
USB Port.......................................................................................................................9
LAN Port ....................................................................................................................10
Power Connector ........................................................................................................11
Audio Connector.........................................................................................................12
SATA Connector .........................................................................................................12

Hot-swap of SATA Hard Disk.....................................................................................12
Keyboard and Mouse Connector ................................................................................15
VGA Graphic Connector ............................................................................................15
GPIO Connector .........................................................................................................15
LPT Connector ...........................................................................................................16
IDE Connector............................................................................................................16
Floppy Driver Connector............................................................................................17
Status Indicator and Control Connector......................................................................18
Fan Connector.............................................................................................................18
PCI Slot ......................................................................................................................19
PCIex16 Slot...............................................................................................................21
PCIex4 Slot.................................................................................................................22
Install the CPU............................................................................................................23
Install the CPU Fan.....................................................................................................23
Chapter 3 BIOS Setup ................................................................................................25
BIOS Overview ..........................................................................................................25
BIOS Parameter Setup................................................................................................25
Basic Function Setting for BIOS ................................................................................26
System Resource Managed by BIOS under X86 Platform .........................................38
Chapter 4 Install the Drivers.......................................................................................42
Appendix ....................................................................................................................43
Watchdog Programming Guide...................................................................................43
Digital IO Programming Guide ..................................................................................45
Troubleshooting and Solutions ...................................................................................47

Chapter 1 Product Introduction
EC0-1814(B) - 1 -
Chapter 1 Product Introduction
Overview
EC0-1814(B) is a high-performance Embedded ATX motherboard, which adopts
G41+ICH7R platform to realize high-performance design. It provides VGA single
display, two 10/100/1000Mbps LAN ports, six serial ports, eight USB ports, four
SATA connectors, one IDE connector and one FDC connector; therefore, the board
provides abundant connector choices for customers. It also provides one PCIe x16
expansion slot, one PCIe x4 expansion slot and four PCI expansion slots, which
provides abundant expansion choices for customers.
The product realizes high-performance as well as miniature design; thus, it can satisfy
the embedded requirements for such industries as ATM, POS, NET and Media, etc.
Mechanical Dimensions, Weight and Environment
Dimensions: 304.8mm (L) x 251.2mm (W) x 41.2mm (H);
Net Weight: 0.66Kg;
Operating Environment:
Temperature: -5C ~ 60C;
Humidity: 5% ~ 90% (non-condensing);
Storage Environment:
Temperature: -40C ~ 80C;
Humidity: 5% ~ 90% (non-condensing);
Typical Consumption
The typical consumption is based on the following idle status values.

Chapter 1 Product Introduction
- 2 - EC0-1814(B)
CPU: Intel®/Yorkfield/Core2Quad/Q9300/2.50GHz/6M/1333/SLAWE/M1/95W(10677h)
Memory: DDR3 1333 2GB Apacer x2
Operating System: Windows XP/32bit/Chinese SP3
Hard Disk: HITACHI HDP725025GLA380 250GB 7200RPM 8M SATA
+5V@ 1.38 A; +5%/-3%;
+3.3V@ 2.02 A; +5%/-3%;
+12V@ 0.66 A; +5%/-3%.
Microprocessor
Supports Intel® Core™2 Duo/Quad E7000, E8000&Q9000 series, Intel® Pentium®
E6000, E5000 and E2000 series and Intel® Celeron® E1000, E3000 and 400 series
CPU of LGA775 package, FSB: 800/1066/1333MHz
Intel® Core™2 Extreme QX9000 series CPU is not supported.
Chipset
Intel® G41 + Intel® ICH7R
System Memory
Provides two 240Pin DDR3 memory slots, supporting 800/1066MHz Un-buffered
non-ECC memory. The maximum memory capacity supported by a single memory
module is up to 2GB, while that supported by the board is up to 4GB.
Graphics Function
Supports VGA single display and hot swap function;
The maximum resolution and refresh rate supported is up to 2048x1536@75Hz.

Chapter 1 Product Introduction
EC0-1814(B) - 3 -
Network Function
Provides two 10/100/1000Mbps LAN ports; the LAN port in J2 (LAN1) supports S1,
S4 and S5 and Wake-on-LAN function.
Audio Function
Adopts HDA standard, supporting MIC-IN/LINE-IN/LINE-OUT.
Power Feature
Adopts ATX power, supporting S0, S1, S4 and S5 functions;
Expansion Bus
Provides four 32-bit PCI slots, one PCIE x16 slot and one PCIE x4 slot.
Watchdog Function
255 levels, programmable by minute or second;
Supports watchdog timeout interrupt or reset system.
Operating System
Supported OSs: Windows XP and Linux;
On-board I/O
Six serial ports, COM1 and COM2 support RS-232/RS-422/RS-485 mode
selection; Modem wake-up function is not supported;
One IDE connector;
Four SATA 2.0 connector, supporting hot swap function;
One FDD connector;
Eight USB 2.0 port;
One PS/2 keyboard and mouse connector;

Chapter 1 Product Introduction
- 4 - EC0-1814(B)
One 8-chanenl digital I/O.
Tips: how to identify the alarms
1. Long “beep” indicates system memory error;
2. Short “beep” indicates to power on the computer.

Chapter 2 Installation
EC0-1814(B) - 5 -
Chapter 2 Installation
Product Outline
H1 H8 H2
H10
H6
H4
H5
H7
H9
H3
Unit: mm
Warning!
Please adopt appropriate screws and proper installation methods (including
board allocation, CPU and heat sink installation, etc); otherwise, the board may
be damaged. It is recommended to use M3x6 GB9074.4-88 screws at H1 ~ H10.

Chapter 2 Installation
- 6 - EC0-1814(B)
Locations of Connectors
H1 H8 H2
AUDIO1
J3 J2
J1 KM1
H10
PWR2
PCIE2
PCI1 PCI2 PCI3 PCI4
PCIE1
GPIO1
COM2
COM3
COM4
COM5
COM6
JP1
JP2 JP3
JP4 JP5
JP6
JP7
JP8
JP9
JP10
JP11
JP12
CPUFAN1
PWR1
H6
FP1 FP3
FP2
H4
J5 SATA1 SATA2
SATA3 SATA4
J4
H5
FDD1
H7 SYSFAN1 IDE1
DIMM1
DIMM2
H9
H3
JCC1

Chapter 2 Installation
EC0-1814(B) - 7 -
Structure
FDD
4*PCI SLOT
1*PCIe X4SLOT
1*PCIe X16SLOT
LPC TO
UART
IDE
COM3 COM4 COM5 COM6
PATA
PCIe
PCI BUS
Display Interface
Fan Control
PCIe x4
ICH7R
Mouse
LGA775 Processor
Parallel
SATA
DDR3
SPI Flash
CH B
Hardware Monitor
HDA Audio
LAN2
RJ45
DIMM2
NH82801GR
LAN1
GMCH
LPC SIO
SATA Port 1~4
CH A
DMI X4
10/100/1000
Mbps LAN
USB 2.0
G41
Fan Control
VGA
MAX =24W
RJ45
DIMM1
MAX =3.3W
SPI
Keyboard
Connector
Connector
PCI-E Port 6
DDR3
USB 2.0
COM2
HDA
COM1
PCI-E Port5
LPC Bus
USB PORT 4~7
USB PORT 0~3
FSB
Bus
8GPIO
10/100/1000
Mbps LAN
Tip: How to identify the first pin of the jumpers and connectors
1. Observe the letter beside the socket: the first pin is usually marked with “1” or
bold lines or triangular symbols;
2. Observe the solder pad on the back; the square pad is the first pin.

Chapter 2 Installation
- 8 - EC0-1814(B)
Jumper Setting
1. JCC1: Clear/Keep CMOS Setting (Pitch: 2.54mm)
CMOS is powered by the button battery on board. Clearing CMOS will restore
original settings (factory default). The steps are listed as follows: (1) Turn off the
computer and unplug the power cable; (2) Instantly short circuit JCC1; (3) Turn on
the computer; (4) Follow the prompt on screen to enter BIOS setup when booting the
computer, load optimized defaults; (5) Save and exit. Please set as follows:
Setup Function
1-2 Open Normal ((Default)
JCC1 1-2 Short Clear the contents of CMOS and all BIOS settings
will restore to factory default values.
2. JP1 ~ JP10: RS-232/RS-422/RS-485 Mode Selection for COM1 and COM2
(Pitch: 2.54mm)
Mode Selection
Pin
Setting RS-232 RS-485 RS-422
JP1 1-2 3-4 5-6
JP2 1-2 2-3 2-3
JP3 1-2 2-3 2-3
JP4 1-2 2-3 2-3
JP5 1-2 2-3 2-3
JP6 1-2 3-4 5-6
JP7 1-2 2-3 2-3
JP8 1-2 2-3 2-3
JP9 1-2 2-3 2-3
JP1/JP6
JP2 ~ JP5
JP7 ~ JP10 JP10 1-2 2-3 2-3
Note: JP1 ~ JP5 are used to set COM1; JP6 ~ JP10 are used to set COM2.
3. JP11 ~ JP12: Choose Voltage Mode for Serial Port with Power (Pitch:
2.54mm)
Setup Function
1-2 Short Normal ((Default)
3-4 Short Choose 5V Serial Port
JP11
/
JP12 5-6 Short Choose 12V Serial Port

Chapter 2 Installation
EC0-1814(B) - 9 -
Serial Port
The board provides one standard DB9 serial port and five 2x5Pin serial port (Pitch:
2.54mm). COM1 and COM2 support RS-232/RS-422/RS-485 mode. The board
adopts VGA+PRINTER+COM combo socket and the model is 1262-049-401-910-N
of ETL and the model of the corresponding terminal is 1165-109-001-000 of ETL or
the D-SUB 9Pin female terminals of other manufacturers.
Signal Name
COM1 ~ COM6 COM1/COM2
Pin
RS-232 RS-422 RS-485
1 DCD# TXD- Data-
2 RXD TXD+ Data+
3 TXD RXD+ NC
4 DTR# RXD- NC
5 GND GND GND
6 DSR# NC NC
7 RTS# NC NC
8 CTS# NC NC
9 RI# NC NC
J1(COM1)
COM2 ~ COM6
10 NA NA NA
Note: the data transmission direction is controlled automatically at RS-485 mode.
USB Port
The board provides two sets of RJ45+dual USB connectors (J2 and J3) and two sets
of 2x5Pin USB pin headers (J4 and J5, Pitch: 2.54mm), which can support eight USB
devices in all.
Pin Signal Name
1 +5V
2 USB_Data-
3 USB_Data+
J2/J3(USB) 4 GND
Note: it adopts RJ45+2USB combo socket of SUYIN 020180M500PM417ZA;

Chapter 2 Installation
- 10 - EC0-1814(B)
Pin Signal Name Pin Signal Name
1 +5V 2 +5V
3 USB1_Data- 4 USB2_Data-
5 USB1_Data+ 6 USB2_Data+
7 GND 8 GND
J4/J5
9 NA 10 GND
LAN Port
The board provides two 10/100/1000Mbps LAN ports, RJ45+dual USB connectors
(J2 and J3).
J2/J3(LAN)
LILED
(Dual-Color: Y/G) LAN Speed Indicator
ACTLED
(Green) LAN Activity Status Indicator Green 1000Mbps
Blink Data Transmitting Yellow 100Mbps
Off No Data to Transmit Off 10Mbps
Note: it adopts RJ45+2USB combo socket of SUYIN 020180M500PM417ZA.

Chapter 2 Installation
EC0-1814(B) - 11 -
Power Connector
1. 24 Pin ATX Power Connector (Pitch: 4.2mm)
Pin Signal Name Pin Signal Name
1 +3.3V 13 +3.3V
2 +3.3V 14 -12V
3 GND 15 GND
4 +5V 16 PS_ON#
5 GND 17 GND
6 +5V 18 GND
7 GND 19 GND
8 PWROK 20 -5V
9 +5VSB 21 +5V
10 +12V 22 +5V
11 +12V 23 +5V
PWR1
12 +3.3V 24 GND
2. ATX 12V Power Connector (Pitch: 4.2mm)
Pin Signal Name
1 GND
2 GND
3 +12V
PWR2
4 +12V

Chapter 2 Installation
- 12 - EC0-1814(B)
Audio Connector
Pin Signal Name
1 LINE_IN
2 LINE_OUT
AUDIO1 3 MIC_IN
SATA Connector
The board provides four standard SATA connectors, supporting RAID0, 1, 5 and 10.
Pin Signal Name
1 GND
2 TX+
3 TX-
4 GND
5 RX-
6 RX+
SATA1 ~ SATA4
7 GND
Hot-swap of SATA Hard Disk
Notes for hot-swap of SATA hard disk:
1. The hard disk shall support SATA 2.0 and use 15-pin SATA hard disk power
connector.
2. The driver of chipset shall support the hot-swap of SATA hard disk.
3. Hot-swap of SATA hard disk with the operating system is forbidden when system
is powered-on.

Chapter 2 Installation
EC0-1814(B) - 13 -
Please carry out hot plugging as follows. Improper operation may destroy the hard
disk or result in data loss.
Hot Plug
Step 1: Please plug the 1 x 4 pin SATA power connector (white) into the power adapter.
Step 2: Please connect the SATA data cable to the SATA connector on board.
Step 3: Please connect the 15-pin SATA power connector (black) to the SATA hard
disk.
SATA Data Cable SATA Power Cable

Chapter 2 Installation
- 14 - EC0-1814(B)
Step 4: Please connect the SATA data cable to the SATA hard disk.
Hot Unplug
Step 1: Uninstall the hard disk from the device manager.
Step 2: Unplug the data cable from the SATA hard disk.
Step 3: Unplug the SATA 15-pin power connector (black) from the SATA hard disk.

Chapter 2 Installation
EC0-1814(B) - 15 -
Keyboard and Mouse Connector
Pin Signal Name Pin Signal Name
1 KB_DATA 2 NC
3 GND 4 +5V
5 KB_CLK 6 NC
7 MS_DATA 8 NC
9 GND 10 +5V
KM1 11 MS_CLK 12 NC
VGA Graphic Connector
It adopts VGA+PRINTER+COM combo socket of ETL 1262-049-401-910-N; please
choose appropriate D-SUB 15Pin male terminal.
Pin Signal Name Pin Signal Name
1 Red 2 Green
3 Blue 4 NC
5 GND 6 GND
7 GND 8 GND
9 NC 10 GND
11 NC 12 DDCDATA
13 HSYNC 14 VSYNC
J1(VGA1)
15 DDCCLK
GPIO Connector
Pin Signal Name Pin Signal Name
1 GPIO1 2 GPIO5
3 GPIO2 4 GPIO6
5 GPIO3 6 GPIO7
7 GPIO4 8 GPIO8
GPIO1
(Pitch: 2.54mm) 9 GND 10 NC
Note: the factory default values for the connector are pin 1, 3, 5 and 7 are for
TTL input while pin 2, 4, 6 and 8 are for TTL output. The voltage range for the
IO signals is 0 ~ 3.3V.