EVOC EC3-1813 Series User manual

EC3-1813 SERIES
基于 Intel Luna Pier 平台 3.5 寸主板
3.5 ″Motherboard Based on Intel Luna Pier
Platform
Version:C00

Announcement
What contained in this User Manual does not represent the commitments of EVOC
Company. EVOC Company reserves the right to revise this User Manual, without
prior notice, and will not be held liable for any direct, indirect, intended or unintended
losses and/or hidden dangers due to installation or improper operation.
Before purchasing, please have a detailed understanding of the product performance
to see whether it meets your requirement.
EVOC is a registered trademark of EVOC Intelligent Technology Co., Ltd. All
trademarks used in this User’s Manual are the property of their respective owners.
EVOC Intelligent Technology Co., Ltd. ©2010, Copyright Reserved. No part of this
manual may be reproduced in any form or by any means, such as in electronic or
mechanical way, without permission from EVOC.
Please visit our website: http://www.evoc.com for more information,
Or please send to the Technical Support Mailbox [e-mail] or
[email protected] for consultation.

Safety Instructions
1. Before handling the product, please read the user’s manual carefully;
2. Any board or card not ready to be installed shall be kept in the anti-static
packaging;
3. Before taking board or card from anti-static packaging, put your hand on
grounded metal object for a while (about 10 seconds) to eliminate static on your
body;
4. While holding a board or card, please do wear static protective gloves; always
hold a board by its edges;
5. Before inserting, removing or re-configuring motherboard or expansion card,
first disconnect the computer and peripherals from their power sources to
prevent electric shock to human bodies or damage to product;
6. Before removing boards or the box PC, disconnect the AC power cord from
power source;
7. For box PC products, when inserting or removing boards, disconnect the
computer and peripherals from the power sources firstly;
8. Before connecting or unplugging any equipment, make sure all power cords are
unplugged in advance;
9. To avoid unnecessary damage caused by turning on/off computer frequently,
wait at least 30 seconds before re-turning on the computer.

Table of Contents
Chapter 1 Product Introduction.....................................................................................1
Overview..................................................................................................................1
Mechanical Dimension, Weight and Environment ...................................................1
Typical Consumption ...............................................................................................2
Microprocessor.........................................................................................................2
Chipset .....................................................................................................................2
System Memory .......................................................................................................2
Display Function ......................................................................................................2
LAN Function ..........................................................................................................3
Audio Function ........................................................................................................3
Power Feature ..........................................................................................................3
Expansion Bus .........................................................................................................3
Watchdog Function ..................................................................................................3
I/O Connector...........................................................................................................3
Chapter 2 Installation....................................................................................................5
Product Outline ........................................................................................................5
Locations of Connectors ..........................................................................................6
Structure...................................................................................................................7
Display Connector....................................................................................................9
LVDS Backlight Control Connector ......................................................................10
Audio Connector ....................................................................................................10
Serial Port...............................................................................................................11

SATA Connector .................................................................................................... 11
Hot-swap of SATA Hard Disk................................................................................12
LAN Port................................................................................................................14
USB Port ................................................................................................................15
2-in-1 Mouse/Keyboard Connector........................................................................15
GPIO Connector.....................................................................................................16
Status Controlling Connector on Front Panel.........................................................16
Power Connector....................................................................................................17
CPU Fan Connector ...............................................................................................17
CF Connector.........................................................................................................18
PCI-104 Bus Expansion Connector........................................................................19
Chapter 3 BIOS Setup ................................................................................................20
BIOS Overview......................................................................................................20
BIOS Parameter Setup ...........................................................................................20
Basic Function Setting for BIOS............................................................................21
Chapter 4 Install the Drivers.......................................................................................38
Appendix ....................................................................................................................39
Watchdog Programming Guide ..............................................................................39
Digital IO Program Guide......................................................................................41
Troubleshooting and Solutions...............................................................................44

Chapter 1 Product Introduction
EC3-1813 SERIES - 1 -
Chapter 1 Product Introduction
Overview
EC3-1813 is an embedded motherboard with low power consumption, which is
developed basing on Intel® Luna Pier Refresh platform and is compliant with 3.5″
single-board specification.
The board adopts Intel®Atom™N450 processor + ICH8M technique solution
on-board. It provides one SO-DIMM DDR2 slot and 1GB DDR2 memory on-board,
up to 2GB. Support VGA, LVDS (18bit) display (Clone or expansion mode); two
10/100/1000Mbps Ethernet controllers (EC3-1813CLDNA only supports one
10/100/1000Mbps Ethernet controller); support PCI-104 bus expansion; four USB2.0
ports; two SATA connectors; one Type I/II CF connector; one HD Audio connector;
four COMs (one of which supports RS-232/ RS-422/ RS-485); one PS/2
keyboard/mouse connector; the board adopts 12V single power supply.
The product adopts Intel® low power consumption solution; the small dimension
design enables the product can be applied in mechanical control, e-police, information
station, medical device and various instrumentation, etc.
Mechanical Dimension, Weight and Environment
Dimension: 129mm (L) × 146.1mm (W) × 28mm (H);
Net Weight: EC3-1813CLD2NA: 195.7g;
EC3-1813CLDNA: 194.7g;
Operating Environment:
Temperature: -20℃~ 60℃;
-20℃~ 70℃(with cooling fan);
Humidity: 5% ~ 95% (non-condensing);

Chapter 1 Product Introduction
- 2 - EC3-1813 SERIES
Storage Environment:
Temperature: -40℃ ~ 80℃;
Humidity: 5% ~ 95% (non-condensing);
Typical Consumption
CPU: on-board Intel® Atom™ N450 1.66GHz
Memory: on-board SAMSUNG 1GB DDR2 667MHz memory + 1GB Apacer DDR2
667MHz memory bank
[email protected]; +5%/-3%;
Microprocessor
On-board Intel® Atom™ N450 CPU with 1.66GHz main frequency; internal integrate
memory controller and graphic controller.
Chipset
Intel® Pineview-M + Intel® ICH8M;
System Memory
Support maximum memory capacity up to 2GB. Wherein, it has 1GB DDR2 memory
on-board and provides one 200 Pin DDR2 memory slot, which supports Un-buffered
and NON-ECC DDR2 667MHz memory bank up to 1GB.
Display Function
Adopt Pineview-M chip integration, which assigns display memory according to
requirement and supports VGA + LVDS dual-display function. CRT supports
maximum resolution up to 1400x1050@60Hz; LVDS supports maximum resolution
up to 1280x800 or 1366x768.

Chapter 1 Product Introduction
EC3-1813 SERIES - 3 -
LAN Function
Provide one 10/100/1000Mbps standard RJ45 LAN port; support Wake-on-LAN
function. In addition, EC3-1813CLD2NA also provides one LAN port educed out via
one 2×7Pin header.
Audio Function
Adopt ALC888 sound effect chip, support MIC-IN, LINE-IN and LINE-OUT
function.
Power Feature
Adopt 4Pin standard power connector, support 12V single power supply.
Expansion Bus
Provide one PCI-104 slot, can expand four PCI Masters.
Watchdog Function
Support 255 levels, programmable by minute or second;
Support watchdog timeout interrupt or reset system.
I/O Connector
Four COMs. COM1 is educed out via DB9 connector and supports Modem
wake-up function; the other three COMs are educed out via 2×5Pin header.
Wherein, COM2 supports RS-232/ RS-422/ RS-485 mode while the other three
only supports RS-232 mode;
One CF card connector;
Two SATA connectors;
One HD Audio connector, educed out via 2×5Pin;
Four USB2.0 ports, USB1 is educed out via connector directly while USB2 is

Chapter 1 Product Introduction
- 4 - EC3-1813 SERIES
educed out via 2×5Pin header;
One PS/2 connector, educed out via 2-in-1 connector;
One 8-bit digital I/O connector, educed out via 2×5Pin header.

Chapter 2 Installation
EC3-1813 SERIES - 5 -
Chapter 2 Installation
Product Outline
H1 H2
H4
H3
H5
H6
H7
Unit: mm
Warning!
Please adopt appropriate screws and proper installation methods (including
board location, CPU and heat sink installation, etc); otherwise, the board may be
damaged. It is recommended to use GB9074.4 M3×6 screws at H1 ~ H7.

Chapter 2 Installation
- 6 - EC3-1813 SERIES
Locations of Connectors
KM1
COM1 VGA1
LAN1 USB1
COM2
COM3 COM4 USB2 GPIO1
JCC1
JP5
JP1
J1
SATA1 SATA2
PWR1
LCDB1
LVDS1
JLCD1
CPUFAN1
FP1
FP3
FP2
LAN2
AUDIO1
JP2
JP3
JP4
JCF1
JP6
DIMM1
H1 H2
H4
H3
H6
H5
H7

Chapter 2 Installation
EC3-1813 SERIES - 7 -
Structure
ICH8M
Pineview M
DMI X4
Controller
Link
Micro-FCBGA8-559
22mmx22mm
32bit sample,192KHz,4 codecs
SODIMM
DDR2 667
supported 1GB
ON Board
X16 1GBit
supported 1GB
DDR2 667
COM2 RS232/RS422/RS485 COM1&COM3&COM4
RS232
82801HBM BGA676
31mmx31mm
spec.1.1
SMBUS9534
8 路 GPIO
TDP 2.4W
TDP N470:6.5W
N450:5.5W
HDA Audio
ALC888
USB X 4 ports 2.0 UHCI/EHCI
AUDIO
PCI2.3 33MHz 4 pairs PCI-104
PCIEX1
RTL8111D
LAN1
PCIEX1
RTL8111D
LAN2
SCH3114
Hardware
Monitor
KB/MOUSE
LPC
SPI
BIOS
TypeI/II CF
spec.2.5
3Gb/s
SATA
SATA X 2 PORTS
ATA33/66/100 PIO/Ultra mode
VGA Max: 1400x1050@60Hz
Analog CRT 200-MHz core render
18 Bit single channel
LVDS Max 1280x800
Tip: How to identify the first pin of the jumpers and connectors
1. Observe the letter beside the socket, it would be marked with “1” or thickened
lines or triangular symbols;
2. Observe the solder pad on the back, the square pad is the first pin;

Chapter 2 Installation
- 8 - EC3-1813 SERIES
1. JCC1: Clear/Keep CMOS Setting (Pin Distance: 2.0 mm)
CMOS is powered by the button battery on board. Clear CMOS will restore original
settings (factory default). The steps are listed as follows: (1) Turn off the computer
and unplug the power cable; (2) Instantly short circuit JCC1; (3) Turn on the
computer; (4) Follow the prompt on screen to enter BIOS setup when booting the
computer, load optimized defaults; (5) Save and exit. Please set as follows:
Setup Function
1-2 Open Normal (Default)
JCC1 1-2 Short Clear the contents of CMOS, all BIOS setting
will restore to factory default values.
2. JLCD1: Select LCD Operating Voltage (Pin Distance: 2.0mm)
Different LCD screens have different voltages; the board provides two voltage
options, 3.3V and 5V. Only when the selected LCD voltage is in accord with the LCD
voltage in use, can the LCD screen display normally. Please set as follows:
Setup Function
1-2 Short +3.3V(Default)
JLCD1 2-3 Short +5V
3. JCF1: Select CF Card Operating Voltage (Pin Distance: 2.0mm)
Different CF cards have different operating voltages; the board provides two voltage
options, 3.3V and 5V. Only when the selected CF card operating voltage is in accord
with the CF card operating voltage in use, can the system stability be ensured. Please
set as follows:
Setup Function
1-2 Short +3.3V
JCF1 2-3 Short +5V(Default)
Note: the CF card voltage selection is set to complying with different CF cards;
as for the CF card with no specified operating voltage, CF card voltage shall be
set according to actual situation.

Chapter 2 Installation
EC3-1813 SERIES - 9 -
4. JP1 ~ JP5 Select Serial Port Mode (Pin Distance: 2.0mm)
Mode Selection
Pin Setting RS-232
(Default) RS-422 RS-485
JP1 1-2 5-6 3-4
JP2 1-2 2-3 2-3
JP3 1-2 2-3 2-3
JP4 1-2 2-3 2-3
JP1
JP2 ~ JP5 JP5 1-2 2-3 2-3
5. JP6: Select VIO Voltage of PCI-104 (Pin Distance: 2.0mm)
The VIO of PCI-104 supplies power for the bus signal of the expansion device;
therefore, the VIO voltage shall be selected according to the connected expansion
device. (Note: the operating voltage of the expanded PCI devices shall be the same).
Setup Function
1-2 Short +3.3V(Default)
JP6 2-3 Short +5V
Display Connector
1) VGA Connector
Pin Signal Name Pin Signal Name
1 Red 2 Green
3 Blue 4 NC
5 GND 6 GND
7 GND 8 GND
9 +5V 10 GND
11 NC 12 DDCDATA
13 HSYNC 14 VSYNC
VGA1
15 DDCCLK

Chapter 2 Installation
- 10 - EC3-1813 SERIES
2) Single-channel 18-bit LVDS Connector
Pin Signal Name Pin Signal Name
1 LVDS_D0+ 2 LVDS_D0-
3 GND 4 GND
5 LVDS_D1+ 6 LVDS_D1-
7 GND 8 GND
9 LVDS_D2+ 10 LVDS_D2-
11 GND 12 GND
13 CLK+ 14 CLK-
15 GND 16 GND
17 NC 18 NC
LVDS1
(Pin Distance: 1.0mm)
19 VDD 20 VDD
LVDS Backlight Control Connector
Pin Signal Name
1 VCC_LCDBKLT
2 NC
3 LCD_BKLTEN
LCDB1 (Pin Distance: 2.0mm)
4 GND
Note: VCC_LCDBKLT---backlight power (the current of the pin shall be limited
below 1A); LCD_BKLTEN --- backlight enabling, active high.
Audio Connector
The board provides one 2×5Pin AUDIO pin header (Pin Distance: 2.0mm).
Pin Signal Name Pin Signal Name
1 LOUT_R 2 LOUT_L
3 GND_AUDIO 4 GND_AUDIO
5 LIN_R 6 LIN_L
7 GND_AUDIO 8 GND_AUDIO
AUDIO1 9 MIC_L 10 MIC_R

Chapter 2 Installation
EC3-1813 SERIES - 11 -
Serial Port
The board provides one super-slim DB9 serial port socket and three 2×5Pin serial
ports (Pin Distance: 2.0mm). COM2 supports RS-232/RS-422/RS-485 mode while the
other three ports support RS-232 modes.
Signal Name
COM1 ~ COM4 COM2
Pin
RS-232 RS-422 RS-485
1 DCD# TXD- Data-
2 RXD TXD+ Data+
3 TXD RXD+ NC
4 DTR# RXD- NC
5 GND GND GND
6 DSR# NC NC
7 RTS# NC NC
8 CTS# NC NC
9 RI# NC NC
COM1
COM2 ~ COM4
10 NA NA NA
Note: under RS-485 mode, the transmission direction for data is controlled
automatically.
SATA Connector
The board provides two standard vertical SATA sockets.
Pin Signal Name
1 GND
2 TX+
3 TX-
4 GND
5 RX-
6 RX+
SATA1/SATA2
7 GND

Chapter 2 Installation
- 12 - EC3-1813 SERIES
Hot-swap of SATA Hard Disk
Notices for hot-swap of SATA hard disk:
1. The hard disk shall support SATA 2.0 and use 15-pin SATA hard disk power
connector.
2. The driver of chipset shall support the hot-swap of SATA hard disk.
3. Hot-swap of SATA hard disk with the operating system is forbidden when system
is power-on.
Please carry out hot plug as follows, improper operation may destroy the hard disk or
result in data lost.
Hot Plug
Step 1: Please plug the 1 x 4 pin SATA power connector (white) into the power adapter.
Step 2: Please connect the SATA data cable to the SATA connector on board.
SATA Data Cable SATA Power Cable

Chapter 2 Installation
EC3-1813 SERIES - 13 -
Step 3: Please connect the 15-pin SATA power connector (black) to the SATA hard
disk.
Step 4: Please connect the SATA data cable to the SATA hard disk.
Hot Unplug
Step 1: Uninstall the hard disk from the device manager.
Step 2: Unplug the data cable from the SATA hard disk.
Step 3: Unplug the SATA 15-pin power connector (black) from the SATA hard disk.

Chapter 2 Installation
- 14 - EC3-1813 SERIES
LAN Port
The board provides one standard 10/100/1000Mbps RJ45 connector.
LAN1
LILED
(Dual Color: O/G)
LAN Speed
Indicator
ACTLED
(Green)
LAN Activity
Indicator
Green 1000Mbps
Blink Data Transmitting Orange 100Mbps
Off No Data to Transmit Off 10Mbps
In addition, EC3-1813CLD2NA also provides one 2×7Pin 10/100/1000Mbps LAN
port, which needs to be fixed on chassis via transfer cable before connecting with
peripherals. The pin definitions are as follows:
Pin Signal Name Pin Signal Name
1 MX0+ 2 MX0-
3 MX1+ 4 MX1-
5 MX2+ 6 MX2-
7 MX3+ 8 MX3-
9 GND 10 GND
11 LINK_LED+
(SPEED1000-) 12 LINK_LED-
(SPEED100-)
LAN2
(Pin Distance: 2.0mm) 13 ACT_LED+ 14 ACT_LED-

Chapter 2 Installation
EC3-1813 SERIES - 15 -
USB Port
The board provides one dual-layer 90-degree A Type USB port with EMI shielding.
Pin Signal Name
1 +5V
2 USB_Data-
3 USB_Data+
USB1
4 GND
The board provides one 2×5 (the 9th Pin is NA) USB port (Pin Distance: 2.0mm).
Pin Signal Name Pin Signal Name
1 +5V 2 +5V
3 USB1_Data- 4 USB2_Data-
5 USB1_Data+ 6 USB2_Data+
7 GND 8 GND
USB2
9 NA 10 GND
2-in-1 Mouse/Keyboard Connector
The board provides one 2-in-1 mouse/keyboard socket.
Pin Signal Name
1 KB_DATA
2 MS_DATA
3 GND
4 +5V
5 KB_CLK
KM1
6 MS_CLK