Exerpeutic 975XBT User manual

OWNER’S MANUAL
IMPORTANT: Read all instructions carefully before using this product.
Retain this owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to
change without notice.
4120.2-080117
RECUMBENT BIKE
GOLD 975XBT
WITH 21 WORKOUT PROGRAMS

PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE.
STOP. Contact customer service if you have any questions
regarding assembly or proper operation of the machine.
Email us at:
[e-mail]
Or call us at:
1-844-641-7921
Hours:
8:00 am to 5:00 pm (PST) Daily

1
TABLE OF CONTENT
SERVICE ------------------------------------------------------------------------ 2
LABEL PLACEMENT --------------------------------------------------------- 3
IMPORTANT SAFETY GUIDELINES ------------------------------------- 4
OVERVIEW DRAWING ---------------------------------------------------- 6
PARTS LIST --------------------------------------------------------------------- 7
HARDWARE & TOOLS PACK -------------------------------------------- 9
REMOVE THE METAL TUBE--------------------------------------------- 10
ASSEMBLY -------------------------------------------------------------------- 11
CONSOLE --------------------------------------------------------------------- 20
ADJUSTMENTS --------------------------------------------------------------- 23
LUBRICATION----------------------------------------------------------------- 24
TROUBLESHOOTING ------------------------------------------------------- 25
TRANSPORT & STORAGE ------------------------------------------------ 27
WARRANTY -------------------------------------------------------------------- 28
PARTS REQUEST FORM--------------------------------------------------- 29

2
SERVICE
IMPORTANT: FOR NORTH AMERICA ONLY
For damaged or defective product, questions, replacement parts or any other service
support, please contact our customer service department by the below methods:
For The Best Service, please Email:
[e-mail]
Response Time: 1-2 Business Days
Emailing us with the information above will be the best method to receive a response during
peak business hours
Website:
www.paradigmhw.com
Toll-Free:
1-844-641-7921
(8:00 AM - 5:00 PM Pacific Standard Time, Daily)
Response time may vary via calling
Please have the following information ready when requesting for service:
Your name
Phone number
Model number
Serial number
Part number
Proof of Purchase
For damaged or defective product please contact our customer service before returning to
the store.
Paradigm Health & Wellness, Inc.
1189 Jellick Ave.
City of Industry, CA 91748, USA

3
LABEL PLACEMENT

4
IMPORTANT SAFETY GUIDELINES
Read all instructions before using the equipment. When using the equipment, basic
precautions should always be followed. WARNING - To reduce the risk of injury to
persons, read and understand the following:
1. Make sure your equipment is correctly assembled before you use it.
2. Be sure all screws, nuts, and bolts are tightened prior to use.
3. Before using this equipment, we recommend doing warm ups and stretching of the major muscle
groups.
4. Only one person should be using the equipment at a time.
5. Never operate this equipment if it is damaged, if it is not working properly, has been dropped, or
damaged. If a problem is encountered contact Customer Service before using the equipment
again.
6. Always use this equipment on a clear and level surface.
7. For household use only.
8. Do not use outdoors or near water.
9. Use this product only for its intended use as described in this manual. Do not use attachments not
recommended by the manufacturer.
10.Do not wear loose clothing when using the equipment.
11.Never drop or insert any object into any opening.
12.If at any time you feel faint, light-headed, or dizziness while operating the equipment, stop
exercising immediately. You should also stop exercising if you are experiencing pain or any
discomfort.
13.For any problems contact customer service. Servicing should be performed by an authorized
service representative. Our contact number is on the service page.
14.DO NOT pedal in reverse.
15.This product requires a minimum of 6 square feet of space for safe operation.
16.ASSEMBLE ALL PARTS AND HARDWARE IN THE ORDER THAT IS SHOWN IN THE
ILLUSTRATIONS
17.Warning:- Risk of Personal Injury - Consult with your personal physician to see if this
exercise equipment is appropriate for you. This is especially important for people with pre-existing
health problems. Do not use this equipment without your physician's approval.
18.Warning:- Risk of Personal Injury –Do not allow children to use this machine.
19.Warning:- Risk of Personal Injury - Keep children under the age of 13 away from the
machine.
20.Warning:- Risk of Personal Injury –Keep body parts, hair, loose clothing, and jewelry
clear of all moving parts.
21.Warning: - Risk of Personal Injury - Do not attempt to service the unit yourself. Discontinue
use and contact customer service.
22.Warning: - To Reduce The Risk Of Personal Injury - Read And Understand All The
Instructions Before Using the Bike.

5
IMPORTANT SAFETY GUIDELINES
Do not use this equipment if you have any of the following conditions or ailments:
Pregnancy
Extreme obesity
Middle ear infection
Hiatus hernia or Ventral hernia
Glaucoma, retinal detachment or conjunctivitis
Use of anticoagulants including Aspirin in high doses.
Spinal injury, Cerebral Sclerosis, or acutely swollen joints
Heart or circulatory disorders for which you are being treated
High blood pressure, Hypertension, Recent stroke or Transient Ischemic attack
Bone weaknesses including Osteoporosis, Unhealed fractures, Modular pins, or surgically implanted
orthopedic supports.
Do not exceed the maximum rated weight (load):
The Maximum Weight Capacity for this product is 310lbs/141kgs.
Retain this owner’s manual and keep the original purchase receipt
for future reference.
SAVE THESE GUIDELINES

6
OVERVIEW DRAWING

7
PARTS LIST
No.
Description
Qty
No.
Description
Qty
1
Main Frame
1
28
Hand Pulse Wire B L=2100mm
1
2
Front Post
1
29
Spring Washer Φ6
10
3
Rear Stabilizer φ60*1.5*580
1
30
Flat Washer φ8*φ16*1.5
12
4
Seat Slide Tube
1
31
Wire Plug φ12.1
2
5
Seat Post
1
32
Knob M16*1.5*20
1
6
Handlebar
1
33
Hex Socket Bolt M6*8
1
7
Front Stabilizer
1
34
Self-Tapping Phillips Screw
ST4.2*6
4
8
Slide Tube Bracket
1
35
Stopper Φ18*8
1
9
Carriage Bolt M8*75
4
36
Rear Stabilizer End Cap
Ф60*1.5
2
10
Curved Washer φ8*φ20*1.5
10
37
Front Post Cover
1
11
Cap Nut M8
10
38
Left Pedal
1
12
Spring Washer Φ8
14
39
Hex Nut 1/2" S15
1
13
Left Pedal Strap
1
40
Hand Pulse Sensor
2
14
Right Pedal
1
41
Foam Grip I Φ30*Φ24*510
2
15
Right Pedal Strap
1
42
Round End Cap
4
16
Hex Bolt M8*15-S6
4
43
Square End Cap
2
17
Middle Console Wire
1
44
Bushing
2
18
Hand Pulse Wire A
2
45
Front Stabilizer End Cap
2
19
AC Adaptor
1
46
Hex Bolt M6*48
2
20
Seat
1
47
Wheel
2
21
Backrest
1
48
Phillips Pan Head Self-Drilling
Screw ST4.2*15
8
22
Flat Washer Φ6*Φ16*1.2
8
49
Self-Tapping Phillips Screw
ST2.9*12
2
23
Console
1
50
Lock Nut M6
2
24
Phillips Screw M5*10
4
51
Hex Nut M6 S10
2
25
Lower Console Wire L=600
1
52
Square Sensor L=300mm
1
26
Philips Screw M6*15
8
53
Cup Holder
1
27
Hex Bolt M8*45
6
54
Left Cover 632*366*84
1

8
PARTS LIST
No.
Description
Qty
No.
Description
Qty
55
Right Cover 632*366*81
1
75
Foam Grip II Φ30*Φ24*160
2
56
Motor
1
77
Power Supply Cable
1
57
Flat Hex Nut 7/8”
2
78
Lower Motor Wire
1
58
Flat Washer II Ф23*Ф34.5*δ2.5
1
79
Crank Cover Φ60*Φ26*6.5
2
59
Bearing Nut II 7/8”
1
80
End Cap
2
60
Ball Bearing
2
81
Hex Nut M8
1
61
Bearing Cup
2
82
Adjustable Leveler
1
62
Bearing Nut I 15/16”
1
83
Self-Tapping Phillips Screw
ST4.2*20
6
63
Flat Washer I Ф24*Ф40*δ3.0
1
84
Hex Bolt M10x20
4
64
Crank
1
85
Spring Washer Φ10
4
65
Belt
1
86
Flat Washer Φ10
4
66
Idle Arm
1
87
Upper Console Wire
1
67
Spring Φ18*56*Φ3.0
1
88
Hand Pulse Wire C
2
68
Hexagon head bolts with non -
standard head M8*18 S5
1
89
Right Nylon Nut
1
69
Pressure Pulley
1
90
Left Nylon Nut
1
70
Lock Nut M8
2
91
Spring Washer Φ20*Φ13*2.0
2
71
Fly Wheel φ230
1
92
Shroud Plug
2
72
Flange Nut M10*1.0*6 S14
2
93
Hand Pulse Wire D
2
73
Eye Bolt M6*36
2
74
Tension Bracket 31*30*δ1.0
2

9
HARDWARE & TOOLS LIST
Silicon Oil 1 Bottle

10
REMOVE THE METAL TUBE
Remove the Metal Tubes from the Main Frame (1) by using 6mm Allen Wrench
provided. Discard the metal tubes and hardware, they will not be used in assembly.
6mm Allen Wrench
1PC
TOOL

11
ASSEMBLY
STEP 1
1a. Insert the Cup Holder (53) into the Main Frame (1). See Figure A.
1b. Front Stabilizer Installation: Lift up the front of the Main Frame (1), and attach the Front
Stabilizer (7) onto the front curve of the Main Frame (1) with two Carriage Bolts (9), two Curve
Washers (10), two Spring Washers (12), and two Cap Nuts (11). Use the Multi Hex Tool with
Phillips Screwdriver to tighten the Cap Nuts (11)until they are firm and secure.
1c. Rear Stabilizer Installation: Lift up the rear of the Main Frame (1), and attach the Rear
Stabilizer (3) onto the rear curve of the Main Frame (1) with two Carriage Bolts (9), two Curve
Washers (10), two Spring Washers (12), and two Cap Nuts (11). Use the Multi Hex Tool with
Phillips Screwdriver to tighten the Cap Nuts (11)until they are firm and secure.
HARDWARE PACK
(9) Carriage Bolt
4 PCS
(10) Curved Washer
4PCS
(11) Cap Nut
4PCS
(12) Spring Washer
4PCS
Multi Hex Tool with Phillips
Screwdriver
1PC
TOOL

12
ASSEMBLY
STEP 2
2a. Installing the Left & Right Pedal Straps to the Pedals: Install the Left Pedal Strap (13) onto
the Left Pedal (38). Install the Right Pedal Strap (15) onto the Right Pedal (14). See Figure B.
2b. Installing the Left Pedal: Insert the threaded shaft of the Left Pedal (38)into the threaded
hole on the Left Crank (64). Turn the pedal shaft by hand in a COUNTER-CLOCKWISE direction
until snug. Install the Left Nylon Nut (90) and Spring Washer (91) onto the protruding thread of
the Left Pedal (38) in a CLOCKWISE direction. After doing so, finish off the tightening of the parts
in the same direction as instructed with the Multi Hex Tool with Phillips Screwdriver and Open
Wrench provided.
2c. Installing the Right Pedal: Insert the threaded shaft of the Right Pedal (14) into the threaded
hole on the Right Crank (64). Turn the pedal shaft by hand in a CLOCKWISE direction until snug.
Install the Right Nylon Nut (89) and Spring Washer (91) onto the protruding thread of the Right
Pedal (14) in a COUNTER-CLOCKWISE direction. After doing so, finish off the tightening of the
parts in the same direction as instructed with the Multi Hex Tool with Phillips Screwdriver and
Open Wrench provided.
Open Wrench
1PC
TOOL
Right
Left
Multi Hex Tool with Phillips
Screwdriver
1PC
The Cranks, Pedal Straps, Pedal Shafts, and Foot Pedals
are marked “R” for Right and “L” for Left.

13
ASSEMBLY
STEP 3
3a. Removal of Hardware for Installation: Remove four Hex Bolts (16), four Spring Washers
(12) and four Curved Washers (10) from the Main Frame (1). Slide the Front Post Cover (37)
onto the Front Post (2) before going onto the next sub step.
3b. Connecting the Pulse and Console Wires: Connect the Upper Console Wire (17) from the
Front Post (2) to the Lower Console Wire (25) from the Main Frame (1). Connect the Extension
Hand Pulse Wire A (18) from the Front Post (2) to the Hand Pulse Wire B (28) from the Main
Frame (1). See Figure C.
3c. Installing the Front Post to the Main Frame: Slide the Front Post (2) onto the Main Frame
(1). Align the holes of the Front Post (2) and Main Frame (1). Fasten the Front Post (2) to the
Main Frame (1) with the previously removed four Hex Bolts (16), four Spring Washers (12) and
four Curved Washers (10). Then tighten all the Bolts (16) by using the 6mm Allen Wrench
provided.
6mm Allen Wrench
1PC
TOOL
1
Figure C

14
ASSEMBLY
STEP 4
4a. Removal of Hardware for Installation: Remove four Hex Bolts (84), four Spring Washers
(85)and four Flat Washers (86) from the Seat Post (5).
4b. Installing the Seat Post to the Main Frame: Attach the Seat Post (5) inside the brackets of
the Slide Tube Bracket (8) with four Hex Bolts (84), four Spring Washers (85)and four Flat
Washers (86). Tighten all the Bolts with the 6mm Allen Wrench provided.
PRE-INSTALLED HARDWARE
(84) Hex Bolt
4PCS
(85) Spring
Washer
4PCS
(86) Flat
Washer
4PCS
6mm Allen Wrench
1PC
TOOL

15
ASSEMBLY
STEP 5
5a. Removal of Hardware for Installation: Remove four Phillips Screws (26), four Spring
Washers (29), and four Flat Washers (22) from the underside of the Seat (20).
5b. Installing the Seat to the Main Frame: Align the holes of the Seat (20)to the holes of the Seat
Post (5). Secure the Seat (20) with the previously removed four Phillips Screws (26), four Spring
Washers (29) and four Flat Washers (22). Tighten the Phillips Screws (26) using the Multi Hex
Tool with the Phillips Screwdriver provided.
PRE-INSTALLED HARDWARE
(26) Phillips
Screw
4PCS
(29) Spring
Washers
4PCS
(22) Flat
Washer
4PCS
Multi Hex Tool with Phillips
Screwdriver
1PC
TOOL

16
ASSEMBLY
STEP 6
6a. Removal of Hardware for Installation: Remove four Phillips Screws (26), four Spring
Washers (29) and the four Flat Washers (22)from the Backrest (21) with the Multi-Hex Tool
with Phillips Screwdriver.
6b. Installing the Backrest: Align the holes of the Backrest (21)to the holes of the Seat Post (5).
Secure the Backrest (21) with four Phillips Screws (26), four Spring Washers (29) and four Flat
Washers (22). Tighten the Phillips Screws (26) using the Multi Hex Tool with Phillips
Screwdriver provided.
Multi Hex Tool with Phillips
Screwdriver
1PC
TOOL
PRE-INSTALLED HARDWARE
(26) Phillips
Screw
4PCS
(29) Spring
Washers
4PCS
(22) Flat
Washer
4PCS

17
ASSEMBLY
STEP 7
7a. Installing the Handlebar: Attach the Handlebar (6) onto the Seat Post (5) with two Hex Bolts
(27), two Curved Washers (10), two Flat Washers (30), two Spring Washers (12) and two Cap
Nuts (11).
7b. Connecting the Pulse Wires: Connect the Hand Pulse Wires D (93) from the Handlebar (6)
to the Hand Pulse Wire B (28) from the Main Frame (1).
HARDWARE PACK
(27) Hex Bolt
2PCS
(12) Spring Washer
2PCS
(30) Flat Washer
2PCS
(11) Cap Nut
2PCS
(10) Curved Washer
2PCS
Multi Hex Tool with Phillips
Screwdriver
1PC
TOOL

18
ASSEMBLY
Step 8
8a. Removal of Hardware for Installation: Remove four Phillips Screws (24) from the Console
(23).
8b. Connecting the Console Wires: Connect the Lower Console Wire (17) from the Front Post
(2) to the Upper Console Wire (87) from the Console (23). Connect the Hand Pulse Wire A (18)
coming from the Front Post (2) to the Hand Pulse Wires C (88) coming from the Console (23).
See Figure D.
8c. Installing the Console: Attach the Console (23) onto the Front Post (2), and tighten the four
Phillips Screws (24) with the Multi Hex Tool with Phillips Screwdriver provided.
WARNING: This Console Is Not Battery Operated. Use The Adaptor Provided To Power The
Console. See Step 9.
Multi Hex Tool with Phillips
Screwdriver
1PC
TOOL