Extraflame ANASTASIA PLUS User manual

MADE IN ITALY
design & production
anastasia plus
UK pellet stoves useR Manual
004276501 - Rev 009
Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per La Nordica
Anastasia Plus o cerca il tuo prodotto tra le migliori offerte di Stufe, Camini e Riscaldamento

ENGLISH2

ENGLISH
ENGLISH.................................................................................................................................................................................................4
WarNINGS........................................................................................................................................................................................................ 4
SafEty.............................................................................................................................................................................................................. 4
routINE MaINtENaNcE................................................................................................................................................................................ 5
INStaLLatIoN.................................................................................................................................................................................................. 6
General........................................................................................................................................................................................................................................................6
PELLEtS aNd fEEdING ................................................................................................................................................................................... 8
dEtaILS of aNaStaSIa PLuS........................................................................................................................................................................ 9
radio/emerGency Board..................................................................................................................................................................................................................9
rearminG.....................................................................................................................................................................................................................................................9
ductING fEaturES ...................................................................................................................................................................................... 10
factory dEfauLt ductING oPEratIoN.................................................................................................................................................. 10
ductING oPEratIoN WItH tHErMoStat or ProBE (oPtIoNaL) ....................................................................................................... 10
ta SuPPLEMENtary tHErMoStat (oPtIoNaL) ...................................................................................................................................... 11
rearminG...................................................................................................................................................................................................................................................11
Fuse...............................................................................................................................................................................................................................................................11
HaNdHELd ..................................................................................................................................................................................................... 12
conFiGuraTion......................................................................................................................................................................................................................................12
BaTTery Type and replacemenT.................................................................................................................................................................................................12
HaNdHELd fEaturES .................................................................................................................................................................................. 13
dISPLay .......................................................................................................................................................................................................... 14
GENEraL MENu ............................................................................................................................................................................................. 15
Basic insTrucTions ............................................................................................................................................................................................................................15
coMMISSIoNING SEttINGS......................................................................................................................................................................... 16
daTe and Time seTTinGs ..................................................................................................................................................................................................................16
lanGuaGe seTTinG...............................................................................................................................................................................................................................16
oPEratIoN aNd LoGIc................................................................................................................................................................................ 17
uSEr MENu..................................................................................................................................................................................................... 18
pelleTs........................................................................................................................................................................................................................................................18
V1 - Fan ........................................................................................................................................................................................................................................................18
reseT.............................................................................................................................................................................................................................................................18
SEt cHroNo .................................................................................................................................................................................................. 19
enaBle chrono.....................................................................................................................................................................................................................................19
seT prG 1-4.................................................................................................................................................................................................................................................19
ductING......................................................................................................................................................................................................... 20
SEttINGS ........................................................................................................................................................................................................ 20
seT clock...................................................................................................................................................................................................................................................20
lanGuaGe..................................................................................................................................................................................................................................................20
display........................................................................................................................................................................................................................................................21
sTand-By ....................................................................................................................................................................................................................................................21
delTa T .........................................................................................................................................................................................................................................................22
addItIoNaL fuNctIoNS............................................................................................................................................................................. 22
comForT....................................................................................................................................................................................................................................................22
handheld room sensor caliBraTion....................................................................................................................................................................................22
cLEaNING aNd MaINtENaNcE................................................................................................................................................................... 23
MaINtENaNcE............................................................................................................................................................................................... 23
cleaninG and mainTenance By The user.............................................................................................................................................................................23
routINE MaINtENaNcE carrIEd out By autHorISEd tEcHNIcIaNS ............................................................................................. 27
puTTinG The eQuipmenT ouT oF serVice (end oF The season).................................................................................................................................27
dISPLayS ........................................................................................................................................................................................................ 30
aLarMS .......................................................................................................................................................................................................... 31
GuaraNtEE tErMS ...................................................................................................................................................................................... 32
attENtIoN
SurfacES caN BEcoME VEry Hot!
aLWayS uSE ProtEctIVE GLoVES!
During combustion, thermal energy is released that signicantly increases the heat of surfaces, doors, handles, controls, glass, exhaust
pipes, and even the front of the appliance. Avoid contact with those elements if not wearing protective clothing (protective gloves
included). Make sure children are aware of the danger and keep them away from the stove during operation.
3

ENGLISH
Warnings
This instructions manual is an integral part of the product: make sure that it always accompanies the
appliance, even if transferred to another owner or user, or if transferred to another place. If it is damaged
or lost, request another copy from the area technician. This product is intended for the use for which it has
been expressly designed. The manufacturer is exempt from any liability, contractual and extracontractual,
for injury/damage caused to persons/animals and objects, due to installation, adjustment and maintenance
errors and improper use.
Installation must be performed by qualied sta, which assumes complete responsibility for the
denitive installation and consequent good functioning of the product installed. One must also bear
in mind all laws and national, regional, provincial and town council Standards present in the country in
which the appliance has been installed, as well as the instructions contained in this manual.
The Manufacturer cannot be held responsible for the failure to comply with such precautions.
After removing the packaging, ensure that the content is intact and complete. Otherwise, contact the
dealer where the appliance was purchased.
All electric components that make up the product must be replaced with original spare parts exclusively
by an authorised after-sales centre, thus guaranteeing correct functioning.
safety
THE APPLIANCE MAY BE USED BY CHILDREN 8 YEARS OF AGE OR OLDER AND INDIVIDUALS
WITH REDUCED PHYSICAL, SENSORY, OR MENTAL CAPACITIES OR WITHOUT EXPERIENCE OR
THE NECESSARY KNOWLEDGE, PROVIDED THAT THEY ARE SUPERVISED OR HAVE RECEIVED
INSTRUCTIONS ON SAFE USE OF THE APPLIANCE AND THAT THEY UNDERSTAND THE INHERENT
DANGERS.
THE GENERATOR MUST NOT BE USED BY PERSONS (INCLUDING CHILDREN) WITH REDUCED
PHYSICAL, SENSORY AND MENTAL CAPACITIES OR WHO ARE UNSKILLED PERSONS, UNLESS THEY
ARE SUPERVISED AND TRAINED REGARDING USE OF THE APPLIANCE BY A PERSON RESPONSIBLE
FOR THEIR SAFETY.
THE CLEANING AND MAINTENANCE REQUIRED BY THE USER MUST NOT BE PERFORMED BY
CHILDREN WITHOUT SUPERVISION.
CHILDREN MUST BE CHECKED TO ENSURE THAT THEY DO NOT PLAY WITH THE APPLIANCE.
DO NOT TOUCH THE GENERATOR WHEN YOU ARE BAREFOOT OR WHEN PARTS OF THE BODY
ARE WET OR DAMP.
THESAFETYANDADjUSTMENTDEVICESMUSTNOTBEMODIFIEDWITHOUTTHEAUTHORISATION
OR INDICATIONS OF THE MANUFACTURER.
DO NOT PULL, REMOVE, TWIST THE ELECTRICAL CABLES COMING OUT OF THE PRODUCT EVEN
IF IT IS DISCONNECTED FROM THE MAINS.
IT IS ADVISED TO POSITION THE POWER SUPPLY CABLE SO THAT IT DOES NOT COME INTO
CONTACT WITH HOT PARTS OF THE APPLIANCE.
THE POWER SUPPLY PLUG MUST BE ACCESSIBLE AFTER INSTALLATION.
DO NOT CLOSE OR REDUCE THE DIMENSIONS OF THE AIRING VENTS IN THE PLACE OF
INSTALLATION. THE AIRING VENTS ARE ESSENTIAL FOR CORRECT COMBUSTION.
We thank you for having chosen our company; our product is a great heating solution developed from the
most advanced technology with top quality machining and modern design, aimed at making you enjoy
the fantastic sensation that the heat of a ame gives, in complete safety.
4

ENGLISH
DO NOT LEAVE THE PACKAGING ELEMENTS WITHIN REACH OF CHILDREN OR UNASSISTED
DISABLED PERSONS.
THE HEARTH DOOR MUST ALWAYS BE CLOSED DURING NORMAL FUNCTIONING OF THE
PRODUCT.
WHEN THE APPLIANCE IS FUNCTIONING AND HOT TO THE TOUCH, ESPECIALLY ALL EXTERNAL
SURFACES, ATTENTION MUST BE PAID
CHECK FOR THE PRESENCE OF ANY OBSTRUCTIONS BEFORE SWITCHING THE APPLIANCE ON
FOLLOWING A PROLONGED PERIOD OF INACTIVITY.
THE GENERATOR HAS BEEN DESIGNED TO FUNCTION IN ANY CLIMATIC CONDITION. IN
PARTICULARLY ADVERSE CONDITIONS (STRONG WIND, FREEzING) SAFETY SYSTEMS MAY
INTERVENETHAT SWITCHTHE GENERATOR OFF. IFTHIS OCCURS, CONTACTTHE TECHNICAL AFTER-
SALES SERVICE AND ALWAYS DISABLE THE SAFETY SYSTEMS.
IN THE EVENT THE FLUE CATCHES FIRE, USE SUITABLE SYSTEMS FOR SUFFOCATING THE FLAMES
OR REQUEST HELP FROM THE FIRE BRIGADE.
THIS APPLIANCE MUST NOT BE USED TO BURN WASTE
DO NOT USE ANY FLAMMABLE LIQUIDS FOR IGNITION
DURING THE FILLING PHASE DO NOT PUT THE BAG OF PELLETS TO INTO CONTACT WITH THE
PRODUCT
THE MAjOLICAS ARE TOP QUALITY ARTISAN PRODUCTS AND AS SUCH CAN HAVE MICRO-DOTS,
CRACKLES AND CHROMATIC IMPERFECTIONS. THESE FEATURES HIGHLIGHT THEIR VALUABLE
NATURE. DUE TO THEIR DIFFERENT DILATION COEFFICIENT, THEY PRODUCE CRACKLING, WHICH
DEMONSTRATETHEIR EFFECTIVE AUTHENTICITY. TO CLEANTHE MAjOLICAS, IT IS RECOMMENDED
TO USE A SOFT, DRY CLOTH. IF A DETERGENT OR LIQUID IS USED, THE LATTER COULD PENETRATE
INSIDE THE CRACKLES, HIGHLIGHTING THEM.
routine Maintenance
Based on Decree 22 January 2008 n°37 art.2, routine maintenance means interventions aimed at reducing
degradation due to normal use, as well as dealing with accidental events entailing the need of rst
interventions, which however do not modify the structure of the system upon which one is intervening or
its intended use according to the requirements laid down by the technical standards in force and by the
manufacturer's use and maintenance manual.
5

A
C
B
ENGLISH
Air inlet
REFERENCES INFLAMMABLE OBJECTS NONINFLAMMABLE OBJECTS
A 200 mm 100 mm
B 1500 mm 750 mm
C 200 mm 100 mm oor protection
InstallIng Inserts
When installing inserts, access must be prevented to the internal parts of the appliance and it must not be possible to access live parts during
extraction operations.
Any wiring, for example the power cable or room probe, must be positioned so as not to be damaged during movement of the insert and
must not come into contact with hot parts.
VentIlatIon and aeratIon of the InstallatIon premIses
Ventilation is deemed sucient when the room is equipped with air inlets according to the table:
Appliance categories Reference standard
Percentage of the
net opening section with respect to the
appliance fumes outlet section
Minimum net opening value of the
ventilation duct
Pellet stoves UNI EN 14785 - 80 cm²
Boilers UNI EN 303-5 50% 100 cm²
In any case ventilation is deemed sucient when the pressure dierence between the external and internal environment is equal to or less
than 4 Pa.
InstallatIon
general
The ue gas exhaust and hydraulic connections must be carried out by qualied personnel who must issue installation conformity
documentation compliant with national standards.
The installer must provide the owner or person acting for him, according to the legislation in force, with the declaration of conformity,
supplied with:
1) the use and maintenance manual of the appliance and of the system components (such as for example, the smoke ducts, chimney, etc.);
2) photocopy or photograph of the chimney plaque;
3) system booklet (where applicable).
The installer must ask to be issued with a receipt stating that the documentation has been provided, and must keep it with a copy of the technical
documentation relating to the installation.
For installation in a condominium, prior approval from the condominium's administrator must be requested.
Where required, check the exhaust gas emissions after installation. Should a sampling point be installed, it must be airtight.
CompatIBIlItY
Installation in premises with re hazards is forbidden. Installation in residential premises (except for sealed operation appliances) is also forbidden:
in which there are liquid fuel-operated appliances with continuous or intermittent operation, which draw the combustion air in the
room in which they are installed, or
in which there are type B gas appliances intended for room heating, with or without production of domestic hot water and in adjacent
and adjoining premises, or
in which, in any case, the depression measured during installation between the internal and external environment is greater than 4 Pa
InstallatIons In Bathrooms, Bedrooms and studIo flats
Installation in bathrooms, bedrooms and studio ats is only allowed for sealed or closed hearth appliances with ducted combustion air taken
from the outside.
posItIonIng and safetY dIstanCes
The support surfaces and/or points must have a suitable capacity to bear the overall weight
of the appliance, accessories and coverings.
If the oor is made of a combustible material,
we recommending using a non-combustible material to protect the front part from any
burnt material which might fall during routine cleaning operations.
The generator must be level to function properly.
The adjacent, side and rear walls and the supporting surface must be made of non-
combustible material. Installation adjacent to combustible or heat sensitive materials is
allowed as long as there is a suitable safety distance in between, which for pellet stoves is:
6

3 - 5%
Max 3 mt
ENGLISH
EXAMPLES OF CORRECT CONNECTION TO THE CHIMNEY
In the presence of type B gas appliances with intermittent operation not intended for heating, they must have their own aeration and/or
ventilation opening.
The air inlets must meet the following requirements:
they must be protected with grids, metal mesh, etc., but without reducing the net useful section;
they must be made so as to make the maintenance operations possible;
positioned so that they cannot be obstructed;
The clean and non-contaminated air ow can also be obtained from a room adjacent to that of installation (indirect aeration and
ventilation), as long as the ow takes place freely through permanent openings communicating with the outside.
The adjacent room cannot be used as a garage, or to store combustible material or for any other activity with a re hazard, bathroom,
bedroom or common room of the building.
flue gas eXhaust
The heat generator works in depression and is equipped with an outlet fan for ue gas extraction. There must be a single exhaust system for
the generator. Using a ue that is shared with other devices is not allowed.
The components of the ue gas exhaust system must be chosen in relation to the type of appliance to be installed in compliance with:
UNI/ TS 11278 in the event of metal chimneys, with particular attention to that stated in the specication;
UNI EN 13063-1 and UNI EN 13063-2, UNI EN 1457, UNI EN 1806 in the event of non-metallic chimneys.
The length of the horizontal section must be minimal and, in any case, no longer than 3 metres, with a minimum upward slope of 3%
There must not be more than 4 direction changes including the one due to the use of the "T" element.
A“T” tting with a condensation collection cap must be provided at the base of the vertical section.
If the exhaust is not inserted in an existing ue, a vertical section with a windproof end piece is required (UNI 10683).
The vertical duct can be inside or outside the building. If the smoke duct is inserted in an existing ue, it must be certied for solid fuel.
If the smoke duct is outside the building, it must always be insulated.
The smoke ducts must have at least one airtight inlet for ue gas sampling.
All the sections of the ue gas duct must be accessible to inspection.
Inspection openings must be provided for cleaning.
If the generator has a fume temperature lower than 160°C+ ambient temperature caused by the high yield (contact technicians) it
MUST be resistant to humidity.
ChImneY Cap
The chimney caps must meet the following requirements:
they must have a useful outlet section no less than double that of the chimney/ducted system on which it is installed;
they must be adapted in order to prevent the penetration of rain and snow in the chimney/ducted system;
they must be built so that, in the event of winds coming from all directions and from any angle, the expulsion of combustion products
is in any case ensured;
Protection from rain
and wind
Condensation-
proof "T" tting with
inspection plug
Insulated ue
Insulated "T"
tting with
inspection plug
Protection from rain and wind
"T" tting with
inspection
plug
ConneCtIon to the maIns eleCtrIC supplY
The generator is supplied with an electric power cable to be plugged into a 230V 50 Hz socket, possibly with a circuit breaker switch. The
socket must be easily accessible.
The electrical system must be compliant with standards. The eciency of the earthing circuit must be checked. Unsuitable earthing of the
system can cause malfunctioning for which the manufacturer will not be held liable.
Power supply variations beyond 10% can cause faulty operation of the product.
7

ENGLISH
PELLETS AND FEEDING
Pellets are made by applying high pressure to sawdust, or wood waste products (not containing paint) from sawmills, carpentry and other
activities related to processing and working with wood. Given that it does not use any glue to hold it together this type of fuel is completely
environmentally friendly. In fact the compactness of the pellets over time is guaranteed by a natural substance found in the wood itself: wood
coal. In addition to being an environmentally friendly fuel in that it pushes wood residues to the limits pellets also have technical advantages.
While wood has a caloric value of 4.4kWh/kg. (with 15% humidity after around 18 months of seasoning) the caloric value of pellets is 5 kWh/
kg. Pellet density is 650kg/m3 and the water content is equal to 8% of its weight. For this reason they do not require seasoning in order to
arrive at a suciently adequate degree of heat yield.
THE USE OF EXPIRED PELLETS OR ANY OTHER MATERIAL WILL AFFECT THE FUNCTIONALITY OF YOUR
GENERATOR AND MAY LEAD TO THE TERMINATION OF THE WARRANTY AND CESSATION OF ANY ACCOMPANYING
RESPONSIBILITY ON THE PART OF THE MANUFACTURER
The pellets used must comply with the characteristics described by the
following standards:
EN PLUS  UNI EN 14961  2 UNI EN ISO 172252 class A1
 A2
The manufacturer always recommended using pellets with a diameter
of 6 mm with its products.
PELLET STORAGE
In order to ensure problem-free combustion pellets must be stored in
a dry place.
Open the tank lid and load the pellets using a scoop.
8

ON/OFF
L1
L2
L3
L4
L5
P1
P2
P3
ENGLISH
DETAILS OF ANASTASIA PLUS
Combustive air
input
Flue gas exhaust
REARMING
Power supply and fuse
Z1 ducting
Radio/emergency board
Z2 ducting
External thermostat connection
RADIO/EMERGENCY BOARD
The stove is tted with an emergency radio board located in the rear part, allowing the basic operation of the stove in the event the handheld
device is damaged or malfunctions.
The functions that can be managed from the emergency board are:
Serial input
- -
L1 : Yellow led Led o: radio communication not available.
Led on: radio communication available. -
L2 : Red led Led o: normal operation.
Led on: alarm present. -
L3 : Green led
Led o: stove o.
Led on: stove on.
Flashing led: stove in cleaning phase.
P1: On/o stove.
L4 : Yellow led Led on: stove operates at 5th power level. P2: 5th power level setting.
L5 : Yellow led Led on: stove operates at 1st power level. P3: 1st power level setting.
(rear view of stove)
9

T
A
ENGLISH
DUCTING FEATURES
The ANASTASIA PLUS model is tted with two independent ducting outlets.
Ducts Z1 - Z2 are activated by default.
Features:
diameter of ducting outlet: 2x80 mm
maximum recommended ducting length 8m
temperature controlled ducting
regulation of air ow speed as a percentage
independent ducting that can be activated/deactivated (ONOFF)
Z2 ducting
Z1 ducting
FACTORY DEFAULT DUCTING OPERATION
Ducting Z1 and Z2 are always in request by default (bridges on Z1 and Z2) and follow the stove settings.
- No settings necessary.
Z1 MODE set to ON:
Set the SET ZONE Z1 to OFF.
• Until the desired temperature is reached (closed contact) the ducting motor will follow
the stove settings.
• When the temperature set on the thermostat is reached (open contact), the ducting
motor will switch to the 1st speed.
Z1 MODE set to ECO:
Set the SET ZONE Z1 to OFF.
• Until the desired temperature is reached (closed contact) the ducting motor will follow
the stove settings.
• When the temperature set on the thermostat is reached (open contact), the ducting motor
will turn o, and then turn on again when required.
Same SettingS for Z2 ducting
DUCTING OPERATION WITH THERMOSTAT OR PROBE OPTIONAL
The stove is tted with two independent motors for ducting. The connection of an external thermostat or temperature probe (NTC 10K) in
inputs Z1 and Z2, located in the rear part of the stove, makes it possible to control the ducting motor independently of the stove.
Suce it to connect the thermostat/temperature probe and set the desired temperature.
For information on ducting settings see chapter:" menu - ducting"
WITH ROOM THERMOSTAT OPTIONAL
Remove the bridge on Z1 and attach the room thermostat in the room where you wish to control the temperature through Z1 ducting.
Two operating modes:
10

T
A
T
A
ENGLISH
REARMING
If a fuse blows, it is recommended to contact a qualied technician
to check the cause.
FUSE
If there is no power supply to the stove, check the state of the fuse
located in the box between the stove switch and the power cable
connection.
TA SUPPLEMENTARY THERMOSTAT OPTIONAL
The appliance is able to control the room temperature through a supplementary thermostat (optional).
After ignition (by pressing key 1 or through the chrono mode), the stove will work to reach the temperature set on the thermostat, displaying
WORK (closed contact). The room probe incorporated into the handheld device is automatically ignored,
INSTALLATION MUST BE PERFORMED BY QUALIFIED STAFF AND/OR THE MANUFACTURER'S AFTERSALES
TECHNICIANS.
Z1 MODE set to "ON":
Set the desired temperature on the SET
ZONE Z1 (from 07  40°C).
• Until the desired temperature is reached the ducting motor will follow the stove settings.
• When the temperature set on set zone z1 is reached, the ducting motor will switch to
the 1st speed.
Z1 MODE on ECO:
Set the desired temperature on the SET
ZONE Z1 (from 07  40°C).
• Until the desired temperature is reached the ducting motor will follow the stove settings.
• When the temperature set on set zone z1 is reached, the ducting motor will turn o, and
then turn on again when required.
Same SettingS for Z2 ducting
WITH PROBE NTC 10K
Remove the bridge on Z1 and attach the NTC probe in the room where you wish to control the temperature through Z1 ducting.
Two operating modes:
TO INSTALL AND ACTIVATE:
A mechanical or digital thermostat is required.
Remove the plug from the socket.
Using the gure to the side as a reference, connect the two thermostat cables (clean contact - no
220 V!) onto the relative terminals located on the back of the appliance, one red and the other
black.
Connect the power to the stove again.
Press the key (
OK
), and set temperature is set to LOW-TA.
The stove is now correctly congured.
It will work by checking the supplementary external thermostat, based on the TA function (see TA
chapter).
11

ENGLISH
BATTERY TYPE AND REPLACEMENT
To insert/replace the batteries, suce it to remove the battery protection cover at the back of the handheld (gure 1).
Insert the batteries in accordance with the symbols imprinted on the handheld and on the battery itself.
Three AAA batteries are required for the handheld to function.
CONFIGURATION
HANDHELD CODING PROCEDURE:
1. Disconnect the power supply to the stove.
2. Press keys
OK
and
OK
at the same time until the UNIT selection screen appears.
3. Using keys
OK
and
OK
select the new UNIT.
4. Power the stove. Conrm the selected unit within 10 seconds (all leds ash on the radio/emergency card) by pressing the OK key on
the handheld.
5. All leds on the radio/emergency card will remain on for 2 seconds to conrm the new conguration.
6. If the conguration was unsuccessful, the display will read "APPLIANCE NOT FOUND". In this case, repeat the procedure.
J
THE HANDHELD IS ALREADY CONFIGURED WITH "UNIT 0", IN THE EVENT THERE IS ANOTHER STOVE. TO AVOID
INTERFERENCES, A NEW CONFIGURATION MUST BE PERFORMED, MODIFYING ONE OF THE TWO STOVES.
SOME RADIOFREQUENCY DEVICES E.G. MOBILE PHONES, ETC... MAY CAUSE INTERFERENCE WITH
COMMUNICATION BETWEEN THE HANDHELD AND THE STOVE.
Respect the environment!
Used batteries contain metals that are harmful to the environment, and therefore must be disposed of separately in
special containers.
HANDHELD
(gure 1)
12

2
3
1
4
5
6
7
8
ENGLISH
HANDHELD FEATURES
1. Display
2. Set power / scroll across in menus / increase - select a setting
3. Set room / scroll across in menus / reduce - deselect a setting
4. Back key
5. Key to access MENU and CONFIRM
6. On/o stove or restore from sleep mode.
7. -
8. Battery compartment
The handheld is tted with an LCD backlit display. The display remains lit for 5 seconds. After a certain period of time, in order to minimise
battery consumption, the display turns o (sleep mode).
It turns on again after pressing the ON/OFF key (6).
CAUTION!
Do not place the handheld in direct or indirect contact with water. The handheld may not work properly in the presence of humidity or
if exposed to water.
FREQUENCY BANDS MAXIMUM POWER TRANSMITTED
868,3 MHZ 4 mW ERP
869,85MHZ 4 mW ERP
13

22.5
Z1 Z2 STBY 10:50
°C
.
.
LOW
TA
10:50
ALL DEPR
10:50
OFF
ENGLISH
DISPLAY
TIME
TEMPERATURE DETECTED
IN ROOM
CHRONO
STANDBY ACTIVE
Z1  Z2 ACTIVE
ROOM TEMPERATURE
IN REQUEST
ALARM/ERROR PRESENT
NO IGNITION
IDENTIFICATION OF
ALARM/ERROR
INDICATES CONTACT
OF EXTERNAL
SUPPLEMENTARY
THERMOSTAT
COMFORT ACTIVE
LOW BATTERY
14

ENGLISH
GENERAL MENU
KEY FUNCTION
OK
OK
Scroll parameters
Modify settings
OK
On - o key
KEY FUNCTION
Back - exit key
OK
Menu access key
USER MENU % PELLETS
% V1 FAN
RESET
SET CHRONO ENABLE CHRONO
SET PRG1
SET PRG2
SET PRG3
DUCTING Z1 MODE SET PRG4
SET ZONE Z1
Z1 FAN %
Z2 MODE
SETTINGS SET CLOCK SET ZONE Z2
LANGUAGE Z2 FAN %
DISPLAY
STANDBY
DELTA T
*STOVE STATUS
*TECHNICAL
MENU
*TECHNICIANS ONLY
BASIC INSTRUCTIONS
The following recommendations must be followed the rst times the
stove is ignited:
It is possible that slight odours are produced due to the drying
of the paints and silicone used. Do not remain in the room for long
periods.
Do not touch the surfaces as they could still be unstable.
Ventilate the room well several times.
The hardening of surfaces will stop after several heating cycles.
This appliance must not be used to burn waste.
Before lighting the stove, the following points must be checked:
The hydraulic system must be completed in compliance with
regulatory guidelines and the instructions in the manual.
The tank must be full of pellets
The combustion chamber must be clean
The burn pot must be completely free and clean
Check the hermetic closure of the re door and the ash drawer
Check that the power cable is properly connected
The bipolar switch in the rear right part must be positioned on
1.
15

ENGLISH
COMMISSIONING SETTINGS
Once the power cable at the back of the generator has been connected, move the switch, also located on the back, to (I).
The switch at the back of the generator powers the generator board.
The generator remains o and a rst screen appears on the panel reading OFF.
LINE FREQUENCY 50/ 60HZ
If the generator is installed in a country with a frequency of 60Hz, the generator will display "incorrect line frequency". In this case, adjust the
frequency to 60Hz.
SETTINGS SET CLOCK xx:xx - dd/mm/yy Date and time setting
LANGUAGE ita-ing-fra-ted-spa Language setting
DATE AND TIME SETTINGS
This menu allows the date and time to be set.
LANGUAGE SETTING
This menu allows the preferred language to be selected.
SETTINGS SET CLOCK xx:xx - dd/mm/yy Date and time setting
LANGUAGE ita-ing-fra-ted-spa Language setting
J
NO IGNITION
THE APPLIANCE MAY FAIL TO LIGHT BECAUSE THE AUGER IS EMPTY AND NOT ALWAYS ABLE TO LOAD THE BURN POT
WITH THE NECESSARY QUANTITY OF PELLETS IN TIME TO REGULARLY IGNITE THE FLAME.
IF THE PROBLEM OCCURS AFTER ONLY A FEW MONTHS OF OPERATION, CHECK THAT THE ROUTINE CLEANING
DESCRIBED IN THE STOVE BOOKLET HAS BEEN CARRIED OUT CORRECTLY.
DO NOT USE ANY TYPE OF FLAMMABLE LIQUIDS FOR IGNITION!
DO NOT ALLOW THE BAG OF PELLETS TO COME INTO CONTACT WITH THE BOILING HOT STOVE DURING THE
FILLING PHASE!
IN THE EVENT OF CONTINUED FAILURE TO LIGHT, CONTACT AN AUTHORISED TECHNICIAN.
IT IS PROHIBITED TO USE THE APPLIANCE WITHOUT THE PARTITION
AND/OR FLAME GUARD SEE FIGURE ON SIDE.
REMOVAL WILL COMPROMISE THE SAFETY OF THE PRODUCT AND
RESULT IN THE IMMEDIATE NULLIFICATION OF THE WARRANTY
PERIOD.
IN THE EVENT OF WEAR OR DETERIORATION, REQUEST THE PART'S
REPLACEMENT FROM THE AFTERSALES SERVICE.
REPLACEMENT DOES NOT FALL WITHINTHE PRODUCT WARRANTY AS
THE PART IS SUBJECT TO WEAR.
BURN POT PARTITION
FLAME GUARD
16

ENGLISH
IGNITION
Once the previously listed points have been checked, press key
OK
for three seconds to ignite the stove.
15 minutes are available for the ignition phase. After ignition and after reaching the control temperature, the
stove interrupts the ignition phase and switches to STARTUP.
STARTING
During the start-up phase, the stove stabilises combustion, increasing it progressively, to then start ventilation and switch to WORK.
WORK
During the work phase, the stove will function at the set power and work to reach the set room temperature. See next heading.
REGULATION OF SET THERMOSTAT
When the key
OK
is pressed, the set temperature is viewed; it can be changed using keys
OK
or
OK
from LOWTA-07 to 40°C - HOT.
The change must be confirmed by pressing the key
OK
.
LOWTA  HOT
If the temperature is set at "LOWTA" (set below the limit of 7°C), the stove will always run at minimum.
If the setting is on "HOT" (set above the limit of 40°C) the stove will not modulate, running only and always at the set power.
REGULATION OF SET POWER
The set power has 5 operating levels, When key
OK
is pressed, the set power is displayed; it can be changed using keys
OK
or
OK
.
Power 1 = minimum level - Power 5 = maximum level.
The change must be confirmed by pressing the key
OK
.
WORKING WITH ROOM PROBE STANDARD
The appliance monitors the room temperature using a probe incorporated into the handheld.
Once the set temperature has been reached, it will automatically switch to the minimum power level or turn o, activating the STANDBY
function, reducing pellet consumption to a minimum.
By factory default, the STBY function is always set to OFF.
For information on its activation and logic, follow the instructions on the next page, chapter: STANDBY.
BURN POT CLEANING
During the working phase, the stove has an internal timer, which after a pre-set period of time cleans the burn pot.
This phase is shown on the display, it lowers the stove power level and increases the ue gas exhaust motor for a programmed period of time.
When the cleaning phase is nished, the stove will re-start automatically and continue the working phase, returning to the selected power
level.
SWITCHOFF
Press the key
OK
for three seconds.
Once this operation has been performed, the appliance automatically enters the switch-o phase, blocking the supply of pellets.
The ue gas exhaust motor and the hot air ow motor will remain on until the stove temperature has dropped below the default
parameters.
REIGNITION
- The sTove can be re-igniTed only if The flue gas TemperaTure has lowered, and if The pre-seT Timer has been reseT.
OPERATION AND LOGIC
17

ENGLISH
USER MENU % PELLETS
V1 FAN
RESET
USER MENU
PELLETS
The following menu allows the regulation of the pellet feed percentage.
If the stove presents operational problems due to the quantity of pellets, pellet feeding can be regulated directly from the control board.
Problems linked to the quantity of fuel can be divided into 2 categories:
NO FUEL:
the stove can never develop a suitable ame, which tends to remain very LOW-TA even at high power levels.
at minimum power the stove tends to almost switch-o, triggering a“NO PELLETS”alarm.
if the stove displays the“NO PELLETS”alarm, there may be non-burned pellets inside the burn pot.
EXCESS FUEL:
the stove develops a very high ame even at LOW-TA power levels.
the viewing glass becomes very dirty, almost totally obscured.
the burn pot tends to become encrusted, blocking the air intake holes due to the excessive pellet feed, as these are only partially burned.
The percentage needs to be adjusted; the modication of this parameter will therefore lead to a proportional variation of all stove feeding
speeds. Feeding is from -30% to +20%.
V1  FAN
For specic models, from the menu it is possible to regulate the percentage ( +/- 10%) of the front fan speed.
USER MENU % PELLETS
V1 FAN
RESET
RESET
Allows the user to reset all modiable values to the default values.
USER MENU % PELLETS
V1 FAN
RESET
18

PRG1
START 00:00
STOP 00:00
321 4 5 6 7
25
C
°
CRONO
PRG1
PRG2
PRG3
PRG4
ENGLISH
J
WHEN THE WEEKLY PROGRAMMER IS ACTIVE, THE RELATIVE ICON WILL BE SHOWN ON THE HANDHELD
DISPLAY.
RECOMMENDATIONS EXAMPLE
The ignition and switch-o times must be within the space of one
day, from 0 to 24 and not over several days.
Before using the chrono function, set the current day and time.
Then check that the points listed in the “Set clock” sub-chapter
have been followed, to ensure the chrono function works. In
addition to being programmed, it must also be activated.
Ignition time 07:00 CORRECT
Switch-o time 18:00
Ignition time 22:00 INCORRECT
Switch-o time 05:00
SET CHRONO
ENABLE CHRONO
ENABLE CHRONO
Allows the chrono and the dierent stove time slots to be enabled/disabled.
Set temperature
Enabled days
Disabled days
1= Monday
7= Sunday
Programming 1
Ignition time
Switch-o time
Activated
Not activated
Programming 3
Programming 4
Programming 1
Programming 2
Chrono activation
This function allows the generator's ignition and switch-o to be automatically programmed. By factory
default, the SET CHRONO is disabled.
SET CHRONO ENABLE CHRONO
SET PRG1
SET PRG2
SET PRG3
SET PRG4
SET PRG 14
The chrono allows the programming of 4 time slots within a day, which can be used every day of the week. Ignition and switch-o times can
be set for each time slot, along with the specic days of application for the programmed time slot and the desired temperature. Current day
and time settings are essential for the correct operation of the Chrono.
19

ENGLISH
DUCTING
The menu allows the stove's ducting Z1 and Z2 to be controlled. For details on how ducting works, see chapter:" Ducting operation with
thermostat or probe (optional)"
DUCTING Z1 MODE ON/OFF/ECO Select Z1 DUCTING OPERATION MODE
SET ZONE Z1 OFF- 07 - 40°C Enable set Z1 ZONE TEMPERATURE
Z1 FAN % -20% a +20% Regulation of Z1 FAN FLOW SPEED
Z2 MODE ON/OFF/ECO Select Z2 DUCTING OPERATION MODE
SET ZONE Z2 OFF- 07 - 40°C Enable set Z2 ZONE TEMPERATURE
Z2 FAN % -20% a +20% Regulation of Z2 FAN FLOW SPEED
Z1 MODE
This setting makes it possible to select the Z1 ducting motor working mode.
OFF: The ducting is always disabled.
ON: The ducting is active and when the temperature is reached the ducting motor will switch to the 1st speed.
ECO: The ducting is active and when the temperature is reached the ducting motor will turn o.
SET ZONE Z1
This setting allows configuration for the use of a room thermostat or room probe (NTC 10K) to control the temperature of room Z1.
OFF: congured for use with room thermostat.
07-40°C: congured for use with a room probe, with the possibility to adjust the desired temperature.
Z1 FAN %
Allows the regulation of the Z1 air ow speed - in %.
same seTTings for Z2 ducTing
SETTINGS
SETTINGS SET CLOCK xx:xx - dd/mm/yy Date and time setting
LANGUAGE ita-ing-fra-ted-spa Language setting
DISPLAY Display regulation
STANDBY On/o Enables or disables the STANDBY FUNCTION
DELTA T OFF - 0.5 - 5.5°C DELTA T regulation
The set settings allow:
Regulation of daTe and Time
Preferred language setting (Italian, English, French, German, Spanish)
Regulation of display
Enable/disable sTand-by
Set the delTa T settings
SET CLOCK
see chapter: commissioning settings.
LANGUAGE
see chapter: commissioning settings.
20