Extron electronics Cable Cubby 1200 User manual

1
IMPORTANT:
Go to www.extron.com for the
complete user guide, installation
instructions, and specifications.
Cable Cubby 1200 and 1400 • Installation Guide
This guide provides instructions for an experienced installer to install and connect the Extron
Cable Cubby 1200 and 1400.
The Cable Cubby units are furniture-mounted enclosures for cable access, connections,
and AC power. Cables that are not in use can be stored out of the way while
remaining connected to the presentation system.
Cable Cubby 1200 Cable Cubby 1400
Hole Plugs
Connectivity Bracket Cable Grommet Plate
AAP Frame Plate
Cable Cubby 1200 Cable Cubby 1400
Zip Ties
Tweeker AC Power Module
125V~12A MAX TOTAL
Retractor Bracket Retractor Pin & Clip
#6 Mounting Screws
and Star Washers
#4-40 Module Screws
1 2
4 8
Hole Plugs
Connectivity Bracket Cable Grommet Plate
AAP Frame Plate
Cable Cubby 1200 Cable Cubby 1400
Zip Ties
Tweeker AC Power Module
125V~12A MAX TOTAL
Retractor Bracket Retractor Pin & Clip
#6 Mounting Screws
and Star Washers
#4-40 Module Screws
1 2
Hole Plugs
Connectivity Bracket Cable Grommet Plate
AAP Frame Plate
Cable Cubby 1200 Cable Cubby 1400
Zip Ties
Tweeker AC Power Module
125V~12A MAX TOTAL
Retractor Bracket Retractor Pin & Clip
#6 Mounting Screws
and Star Washers
#4-40 Module Screws
1 2
Hole Plugs
Connectivity Bracket Cable Grommet Plate
AAP Frame Plate
Cable Cubby 1200 Cable Cubby 1400
Zip Ties
Tweeker AC Power Module
125V~12A MAX TOTAL
Retractor Bracket Retractor Pin & Clip
#6 Mounting Screws
and Star Washers
#4-40 Module Screws
6 (3/8"), 2 (1/4") 12 (3/8"), 4 (1/4")
Hole Plugs
Connectivity Bracket Cable Grommet Plate
AAP Frame Plate
Cable Cubby 1200 Cable Cubby 1400
Zip Ties
Tweeker AC Power Module
125V~12A MAX TOTAL
Retractor Bracket Retractor Pin & Clip
#6 Mounting Screws
and Star Washers
#4-40 Module Screws
1 2
Hole Plugs
Connectivity Bracket Cable Grommet Plate
AAP Frame Plate
Cable Cubby 1200 Cable Cubby 1400
Zip Ties
Tweeker AC Power Module
125V~12A MAX TOTAL
Retractor Bracket Retractor Pin & Clip
#6 Mounting Screws
and Star Washers
#4-40 Module Screws
1 2
8 16
Hole Plugs
Connectivity Bracket Cable Grommet Plate
AAP Frame Plate
Cable Cubby 1200 Cable Cubby 1400
Zip Ties
Tweeker AC Power Module
125V~12A MAX TOTAL
Retractor Bracket Retractor Pin & Clip
#6 Mounting Screws
and Star Washers
#4-40 Module Screws
1 1
Hole Plugs
Connectivity Bracket Cable Grommet Plate
AAP Frame Plate
Cable Cubby 1200 Cable Cubby 1400
Zip Ties
Tweeker AC Power Module
125V~12A MAX TOTAL
Retractor Bracket Retractor Pin & Clip
#6 Mounting Screws
and Star Washers
#4-40 Module Screws
Planning
Check with local and state regulations before starting the
installation:
Ensure that the planned installation complies with building and electrical codes.
Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility requirements.
Check all parts and equipment before installation:
Ensure that all parts are present in each kit.
Ensure that necessary tools and equipment are available for the installation.
Kit Contents
Hole Plugs
Connectivity Bracket Cable Grommet Plate
AAP Frame Plate
Cable Cubby 1200 Cable Cubby 1400
Zip Ties
Tweeker AC Power Module
125V~12A MAX TOTAL
Retractor Bracket Retractor Pin & Clip
#6 Mounting Screws
and Star Washers
#4-40 Module Screws
Hole Plugs
Connectivity Bracket Cable Grommet Plate
AAP Frame Plate
Cable Cubby 1200 Cable Cubby 1400
Zip Ties
Tweeker AC Power Module
125V~12A MAX TOTAL
Retractor Bracket Retractor Pin & Clip
#6 Mounting Screws
and Star Washers
#4-40 Module Screws
Hole Plugs
Connectivity Bracket Cable Grommet Plate
AAP Frame Plate
Cable Cubby 1200 Cable Cubby 1400
Zip Ties
Tweeker AC Power Module
125V~12A MAX TOTAL
Retractor Bracket Retractor Pin & Clip
#6 Mounting Screws
and Star Washers
#4-40 Module Screws

Cable Cubby 1200 and 1400 • Installation Guide (Continued)
2
Preparing the Table
Cut a hole in the surface where the enclosure will be installed. Read the following information before making a cut.
Determine the best location for the enclosure
Ensure that the location where the Cable Cubby is to be installed is convenient for as many users as possible.
Ensure that the edge on which the lid opens is oriented correctly.
Ensure that there is ample space under the table for cables.
When installing retractors in the Cable Cubby, ensure that there is enough space for the retractor assembly under the table
or furniture. See dimensions for the retractors below.
Choose a method for cutting the hole in the table
The opening in the table for the Cable Cubby should be cut only by licensed and bonded craftspeople.
CAUTION:
• Wear safety glasses when cutting the hole in the table. Failure to comply may result in eye injury.
• The Cable Cubby edges are sharp. Exercise care to prevent scarring or damaging the skin and furniture.
Choose one of the following methods for cutting the hole:
Hand Router and Routing Template Jigsaw and Paper Cut-Out Template CNC Wood Router
If using a CNC wood router or other
precise machinery, use the exact
cut-out dimensions for your model
(see the table below).
Visit www.extron.com for Cable Cubby routing
template part numbers and instructions.
Dimensions and print-out templates are
available online at www.extron.com.
Product
Cut-out Dimensions
User Access
Width
Side
Dimension
CC 1200 10.00"
(254.0 mm)
4.00"
(101.6 mm)
CC 1400 10.00"
(254.0 mm)
6.75"
(171.5 mm)
23.5"
(59.7 cm)
29.4"
(74.7 cm)
26.7"
(67.8 cm)
10.6"
(26.9 cm)
30
Table Top
17.8"
(45.2 cm)
23.7"
(60.2 cm)
XL Models
9.2"
(23.4 cm)
14.9"
(37.8 cm)
20.8"
(52.8 cm)
XL Models
Cut-Out Template for the Extron
Cable Cubby 1200
Outer Edge of Front Bezel
(Do not cut this line.)
1. Confirm the product to be installed.
2. Remove the surface cut-out area
(gray) from the template.
3. Measure the cutout and template.
4. Mark the position on the
furniture where the Cable Cubby 1200
will be installed.
5. Double check the dimensions and position,
then cut the opening.
Trim Ring
Lip
Cut-OutRadius:
0.25" (0.6 cm)
User Access
P/N 68-2472-01 Rev.A
Page Size: 11" x 17"
Print Scale 1:1
Do not Shrink

3
Preparing the Cable Cubby
Step 1 — Assemble Connectivity Modules.
Connectivity modules allow you to populate the Cable Cubby enclosure with a combination of AAPs, cable pass-through, or
retractors. Follow the steps below to assemble the connectivity modules of your choice.
Option 1: AAP Module
Option 2: Cable Pass-Through Module
Option 3: Retractor Bracket
NOTE: After assembling the module, proceed to Step 2 — Install the Modules on the next page.
NOTE: After assembling the module, proceed to Step 2 — Install the Modules on the next page.
NOTE:
• After installing the bracket, proceed to
Step 2 — Install the Modules on the
next page to install the power module.
• Retractors are installed after the Cable
Cubby is mounted on the table (see
Mounting Retractors Under the Table
on page 5).
Secure up to three single-space
AAPs in the AAP plate.
Secure the AAP plate on the connectivity brackets,
using four of the provided module screws.
#4-40 Nut
w/ Captive Washer
Insert cables through the bottom of the connectivity bracket.
Connect cables to the AAPs.
Insert cables through the bottom of the connectivity bracket
and into the holes of the grommet plate.
Secure the grommet plate on the
connectivity bracket, using four
of the provided module screws.
Snap the included hole plugs into
any unused holes.
1
2
3
1
2
3
Secure up to three single-space
AAPs in the AAP plate.
Secure the AAP plate on the connectivity brackets,
using four of the provided module screws.
#4-40 Nut
w/ Captive Washer
Insert cables through the bottom of the connectivity bracket.
Connect cables to the AAPs.
Insert cables through the bottom of the connectivity bracket
and into the holes of the grommet plate.
Secure the grommet plate on the
connectivity bracket, using four
of the provided module screws.
Snap the included hole plugs into
any unused holes.
1
2
3
1
2
3
Secure the bracket using four of the
provided mounting screws with star washers.
Insert the bracket
into the Cable Cubby.
S
p
The bracket may be installed
on the left or right side of the
enclosure and at the lowest height.
1
2

4
Mounting the Cable Cubby in the Table
Mount the Cable Cubby flush with the table.
CAUTION: The Cable Cubby edges are sharp. Exercise care to prevent scarring or damaging the skin and furniture.
Step 2 — Install the Modules.
Determine where the connectivity modules and power module will be installed in the Cable Cubby. The modules may be installed
on the left or right side of the enclosure and at various heights.
NOTE: Ensure that there is enough room above the modules for the Cable Cubby lid to close completely.
WARNING: Electric shock hazard. To ensure proper electrical grounding,
use the provided #6-32 mounting screws with the star washers.
Remove the plastic strips and
lm on the surface of the
Cable Cubby.
Ensure that the
side clamps are
seated against the
enclosure.
Lower the Cable Cubby into the hole to test the t.
If necessary, carefully enlarge the opening.
Secure the modules using four of the provided mounting screws and star washers.
Insert the modules
into the Cable Cubby.
1
2
1
23
Remove the plastic strips and
lm on the surface of the
Cable Cubby.
Ensure that the
side clamps are
seated against the
enclosure.
Lower the Cable Cubby into the hole to test the t.
If necessary, carefully enlarge the opening.
Secure the modules using four of the provided mounting screws and star washers.
Insert the modules
into the Cable Cubby.
1
2
1
23

5
Cable Cubby 1200 and 1400 • Installation Guide (Continued)
Under the table, adjust the side clamps on the enclosure.
Mounting Retractors Under the Table
Horizontal or Angular Mounting
For installation details, see the Cable Retractor
Setup Guide available online at www.extron.com.
Insert the pin through the
retractor mounting hole on
the side of the Cable Cubby
and retractor assembly.
Secure the clip on the pin.
Insert retractors into
the retractor bracket.
Secure the locking screw on each
retractor. Do not overtighten.
For horizontal or angular mounting, r
emove
these orientation screws (front and back),
then follow the steps shown at left.
Rotate the side clamp
outward and ensure that
the lever is down.
Slide the clamp all the
way up against the bottom
of the table.
Ensure the Cable Cubby
is rmly seated in the table.
Raise the lever to secure
the Cable Cubby.
Lever
1
2
3
4
12 3
NOTE: To lower the side
clamp, turn the lever
down, then press and
hold the locking plate
while sliding down the
clamp.
Locking
plate
Insert the pin through the
retractor mounting hole on
the side of the Cable Cubby
and retractor assembly.
Secure the clip on the pin.
Insert retractors into
the retractor bracket.
Secure the locking screw on each
retractor. Do not overtighten.
For horizontal or angular mounting, remove
these orientation screws (front and back),
then follow the steps shown at left.
Rotate the side clamp
outward and ensure that
the lever is down.
Slide the clamp all the
way up against the bottom
of the table.
Ensure the Cable Cubby
is rmly seated in the table.
Raise the lever to secure
the Cable Cubby.
Lever
1
2
3
4
12 3
Insert the pin through the
retractor mounting hole on
the side of the Cable Cubby
and retractor assembly.
Secure the clip on the pin.
Insert retractors into
the retractor bracket.
Secure the locking screw on each
retractor. Do not overtighten.
For horizontal or angular mounting, remove
these orientation screws (front and back),
then follow the steps shown at left.
Rotate the side clamp
outward and ensure that
the lever is down.
Slide the clamp all the
way up against the bottom
of the table.
Ensure the Cable Cubby
is rmly seated in the table.
Raise the lever to secure
the Cable Cubby.
Lever
1
2
3
4
12 3

68-2451-50
Rev. B
11 13
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX [phone] FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2013 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Installation Checklist
Planning (page 1)
Check with local and state regulations before starting the installation.
Check all parts and equipment before installation.
Preparing the Table (page 2)
Determine the best location for the enclosure.
Choose a method for cutting the hole in the table.
Preparing the Cable Cubby (page 3)
Choose between AAPs, cable-pass through, and retractor connectivity to populate the Cable Cubby.
Secure the brackets and power module in the Cable Cubby.
Mounting the Cable Cubby in the Table (page 4)
Mount the Cable Cubby ush with the table.
Mounting Retractors Under the Table (page 5)
Routing and Connecting Cables (page 6)
Routing and Connecting Cables
For cable pass-through applications,
allow at least 36 inches (0.9 m) of cable
loop for each cable.
Connect cables to the AV system
and connect the AC power cord.
Using zip ties, secure cables to the holes
on the bottom of the Cable Cubby.
1
2
3