FAAC Genuine XKP W User manual

ABN 27 106 103 315
www.aggdoors.com.au
[e-mail]
[phone]
Genuine XKP W Wireless Keypad
Programming
The programming function is PWD protected. In order to restrict access, set a new
PWD when the system is programmed for the first time. Do not give the PWD to
other people.
Factory-set PWD: 1 2 3 4
When the XKP W is waiting for an operation, enter: # PWD # then choose the
option 1-12 from the menu and carry out the procedure following the instructions.
E.g: for a new user code, enter: 1 # (look for the instructions 1)
Menu
1Store a user code
2Delete a user code
3Delete all user codes
4Change the PWD
5Restore factory settings
6Direct radio channel button E
7not used
8Teach the radio code
9Learn the radio code
10 Set the XKP W SLAVE
11 Randomize the radio code
12 Easy or Advanced Operation

If the XKP W indicates an ERROR (beeping 5x with red LED fast flashing), it should
be reprogrammed correctly. After the OK (beeping once with green LED on for 0.5
s) message appears, the XKP W waits for an operation for 60 s.
When the XKP W is waiting for an operation, it is possible to carry out another
operation from the menu. Press Eto end the programming (it will also end when
no key being pressed after time out).
1. STORE A USER CODE
This stores the user codes that must be entered to activate the radio channels. You
can choose Easy or Advanced mode of operation. Only number codes can be
entered. If you attempt to store a code that is already in memory, the XKP W
signals an error.
➢Easy operation
User codes consisting of 4 numbers, in various combinations. Each code can be
enabled for only 1 radio channel, to be specified when it is being stored.
When the XKP W is waiting for an operation, enter:
1 # code # code E Ch #
➢Advanced operation
User codes of variable length from 2 to 6 digits, in various combinations. Each
code can be enabled for 1, several or all of the radio channels available.
When the XKP W is waiting for an operation, enter:
1 # code # code # (enables all channels)
Or
1 # code # code E Ch # (enables only 1 channel)
Or
1 # code # code E Ch Ch … # (enables several channels)
2. DELETE A USER CODE
When the XKP W is waiting for an operation, enter:
2 # code # code #
3. DELETE ALL USER CODE
When the XKP W is waiting for an operation, enter:
3 # 3 #

4. CHANGE THE PWD
Enter the PWD (maximum of 6 digits). Only numeric codes can be entered.
When the XKP W is waiting for an operation, enter:
4 # new PWD # new PWD #
5. RESTORE FACTORY SETTINGS
This restores the XKP W to its factory settings: user code memory empty, direct
radio channel (button E) disabled, Easy Operation, PWD: 1 2 3 4, randomized radio
codes. When finished, the XKP W exits from programming mode and goes into
standby.
When the XKP W is waiting for an operation, enter:
5 # 5 #
6. DIRECT RADIO CHANNEL BUTTON E
Button E can be used to activate a radio channel without having to enter a user
code (direct radio channel).
By default, the direct radio channel button E is disabled. To enable it, specify the
radio channel (Ch. no. from 1 to 4) to be activated. To disable it, press 0 instead of
the number of the radio channel.
When the XKP W is waiting for an operation, enter:
6 # Ch # (enabled on the radio channel entered)
Or
6 # 0 # (disabled)
7. **NOT USED
8. TEACH THE RADIO CODE
This allows a master XKP W to ‘teach’ the radio code of a channel to a target
device. This procedure must be carried our for each radio channel that you wish to
use. Only the master XKP W devices can teach the codes.
•If the XKP W is installed on a new radio system, it must teach it to a Radio
Receiver.
•If the XKP W is already being used on the radio receiver and you wish to
add a radio transmitter, the target device can be a radio control or an
additional Master or Slave XKP W.
Follow the procedures indicated below according to the target device.

TEACH A RADIO RECEIVER
When the XKP W is waiting for an operation, enter:
8 # Ch
Place the receiver in learning mode on the required radio channel within 25 s
(follow the receiver’s instruction and maintain the recommended distance between
the devices), then press:
#(keep it pressed until confirmation is given that the code has been learnt, then release it)
The code of the radio channel entered is transmitted (Green LED on). Make sure
that the receiver confirms that the code has been learnt (receiver’s instructions).
Repeat the procedure for each radio channel required. When using the XKP W for
the first time, each radio channel has to be activated twice in succession:
Easy Operation enter:
User code E wait until the Green LED turns off, then press E
Advanced Operation enter:
# user code E Ch. wait until the green LED turns off, then repeat Ch.
TEACH ANOTHER XKP W
When the XKP W is waiting for an operation, enter:
8 # Ch
Place the target XKP W into learning mode on the
required radio channel within 25 S and bring the two
devices into contact with one another as shown in the
figures. Then press:
#(keep it pressed until confirmation is given that the code
has been learnt, then release it)
The code of the radio channel entered is transmitted
(Green LED on). Make sure that the target XKP W
confirms that it has been learnt: Green LED on for 0.5
and 1 beep.
Repeat the procedure for each radio channel required. When using the new XKP W
for the first time, each radio channel has to be activated twice in succession.
Easy Operation enter:
User code Ewait until the Green LED turns off, then press E
Advanced Operation enter:
#user code E Ch. wait until the green LED turns off, then repeat Ch.

TEACH A RADIO CONTROL
When the XKP W is waiting for an operation, enter:
8 # Ch
Bring the two devices into contact with one another
within 25 s, as shown in the figure, then press:
#(keep it pressed until confirmation is given that the code
has been learnt, then release it)
The code of the radio channel entered is transmitted
(Green LED on). At the same time, press the button of
the radio control and make sure that the confirmation is
given (the LED if the radio control will flash twice and
then switch off).
Repeat the procedure for each radio channel required. When using the radio
control for the first time, each radio channel has to be activated twice in quick
succession.
9. LEARN THE RADIO CODE
This procedure allows the radio code of a channel to be ‘learnt’ from a SLH master
radio transmitter. This procedure must be carried out for each radio channel that
you wish to use.
Both Master XKP W and Slave XKP W units can learn the code. The teaching device
must be a SLH master radio transmitter.
When the XKP W is waiting for an operation, enter:
9 # Ch #
Bring the two devices into contact with one another within 25 s and transmit the
radio code from the radio control or from the teaching XKP W:
•On the radio control press buttons P1 and P2 simultaneously, then release
them and press the channel number.
•On the teaching XKP W follow the entire procedure indicated in 8
The XKP W learns the radio code on the channel entered, signals OK and waits for
an operation.
Repeat the procedure for each radio channel required. When using the XKP W for
the first time, each radio channel has to be activated twice in succession:
Easy Operation enter:
User code Ewait until the Green LED turns off, then press E
Advanced Operation enter:
#user code E Ch. wait until the green LED turns off, then repeat Ch

10. SET THE XKP W SLAVE
This operation is irreversible and converts the XKP W, which is factory set to
Master, into a Slave device. A Slave XKP W can learn, but cannot teach a radio
code.
When the XKP W is waiting for an operation, enter:
10 # 105 #
11. RANDOMISE THE RADIO CODES
This reassigns new radio code to the XKP W for all radio channels. Once this has
been done, the XKP W keeps the settings and any user codes that were created,
but in order for it to function, the XKP W has to be stored again on all the radio
receivers on which it has to be operate.
When the XKP W is waiting for an operation, enter:
11 # 114 #
12. EASY OR ADVANCED OPERATION
It is only possible to carry out this operation if the user code memory is empty.
When the XKP W is waiting for an operation, enter:
12 # 0 # (enables East Operation)
Or
12 # 1 # (enables Advanced Operation)
Signal on XKP W
OK ✓1 beep for 0.5 s (Green LED on)
ERROR  5 beeps (Red LED fast flashing)
TIMEOUT󰬉󰬊󰬋󰬌󰬍󰬎󰬏60 s (Red LED flashing)
Waiting for operation
STANDBY LED on (Green and Red)