Fagor CNC 8070 Quick guide

CNC 8070
(REF: 1007)
HARDWARE CONFIGURATION
(Ref: 1007)

MACHINE SAFETY
It is up to the machine manufacturer to make sure that the safety of the machine
is enabled in order to prevent personal injury and damage to the CNC or to the
products connected to it. On start-up and while validating CNC parameters, it
checks the status of the following safety elements:
• Feedback alarm for analog axes.
• Software limits for analog and sercos linear axes.
• Following error monitoring for analog and sercos axes (except the spindle)
both at the CNC and at the drives.
• Tendency test on analog axes.
If any of them is disabled, the CNC shows a warning message and it must be
enabled to guarantee a safe working environment.
FAGOR AUTOMATION shall not be held responsible for any personal injuries or
physical damage caused or suffered by the CNC resulting from any of the safety
elements being disabled.
HARDWARE EXPANSIONS
FAGOR AUTOMATION shall not be held responsible for any personal injuries or
physical damage caused or suffered by the CNC resulting from any hardware
manipulation by personnel unauthorized by Fagor Automation.
If the CNC hardware is modified by personnel unauthorized by Fagor Automation,
it will no longer be under warranty.
COMPUTER VIRUSES
FAGOR AUTOMATION guarantees that the software installed contains no
computer viruses. It is up to the user to keep the unit virus free in order to
guarantee its proper operation.
Computer viruses at the CNC may cause it to malfunction. An antivirus software
is highly recommended if the CNC is connected directly to another PC, it is part
of a computer network or floppy disks or other computer media is used to transmit
data.
FAGOR AUTOMATION shall not be held responsible for any personal injuries or
physical damage caused or suffered by the CNC due a computer virus in the
system.
If a computer virus is found in the system, the unit will no longer be under warranty.
All rights reserved. No part of this documentation may be transmitted,
transcribed, stored in a backup device or translated into another language
without Fagor Automation’s consent. Unauthorized copying or distributing of this
software is prohibited.
The information described in this manual may be changed due to technical
modifications. Fagor Automation reserves the right to make any changes to the
contents of this manual without prior notice.
All the trade marks appearing in the manual belong to the correspondingowners.
The use of these marks by third parties for their own purpose could violate the
rights of the owners.
It is possible that CNC can execute more functions than those described in its
associated documentation; however, Fagor Automation does not guarantee the
validity of those applications. Therefore, except under the express permission
from Fagor Automation, any CNC application that is not described in the
documentation must be considered as "impossible". In any case, Fagor
Automation shall not be held responsible for any personal injuries or physical
damage caused or suffered by the CNC if it is used in any way other than as
explained in the related documentation.
The content of this manual and its validity for the product described here has been
verified. Even so, involuntary errors are possible, thus no absolute match is
guaranteed. Anyway, the contents of the manual is periodically checked making
and including the necessary corrections in a future edition. We appreciate your
suggestions for improvement.
The examples described in this manual are for learning purposes. Before using
them in industrial applications, they must be properly adapted making sure that
the safety regulations are fully met.

Hardware configuration
CNC 8070
(REF: 1007)
·3·
INDEX
About the product ....................................................................................................................... 7
Declaration of conformity ............................................................................................................ 9
Version history .......................................................................................................................... 11
Safety conditions ...................................................................................................................... 13
Warranty terms ......................................................................................................................... 17
Material returning terms ............................................................................................................ 19
CNC maintenance .................................................................................................................... 21
Related documentation ............................................................................................................. 23
CHAPTER 1 PREVIOUS INFORMATION.
CHAPTER 2 HARDWARE STRUCTURE.
2.1 Possible configurations. ............................................................................................... 29
CHAPTER 3 HEAT DISSIPATION. CENTRAL UNIT (CPU) ENCLOSURE.
3.1 Heat dissipation models. .............................................................................................. 35
CHAPTER 4 CENTRAL UNITS ICU - MCU.
4.1 Technical characteristics. ............................................................................................. 39
4.2 MCU central unit dimensions. ...................................................................................... 41
4.3 MCU-PCI central unit dimensions. ............................................................................... 42
4.4 ICU central unit dimensions. ........................................................................................ 43
4.4.1 Dimensions of the central unit without monitor. ....................................................... 43
4.4.2 Dimensions of the central unit with LCD-10 monitor. ............................................... 44
4.4.3 Dimensions of the central unit with LCD-10K monitor. ............................................. 45
4.4.4 Dimensions of the central unit with LCD-15 monitor. ............................................... 46
4.5 Dimensions and characteristics of the enclosure. ........................................................ 47
4.6 Elements (connectors). ................................................................................................ 50
4.6.1 Peripheral board. ...................................................................................................... 50
4.6.2 Expansion board. ..................................................................................................... 53
4.6.3 CPU board. .............................................................................................................. 56
4.6.4 PCI expansion board (only for the MCU model). ..................................................... 58
4.6.5 Operator panel (only LCD-10K) ............................................................................... 60
4.6.6 Digital inputs and outputs. Electrical characteristics. ............................................... 61
4.6.7 Feedback inputs. Technical characteristics and connection. ................................... 62
4.7 Power connection. ....................................................................................................... 64
4.8 housing for the compact flash and battery-powered RAM memory. ............................ 65
4.9 Insert the board into the PCI expansion (only in MCU models). .................................. 66
4.10 RS232 serial line connection. ...................................................................................... 68
4.11 RS422 serial line connection. ...................................................................................... 70
4.12 RS485 serial line connection. ...................................................................................... 72
4.13 Probe connection. ........................................................................................................ 74
4.14 Connection to an Ethernet network. ............................................................................. 76
CHAPTER 5 LCD-15SVGA. PASSIVE MONITOR " LCD15-SVGA".
5.1 Possible configurations. ............................................................................................... 78
5.2 Technical characteristics. ............................................................................................. 79
5.3 Hardware dimensions. ................................................................................................. 80
5.4 Dimensions and characteristics of the enclosure. ........................................................ 81
5.5 Elements (connectors). ................................................................................................ 82
5.6 Overall connection. ...................................................................................................... 83
CHAPTER 6 OP-PANEL-H/E MODULE. KEYBOARD AND OPERATOR PANEL.
6.1 Hardware dimensions. ................................................................................................ 85
6.2 Dimensions and characteristics of the enclosure. ........................................................ 86
6.3 Elements (connectors). ................................................................................................ 87

·4·
Hardware configuration
CNC 8070
(REF: 1007)
CHAPTER 7 KB-PANEL-H MODULE. INDEPENDENT KEYBOARD.
7.1 Hardware dimensions. ................................................................................................ 91
7.2 Dimensions and characteristics of the enclosure. ....................................................... 92
7.3 Elements (connectors). ................................................................................................ 93
CHAPTER 8 JOG-PANEL MODULE. INDEPENDENT OPERATOR PANEL.
8.1 Hardware dimensions. ................................................................................................ 95
8.2 Dimensions and characteristics of the enclosure. ....................................................... 96
8.3 Elements (connectors). ................................................................................................ 97
CHAPTER 9 MOUSE MODULE.
9.1 Hardware dimensions. .............................................................................................. 101
CHAPTER 10 RIO70 REMOTE MODULES. (CANFAGOR PROTOCOL).
10.1 Dimensions and mounting of the modules. ................................................................ 104
10.2 Consumption of the remote modules. ........................................................................ 106
10.3 Power Supply. ............................................................................................................ 107
10.3.1 Elements (connectors). .......................................................................................... 108
10.4 Digital inputs and outputs. ......................................................................................... 110
10.4.1 Elements (connectors). .......................................................................................... 111
10.5 Analog inputs and outputs. ........................................................................................ 112
10.5.1 Elements (connectors). .......................................................................................... 113
10.6 Feedback inputs (counter). ........................................................................................ 114
10.6.1 Elements (connectors). .......................................................................................... 115
10.7 Electrical characteristics of the inputs and outputs. ................................................... 116
10.8 Feedback inputs. Technical characteristics and connection. ..................................... 117
10.9 Numbering of the digital inputs and outputs. ............................................................. 119
10.10 Numbering of the analog inputs and outputs and of the feedback inputs. ................. 121
10.11 Probe connection. ...................................................................................................... 122
CHAPTER 11 RIO5 REMOTE MODULES. (CANOPEN PROTOCOL).
11.1 Dimensions and mounting of the modules. ................................................................ 126
11.2 Power supply. ............................................................................................................ 127
11.2.1 Elements (connectors). .......................................................................................... 129
11.3 Digital inputs and digital outputs (single module). ..................................................... 133
11.3.1 Elements (connectors). .......................................................................................... 134
11.4 Digital inputs and digital outputs (double module). .................................................... 135
11.4.1 Elements (connectors). .......................................................................................... 136
11.5 Electrical characteristics of the inputs and outputs. ................................................... 137
11.6 Numbering of the digital inputs and outputs. ............................................................. 139
11.7 Numbering of the analog inputs and outputs and of the temperature sensor inputs. 141
CHAPTER 12 RIOW REMOTE MODULES. (CANOPEN PROTOCOL).
12.1 Dimensions of the modules. ...................................................................................... 143
12.2 Technical and electrical characteristics. .................................................................... 144
12.2.1 Technical characteristics. ....................................................................................... 144
12.2.2 Electrical characteristics of the inputs and outputs. ............................................... 146
12.3 Sizing of the remote groups. ...................................................................................... 148
12.4 Installation of the modules. ....................................................................................... 150
12.5 RIOW-CANOPEN-ECO module. Leading (first) module. ........................................... 153
12.5.1 Elements (connectors). .......................................................................................... 154
12.5.2 Node configuration. ................................................................................................ 155
12.5.3 Meaning of the LED's. ............................................................................................ 157
12.6 RIOW-CANOPEN-STAND module. Leading (first) module. ...................................... 160
12.6.1 Elements (connectors). .......................................................................................... 161
12.6.2 Voltage supply for the module. .............................................................................. 163
12.6.3 Node configuration. ................................................................................................ 164
12.6.4 Meaning of the LED's. ............................................................................................ 166
12.7 RIOW-PS24 module. ................................................................................................. 170
12.7.1 Elements (connectors). .......................................................................................... 171
12.8 RIOW-8DI module. Module of 8 digital inputs. ........................................................... 172
12.8.1 Elements (connectors). .......................................................................................... 173
12.9 RIOW-8DO module. Module of 8 digital outputs. ....................................................... 174
12.9.1 Elements (connectors). .......................................................................................... 175
12.10 RIOW-4AI module. Module of 4 analog inputs. ......................................................... 176
12.10.1 Elements (connectors). .......................................................................................... 177
12.11 RIOW-4AO module. Module of 4 analog outputs. ..................................................... 178
12.11.1 Elements (connectors). .......................................................................................... 179

Hardware configuration
CNC 8070
(REF: 1007)
·5·
12.12 RIOW-2AI-PT100 module. Module of 2 inputs for PT100 temperature sensors. ....... 180
12.12.1 Elements (connectors). .......................................................................................... 181
12.13 RIOW-END module. Last module of the group. ......................................................... 182
12.14 Numbering of the digital inputs and outputs. .............................................................. 183
12.15 Numbering of the analog inputs and outputs and of the temperature sensor inputs. 185
CHAPTER 13 EMERGENCY BATTERY.
13.1 Battery dimensions. .................................................................................................. 187
13.2 Connectors and connection. ...................................................................................... 188
13.3 Operation of the emergency battery. ......................................................................... 189
CHAPTER 14 BUS CAN (CANFAGOR/CANOPEN PROTOCOLS).
14.1 Identification of the modules at the bus. .................................................................... 192
14.2 Type of CAN bus and baudrate. ................................................................................ 194
14.3 Selecting the baudrate for the CANopen bus. ........................................................... 195
14.4 Selecting the speed for the CANfagor bus. ................................................................ 197
CHAPTER 15 SERCOS BUS.
15.1 Module identification and connection ......................................................................... 200
15.2 Data exchange via Sercos. ........................................................................................ 201
CHAPTER 16 MECHATROLINK BUS.
CHAPTER 17 INSTALLING AND CONFIGURING A THIN CLIENT (EPATEC MODEL).
17.1 Install and configure the communication software at the CNC. ................................. 206
17.2 Configuring the Thin Client. ....................................................................................... 208
17.2.1 Configure the network protocol (for network or point-to point connection). ............ 208
17.2.2 Configure the communication between the CNC and the Thin Client. ................... 209
17.2.3 Configuring the startup of the Thin Client. .............................................................. 210
17.2.4 Disable the mouse at the Thin Client. .................................................................... 211

Hardware configuration
CNC 8070
(REF: 1007)
·7·
ABOUT THE PRODUCT
BASIC CHARACTERISTICS.
Basic characteristics. ·BL· ·OL· ·M· / ·T·
PC-based system. Closed system Open system
Operating system. Windows XP
Number of axes. 3 to 7 3 to 28
Number of spindles. 1 1 to 4
Number of tool magazines. 1 1 to 4
Number of execution channels. 1 1 to 4
Number of handwheels. 1 to 12
Type of servo system. Analog / Digital Sercos / Digital Mechatrolink
Communications. RS485 / RS422 / RS232
Ethernet
PCI expansion. No Option No
Integrated PLC.
PLC execution time.
Digital inputs / Digital outputs.
Marks / Registers.
Timers / Counters.
Symbols.
< 1ms/K
1024 / 1024
8192 / 1024
512 / 256
Unlimited
Block processing time. < 1 ms
Remote modules. RIOW RIO5 RIO70
Communication with the remote modules. CANopen CANopen CANfagor
Digital inputs per module. 8 16 or 32 16
Digital outputs per module. 8 24 or 48 16
Analog inputs per module. 4 4 8
Analog outputs per module. 4 4 4
Inputs for PT100 temperature sensors. 2 2 - - -
Feedback inputs. - - - - - - 4
Differential TTL
Sinusoidal 1 Vpp
Customizing.
PC-based open system, fully customizable.
INI configuration files.
FGUIM visual configuration tool.
Visual Basic®, Visual C++®, etc.
Internal databases in Microsoft® Access.
OPC compatible interface

·8·
Hardware configuration
CNC 8070
(REF: 1007)
SOFTWARE OPTIONS.
Bear in mind that some of the features described in this manual depend on the software options that are
installed. The information of the following table is informative only; when purchasing the software options,
only the information provided in the ordering handbook is valid.
-BL- model -OL- model -M- model -T- model
Open system.
Access to the administrator mode.
- - - Option Option Option
Editing and simulation environment. - - - Option Option Option
Number of execution channels 1 1 to 4 1 to 4 1 to 4
Number of axes 3 to 7 3 to 28 3 to 28 3 to 28
Number of spindles 1 1 to 4 1 to 4 1 to 4
Number of tool magazines 1 1 to 4 1 to 4 1 to 4
Number of interpolated axes 2 to 4 2 to 28 2 to 28 2 to 28
COCOM version Standard Option Option Option
Dual-purpose machines (M-T) - - - Option Option Option
Non-Fagor digital drive Option Option Option Option
Tool radius compensation Option Option Standard Standard
"C" axis Option Option Standard Option
RTCP transformation Option - - - Option Option
High speed machining (HSC). Option Option Option Option
Probing canned cycles - - - - - - Option Option
Drilling ISO cycles for the OL model.
(G80, G81, G82, G83).
- - - Option - - - - - -
Tandem axes - - - Option Option Option
Synchronism and cams Option Option Option Option
Tangential control Option Option Option Option

Hardware configuration
CNC 8070
(REF: 1007)
·9·
DECLARATION OF CONFORMITY
The manufacturer:
Fagor Automation, S. Coop.
Barrio de San Andrés Nº 19, C.P. 20500, Mondragón -Guipúzcoa- (SPAIN).
Declares:
The manufacturer declares under their exclusive responsibility the conformity of the product:
8070 CNC
Consisting of the following modules and accessories:
8070-M-ICU, 8070-T-ICU, 8070-OL-ICU, 8070-BL-ICU
8070-M-MCU, 8070-T-MCU, 8070-OL-MCU, 8070-BL-MCU, 8070-OL-MCU-PCI
8070-LCD-10, 8070-LCD-15, LCD-15-SVGA
JOG PANEL, KEYBOARD PANEL, OP PANEL
BATTERY, MOUSE UNIT
Remote Modules RIOW, RIO5, RIO70
Note. Some additional characters may follow the model references indicated above. They all comply with the
directives listed here. However, compliance may be verified on the label of the unit itself.
Referred to by this declaration with following directives.
According to the European Community Directives 2006/95/EC on Low Voltage and 2004/108/EC
on Electromagnetic Compatibility and their updates.
In Mondragón, July 27th 2010.
Low-voltage regulations.
EN 60204-1: 2006 Electrical equipment on machines — Part1. General requirements
Regulation on electromagnetic compatibility.
EN 61131-2: 2007 PLC — Part2. Equipment requirements and tests

Hardware configuration
CNC 8070
(REF: 1007)
·11·
VERSION HISTORY
Here is a list of the features added to each manual reference.
Ref. 0601
Ref. 0609
Ref. 0705
Ref. 0706
Ref. 0710 / Ref. 0801
Ref. 0804
Ref. 0809
Ref. 0907
The PCI central unit is removed from the manual.
New monitor LCD-15".
The floppy disk unit with USB connectors is removed from the manual.
Remote modules (bus CAN with CANopen protocol).
ICU central unit.
MCU central unit.
15" passive screen.
Corrected the numbering of the pinout of "Phoenix Contact" connectors
The handwheel module with the E-stop button has been removed from the manual.
Corrected mouse dimensions.
The PC104 central unit is removed from the manual.
The VGA cable for passive screens is valid for cable carrying chains.
The remote modules with CANopen are now called RIOW5 remote modules.
The remote modules with CANfagor are now called RIOW70 remote modules.
New RIOW remote modules.
Corrected errors. Remote modules RIOW and RIO5 cannot handle a probe.
RS485 pinout correction.
Mechatrolink bus.
PCI expansion module for MCU central unit.

·12·
Hardware configuration
CNC 8070
(REF: 1007)
Ref. 1007
Corrected errors. Position of the dip-switches for selecting the speed in the CAN bus with CANopen protocol, in the
OP-PANEL-HE and Jog-Panel.
RIOW remote modules. The name of the RIOW-CANOPEN has been changed to RIOW-CANOPEN-ECO.
RIOW remote modules. New module RIOW-CANOPEN-STAND).
ICU - MCU central unit. Configure the serial line as RS232, RS422 or RS485.
RS485. At the line terminating resistor, pin 2 must NOT be jumpered with pins 7/9 nor pin 3 with pins 6/8
Thin Client

Hardware configuration
CNC 8070
(REF: 1007)
·13·
SAFETY CONDITIONS
Read the following safety measures in order to prevent harming people or damage to this product and those
products connected to it. Fagor Automation shall not be held responsible of any physical damage or
defective unit resulting from not complying with these basic safety regulations.
PRECAUTIONS BEFORE CLEANING THE UNIT
If the CNC does not turn on when actuating the start-up switch, verify the connections.
PRECAUTIONS DURING REPAIR
In case of a malfunction or failure, disconnect it and call the technical service.
PRECAUTIONS AGAINST PERSONAL DAMAGE
Before start-up, verify that the machine that integrates this CNC meets the 89/392/CEE Directive.
Do not get into the inside of the unit. Only personnel authorized by Fagor Automation may manipulate the
inside of this unit.
Do not handle the connectors with the unit
connected to AC power.
Before manipulating the connectors (inputs/outputs, feedback, etc.)
make sure that the unit is not connected to AC power.
Do not get into the inside of the unit. Only personnel authorized by Fagor Automation may manipulate the
inside of this unit.
Do not handle the connectors with the unit
connected to AC power.
Before manipulating the connectors (inputs/outputs, feedback, etc.)
make sure that the unit is not connected to AC power.
Interconnection of modules. Use the connection cables provided with the unit.
Use proper cables. To prevent risks, use the proper cables for mains, Sercos and Bus
CAN recommended for this unit.
In order to avoid electrical shock at the central unit, use the proper
power (mains) cable. Use 3-wire power cables (one for ground
connection).
Avoid electrical overloads. In order to avoid electrical discharges and fire hazards, do not apply
electrical voltage outside the range selected on the rear panel of the
central unit.
Ground connection. In order to avoid electrical discharges, connect the ground terminals
of all the modules to the main ground terminal. Before connecting the
inputs and outputs of this unit, make sure that all the grounding
connections are properly made.
In order to avoid electrical shock, before turning the unit on verify that
the ground connection is properly made.
Do not work in humid environments. In order to avoid electrical discharges, always work under 90% of
relative humidity (non-condensing) and 45 ºC (113 ºF).
Do not work in explosive environments. In order to avoid risks or damages, do no work in explosive
environments.

·14·
Hardware configuration
CNC 8070
(REF: 1007)
PRECAUTIONS AGAINST PRODUCT DAMAGE
PROTECTIONS OF THE UNIT ITSELF
Working environment. This unit is ready to be used in industrial environments complying with
the directives and regulations effective in the European Community.
Fagor Automation shall not be held responsible for any damage
suffered or caused by the CNC when installed in other environments
(residential or homes).
Install the unit in the right place. It is recommended, whenever possible, to install the CNC away from
coolants, chemical product, blows, etc. that could damage it.
This unit complies with the European directives on electromagnetic
compatibility. Nevertheless, it is recommended to keep it away from
sources of electromagnetic disturbance such as:
Powerful loads connected to the same AC power line as this
equipment.
Nearby portable transmitters (Radio-telephones, Ham radio
transmitters).
Nearby radio/TV transmitters.
Nearby arc welding machines.
Nearby High Voltage power lines.
Enclosures. The manufacturer is responsible of assuring that the enclosure
involving the equipment meets all the currently effective directives of
the European Community.
Avoid disturbances coming from the
machine.
The machine must have all the interference generating elements
(relay coils, contactors, motors, etc.) uncoupled.
Use the proper power supply. Use an external regulated 24 Vdc power supply for the keyboard and
the remote modules.
Grounding of the power supply. The zero volt point of the external power supply must be connected
to the main ground point of the machine.
Analog inputs and outputs connection. Use shielded cables connecting all their meshes to the corresponding
pin.
Ambient conditions. The storage temperature must be between +5 ºC and +45 ºC (41 ºF
and 113 ºF).
The storage temperature must be between -25 ºC and 70 ºC (-13 ºF
and 158 ºF).
Central unit enclosure. Make sure that the needed gap is kept between the central unit and
each wall of the enclosure.
Use a DC fan to improve enclosure ventilation.
Main AC power switch. This switch must be easy to access and at a distance between 0.7 and
1.7 m (2.3 and 5.6 ft) off the floor.
Remote modules. All the digital inputs and outputs have galvanic isolation via
optocouplers between the CNC circuitry and the outside.

Hardware configuration
CNC 8070
(REF: 1007)
·15·
SAFETY SYMBOLS
Symbols that may appear on the manual.
Symbols that the product may carry.
Danger or prohibition symbol.
It indicates actions or operations that may hurt people or damage products.
Warning symbol.
It indicates situations that certain operations could cause and the suggested actions to prevent them.
Obligation symbol.
It indicates actions and operations that must be carried out.
Information symbol.
It indicates notes, warnings and advises.
Ground protection symbol.
It indicates that that point must be under voltage.
i

Hardware configuration
CNC 8070
(REF: 1007)
·17·
WARRANTY TERMS
INITIAL WARRANTY
All products manufactured or marketed by FAGOR carry a 12-month warranty for the end user which could
be controlled by the our service network by means of the warranty control system established by FAGOR
for this purpose.
In order to prevent the possibility of having the time period from the time a product leaves our warehouse
until the end user actually receives it run against this 12-month warranty, FAGOR has set up a warranty
control system based on having the manufacturer or agent inform FAGOR of the destination, identification
and on-machine installation date, by filling out the document accompanying each FAGOR product in the
warranty envelope. This system, besides assuring a full year of warranty to the end user, enables our service
network to know about FAGOR equipment coming from other countries into their area of responsibility.
The warranty starting date will be the one appearing as the installation date on the above mentioned
document. FAGOR offers the manufacturer or agent 12 months to sell and install the product. This means
that the warranty starting date may be up to one year after the product has left our warehouse so long as
the warranty control sheet has been sent back to us. This translates into the extension of warranty period
to two years since the product left our warehouse. If this sheet has not been sent to us, the warranty period
ends 15 months from when the product left our warehouse.
This warranty covers all costs of material and labour involved in repairs at FAGOR carried out to correct
malfunctions in the equipment. FAGOR undertakes to repair or replace their products within the period from
the moment manufacture begins until 8 years after the date on which it disappears from the catalogue.
It is entirely up to FAGOR to determine whether the repair is or not under warranty.
EXCLUDING CLAUSES
Repairs will be carried out on our premises. Therefore, all expenses incurred as a result of trips made by
technical personnel to carry out equipment repairs, despite these being within the above-mentioned period
of warranty, are not covered by the warranty.
Said warranty will be applied whenever the equipment has been installed in accordance with instructions,
has not be mistreated, has not been damaged by accident or by negligence and has not been tampered
with by personnel not authorised by FAGOR. If, once servicing or repairs have been made, the cause of
the malfunction cannot be attributed to said elements, the customer is obliged to cover the expenses
incurred, in accordance with the tariffs in force.
Other warranties, implicit or explicit, are not covered and FAGOR AUTOMATION cannot be held responsible
for other damages which may occur.

·18·
Hardware configuration
CNC 8070
(REF: 1007)
WARRANTY ON REPAIRS
In a similar way to the initial warranty, FAGOR offers a warranty on standard repairs according to the
following conditions:
When the customer does not choose the standard repair and just the faulty material has been replaced,
the warranty will cover just the replaced parts or components within 12 months.
For sold parts the warranty is 12 moths length.
SERVICE CONTRACTS
The SERVICE CONTRACT is available for the distributor or manufacturer who buys and installs our CNC
systems.
PERIOD 12 months.
CONCEPT Covers parts and labor for repairs (or replacements) at the
network's own facilities.
EXCLUDING CLAUSES The same as those applied regarding the chapter on initial
warranty. If the repair is carried out within the warranty period, the
warranty extension has no effect.

Hardware configuration
CNC 8070
(REF: 1007)
·19·
MATERIAL RETURNING TERMS
When sending the central nit or the remote modules, pack them in its original package and packaging
material. If the original packaging material is not available, pack it as follows:
1Get a cardboard box whose three inside dimensions are at least 15 cm (6 inches) larger than those
of the unit. The cardboard being used to make the box must have a resistance of 170 Kg (375 lb.).
2Attach a label indicating the owner of the unit, person to contact, type of unit and serial number. In case
of malfunction also indicate symptom and a brief description of the problem.
3Wrap the unit in a polyethylene roll or similar material to protect it. When sending a central unit with
monitor, protect especially the screen.
4Pad the unit inside the cardboard box with poly-utherane foam on all sides.
5Seal the cardboard box with packing tape or industrial staples.