F&F DR-09-IP65 User manual

- 1 -
DR-09-IP65
Hermetic motion sensor (PIR),
with presence sensor function
The motion sensor is used for automatic and temporary swit-
ching on of lighting if a person or other object appears in places
such as hallways, courtyards, driveways, garages, etc.
It is suitable for use in narrow corridors.
The sensor detects the infrared radiation sources. It analyzes
the parameters such as the size of the object, the amount of
heat emitted and the speed of movement between sectors of
detection. The sensor detects movement within its own axis and
radius. Movement in the detection area will automatically swi-
tch on the lighting. From this moment the light will stay on, as
long as the sensor detects continuous movement. Only if there is
no movement in the detection area triggers the lighting support
time. Another movement in the detection area and its subsequ-
ent disappearance in the course of time measurement starts the
support time from the beginning.
Purpose
Functioning
F&F Filipowski sp. j.
Konstantynowska 79/81, 95-200 Pabianice, POLAND
phone/fax [phone]
www.fif.com.pl; e-mail: [e-mail]
Do not dispose of this device in the trash along with other waste!
According to the Law on Waste, electro coming from households free of charge and can
give any amount to up to that end point of collec� on, as well as to store the occasion of
the purchase of new equipment (in accordance with the principle of old-for-new, regard-
less of brand). Electro thrown in the trash or abandoned in nature, pose a threat to the
environment and human health.

- 2 -
The specific of operation allows using the DR-09-IP65 as a pre-
sence sensor. The area of the detection field is: for presence up
to 6 m in diameter and for movement up to 20 m in diameter.
The motion sensor is equipped with a twilight sensor to prevent
switching on the lighting during the day. The detection status
and the readiness to switch on the lighting are only activated
after dusk. The activation time of the sensor can be adjusted
by the user using a potentiometer. In addition, it is possible to
adjust the time of sensor switching on within the range of 3 s÷9
min.
Changes in temperature can affect the motion detec-
tion.
The minimum distance between the sensor and the li-
ght source is 60 cm. If the motion sensor is installed too
close to the switched light source, the system may be
activated, which means that the sensor will automa-ti-
cally switch on and off the light source. It is necessary to
move the sensor to an appropriate distance away from
the light source.
Diagram

- 3 -
Switch-on time
The time of the receiver switching on can
be adjus-ted within the range of 3 sec to
9 min. Turning the control knob right [+]
increases the switching on time, turning
left [–] reduces the switching on time.
The sensitivity of the twilight sensor
The sensitivity of the twilight sensor can be
adjusted within the range of 3 lx to 2000 lx.
Turning the control knob in the direction of
the "moon" icon will switch the light later,
turning it in the direction of the "sun" –
will switch the light earlier. For the sensor
to be active throughout the whole day, the
control knob should be maximally turned
in the direction of the "sun".
Sensor installation height (adjustable range of sensor detection)
Settings
Detection area

- 4 -
The direction of movement in the detection area
Dimensions

- 5 -
1.Remove the external sensor cover - squeeze the housing from
both sides with your hand and gently pull it out of the internal
housing.
2.Disconnect the power supply.
3.Connect the wires according to the wiring diagram.
4.Fasten the base to the floor with two screws.
5.Set the sensitivity of the twilight sensor and activation time.
6.Assemble the sensor housing – press it onto internal housing.
7.Switch on the sensor power supply.
If the motion sensor is installed too close to the switched
light source, the system may be activated, which means
that the sensor will automatically switch on and off the
light source. It is necessary to move the sensor to an ap-
propriate distance away from the light source.
The sensor is inactive for the first 30 seconds after the
power supply is switched on. During this time, the PIR
system warms up.
The motion sensor can work indoors and outdoors in
places where it is not exposed to direct rain or snowfall
and to the possibility of splashing the sensor housing
and its electrical connection points with water or other
liquid.
Mounting

- 6 -
Avoid locations with large objects in the detection area
such as trees that can be moved by the wind.
Do not install the sensor in the immediate vicinity of he-
ating, air-conditioning and lighting devices.
Wiring diagram

- 7 -
power supply 195÷265 V AC
maximum load current (AC-1) 10 A
twilight activation threshold 3÷2000 lx
motion detection 0.6÷1.5 m/s
switch-off time 3 s÷9 min. (±2min.)
horizontal detection area 360°
max radius of detection (T<24°C) 10 m
sensor mounting height 2.2÷6 m
power consumption
standby 0.10 W
on 0.45 W
terminal 1.5 mm² screw terminals
tightening torque 0.3 Nm
working temperature -20÷40°C
dimensions 102×102 mm, h= 55 mm
mounting surface
ingress protection IP65
Technical data

- 8 -
tungsten halogen fluorescent energy-saving LED
2000 W 2000 W 300 W 300 W 300 W
The above data are indicative and will heavily depend on the
design of a specific receiver (that is especially important for
LED bulbs, energy-saving lamps, electronic transformers and
pulse power supply units), switching frequency and operating
conditions.
For more information visit: www.fif.com.pl.
The F&F products are covered by a warranty of the 24 months
from the date of purchase. Effective only with proof of purchase.
Contact your dealer or directly with us.
F&F Filipowski sp. j. declares that the device is in conformity
with the essential requirements of The Low Voltage Directive
(LVD) 2014/35/EU and the Electromagnetic Compatibility (EMC)
Directive 2014/30/UE.
The CE Declaration of Conformity, along with the references to
the standards in relation to which conformity is declared, can be
found at www.fif.com.pl on the product page.
Power table
Warranty
CE declaration
E210827