F&F DRM-02 User manual

- 1 -
DRM-02
Microwave motion sensor,
with presence detector
The motion sensor is used for automatic and temporary swit-
ching on of lighting if a person or other object appears in places
such as hallways, courtyards, driveways, garages, etc.
The sensor can detect movement through wooden, plasterbo-
ard, glass and plastic panels.
The DRM microwave sensor operates as a radar by using high
frequency electromagnetic waves to detect movement in a mo-
nitored area. It is most effective when the movement takes place
directly towards the sensor. In addition, the DRM has a built-in
twilight switch that prevents the controlled lighting from swit-
ching on during the day. When motion is detected after dusk,
the lighting will be switched on and will remain on as long as
motion is detected. When the movement stops, the light rema-
ins switched on for a specified back-up time, after which it is
switched off.
Purpose
Functioning
F&F Filipowski L.P.
Konstantynowska 79/81, 95-200 Pabianice, POLAND
phone/fax [phone]
www.fif.com.pl; e-mail: [e-mail]
Do not dispose of this device in the trash along with other waste!
According to the Law on Waste, electro coming from households free of charge and can
give any amount to up to that end point of collec� on, as well as to store the occasion of
the purchase of new equipment (in accordance with the principle of old-for-new, regard-
less of brand). Electro thrown in the trash or abandoned in nature, pose a threat to the
environment and human health.

- 2 -
If motion is detected again during the back-up time, the cycle
will start from the beginning. Due to its high sensitivity, the
DRM can act as a presence sensor. The accuracy of the sensor
operation does not depend on the temperature. The detection
range, the brightness level that activates the sensor and the time
of operation back-up are set using the knobs described later in
this manual. The sensor is designed for indoor use.
The power of microwave radiation is relatively low and
completely safe for humans and animals. Its value is
below 10 mW. In comparison, a microwave oven and a
mobile phone radiate with a power of approx. 1000 mW.
Diagram

- 3 -
Twilight switch sensitivity (LUX)
Sensitivity of the twilight switch can be
adjusted in the range of 2÷2000 lx. Turning
the knob towards the "moon" will switch
the lighting on later, turning the knob
towards the "sun" will switch it on earlier.
To keep the sensor active throughout the
whole day, turn the knob as far as possible
towards the "sun".
Detection area (SENS)
The detection radius of the sensor can be
adjusted from 1 m to 10 m (parameters
given for a sensor mounted at a height
of 2.5 m).
Turning the knob clockwise [max] increases
the detection area, turning it countercloc-
kwise [min] decreases the detection area.
Switch-on time (TIME)
The switch-on time of the receiver can be
adjusted in the range from 5 s to 12 min.
Turning the knob clockwise [max] increases
the switch-on time, turning it countercloc-
kwise [min] decreases the switch-on time.
Settings

- 4 -
1.Unscrew the external sensor cover. Unscrew the 2 screws and
remove the sensor cover (Fig. 1).
2.Disconnect the power supply.
3.Pass the wires through the rubber grommet in the sensor mo-
unting base.
4.Fasten the base with 2 screws to the ground (Fig. 2).
5.Connect according to the diagram.
6.Set the area of the detection field, the sensitivity of the twili-
ght automatic system and the switching time.
7.Assemble the sensor casing (Fig. 3).
When the power is switched on, the motion detector is
inactive for the first 10 seconds.
Mounting

- 5 -
3-terminal connection
4-terminal connection
Wiring diagram

- 6 -
power supply 195÷265 V AC
maximum load current (AC-1) 5 A
frequency of microwaves radiation 5.8 GHz
radiation power 10 mW
detection field 360°
detection radius (adjustable)
for h= 2.5 m 1÷10 m
activation threshold (adjustable) 2÷2000 lx
switching time (adjustable) 5 s÷12 min.
activation delay 1 s
power consumption 0.9 W
terminal 1.0 mm² screw terminals
tightening torque 0.25 Nm
working temperature -25÷50°C
dimensions ø103, h= 44 mm
mounting surface
mounting height 2÷6 m
ingress protection IP20
tungsten halogen fluorescent energy-saving LED
1000 W 700 W 100 W 100 W 100 W
Technical data
Power table

- 7 -
The above data are indicative and will heavily depend on the
design of a specific receiver (that is especially important for
LED bulbs, energy-saving lamps, electronic transformers and
pulse power supply units), switching frequency and operating
conditions.
For more information visit: www.fif.com.pl.
The F&F products are covered by a warranty of the 24 months
from the date of purchase. Effective only with proof of purchase.
Contact your dealer or directly with us.
F&F Filipowski L.P. declares that the device is in conformity with
the essential requirements of The Directive 2014/53/EU of the
European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the
making available on the market of radio equipment and repe-
aling Directive 1999/5/EC.
The CE Declaration of Conformity, along with the references to
the standards in relation to which conformity is declared, can be
found at www.fif.com.pl on the product page.
PN-EN 62368-1:2015-03
PN-EN 62479:2011
PN-ETSI EN 301 489-1 V2.1.1:2017-08
PN-ETSI EN 300 489-3 V1.6.1:2014-03
PN-ETSI EN 300 440-2 v.2.1.1: 2017-10
Warranty
CE declaration
Compliance with standards
E230310