F&F DRM-08 5 9 0 8 3 1 2 5 9 9 8 8 3 Functioning TIME 12min. 10s 6min. 3min. 30s 90s LUX 3 300 30 SENS + - F&F Filipowski sp. j.... User manual

- 3 - - 4 -
- 1 - - 2 -
Assembly
1. Twist the sensor outer casing off by hand.
2. Disconnect the power supply.
3. Put the wires through the rubber cable bush in chassis of the sensor.
4. Fix the base to the ground.
5. Connect according to the diagram.
WARNING!
DRM is inactive for the first 10 seconds after powering up.
6. Set the detection area, sensitivity of the twilight switch and the switch-
on time.
7. Assemble the outer casing of the sensor.
Purpose
The motion sensor is designed for automatic, scheduled lighting activation if
a person or other object appears in places such as corridors, courtyards,
approaches and driveways, garages, etc.
The specific of operation allows to use the DRM-08 as a presence sensor.
The sensor allows to detect movement through wooden boards, plaster-
board panels, glass and plastics.
The DRM sensor emits and receives 5.8 GHz high frequency electromagnetic
waves. The sensor detects changes in wave reflection caused by the
movement of the object in the detection area. The sensor detects movement
of the object to and from the sensor. Movement in the detection area
automatically switches on the lighting. From the moment of switching on,
continuous movement causes the lighting to stay on permanently. Only lack
of movement in the detection area triggers the lighting back-up time.
Another movement in the detection area and its disappearance during the
countdown will start the back-up time from the beginning. The nature of the
operation allows the DRM to be used as presence sensor.
After the preset time, the lighting will be switched off automatically. The
motion sensor is equipped with a twilight sensor that prevents the
controlled lighting from being switched on during the day. The detection
status and the readiness to switch on the lights are activated only after dark.
Activation time of the sensor can be adjusted by the user through a
potentiometer. In addition, it is possible to adjust the detection area in the
radius range of 1÷8 m (for h=2÷6 m) and to adjust the time of the receiver in
the range of 10sec÷12min. The motion sensor can work indoors. The sensor
allows to detect movement through wooden boards, plasterboard panels,
glass and plastics. Temperature changes do not affect motion detection.
WARNING!
The power of microwave radiation is relatively low and is completely safe for
humans and animals. Its value is less than 0.2 mW.
By comparison, microwaves and cell phones radiate about 1000mW of
power (100 times harder).
Actuation time (TIME)
Receiver’s actuation time can be adjusted between 8 sec
for 12 min. Rotate knob to the right increases ON time,
rotate left reduces the attached time.
Detection range (SENS)
Radius of the sensor detection can be adjusted in the range
from 1 m to 8 m (the parameters for the sensor mounted at
a height 1÷6 m). Rotate the knob to the right [+] increases
the area of a field of detection, rotate left [−] reduces the
area of the field detection.
Sensitivity of light dependant relay (LUX)
Sensitivity of light dependant relay can be adjusted in range
from 3Lx to 2000Lx. Rotate the knob to „3” - attached later;
rotation to the „sun” sign - attached earlier.
In order to sensor was active throughout the day, set the
knob maximally toward the „sun”.
Settings
Diagram
tOFF tOFF<tOFF
MICROWAVE
MOTION SENSOR DRM-08
5 9 0 8 3 1 2 5 9 9 8 8 3
Functioning
TIME
12min. 10s
6min.
3min.
30s
90s
LUX
3
300 30
SENS
-
+
F&F Filipowski sp. j.
Konstantynowska 79/81 95-200 Pabianice
phone/fax: [phone] POLAND
http://www.fif.com.pl e-mail: biur[email protected]
WARRANTY. The F&F products are
covered by a warranty of the 24 months
from the date of purchase. Effective only
with proof of purchase. Contact your
dealer or directly with us. More informa-
tion how to make a compliant can be
found on the website:
www.fif.com.pl/reklamacje
Do not dispose of this device in the trash along with other waste! According
to the Law on Waste, electro coming from households free of charge and can
give any amount to up to that end point of collection, as well as to store the
occasion of the purchase of new equipment (in accordance with the principle
of old-for-new, regardless of brand). Electro thrown in the trash or abandoned
in nature, pose a threat to the environment and human health.

- 5 - - 6 -
D161020
Wiring diagram Technical data
power supply 230V AC
current load <10A
microwave radiation frequency 5.8GHz
power radiation <10mW
motion detection 0.6÷1.5m/sec
detection area 360°
detection radius - adjustable (for h=1÷6m) 1÷8m
activation threshold - adjustable 3÷2000Lx
switch-on time of receiver - adjustable 10±3sec÷12±1min
activation delay <1sec
power consumption 0.9W
terminal 1mm² screw terminals
working temperature -25÷50°C
dimensions Ø115 h=24mm
mounting two screws to substrate
protection level IP20
2000W 300W
2000W
incandescent fluorescent energy-saving
halogen LED
300W 300W
Table of power
N
L
N
LNL’
IN ~