F&F LE-03d User manual

- 1 -
LE-03d
Electric energy meter,
3-phase
Directive MID 2014/32/EU
Certificate number 0120/SGS0119
The LE-03d is a static (electronic) calibrated electricity meter of
three-phase alternating current in a semidirect system.
A special electronic system under the influence of flowing cu-
rrent and applied voltage in each phase generates pulses pro-
portional to the energy drawn in the respective phase. Energy
consumption in the phase is indicated by a flashing of correspon-
ding LED (A, B, C). The sum of the three phase pulses is indicated
by a flashing LED and converted into energy absorbed througho-
ut the three-phase system. Its value is displayed by the segment
LCD display.
The fractional digit represent the decimal (.1 kWh = 100 Wh).
Compliance
Purpose
Functioning
F&F Filipowski sp. j.
Konstantynowska 79/81, 95-200 Pabianice, POLAND
phone/fax [phone]
www.fif.com.pl; e-mail: [e-mail]
Do not dispose of this device in the trash along with other waste!
According to the Law on Waste, electro coming from households free of charge and can
give any amount to up to that end point of collec� on, as well as to store the occasion of
the purchase of new equipment (in accordance with the principle of old-for-new, regard-
less of brand). Electro thrown in the trash or abandoned in nature, pose a threat to the
environment and human health.

- 2 -
Active energy consumed AE+ [kWh]
The indicator has a pulse output. This allows you to connect a
pulse meter-reading pulses generated by the counter. For proper
operation of the indicator is not required to connect additional
devices.
The meter has sealable input and output terminal covers to pre-
vent any attempts to bypass the meter.
Measured value
Pulse output
Sealing

- 3 -
The meter is marked with individual serial number allowing its
unambiguous identification. The marking is laser engraved and
cannot be removed).
Meter number
Front description

- 4 -
1.Disconnect the power supply.
2.The indicator mounted on a rail in the distribution box.
3.Connect the power in accordance with the markings to the
terminals 1 (L1), 3 (L2), 5 (L3).
4.Connect the measured circuit or a single receiver to the termi-
nals in accordance with the markings to the terminals 2 (L1),
4 (L2), 6 (L3).
5.N-wire connect to terminal 7.
6.Additional pulse receiver connected (optional) to terminals
9(+) and 8(–).
Additional pulse receiver is not required.
7.Put the meter terminals covers.
Dimensions
Mounting

- 5 -
1 power input L1IN
2 power output L1OUT
3 power input L2IN
4 power output L2OUT
5 power input L3IN
6 power output L3OUT
7 neutral N-wire
8 pulse output (–)
9 pulse output (+)
Wiring diagram

- 6 -
installation 4-wire
rated voltage 3×230/400 V
minimum measured current 0.04 A
base current 3×10 A
maximum current 3×100 A
voltage measuring range 160÷265 V
measurement accuracy (EN50470-1/3) B class
rated frequency 50 Hz
insulation protection class II
housing PC+ABS material
own power consumption <10 VA; <0.2 W
indication range 0÷999999.9 kWh
constant 1000 pulses/kWh
current consumption signalling A, B, C phases 3× red LED
read-out signalling red LED
pulse output
type open collector
maximum voltage 27 V DC
maximum current 27 mA
pulse time 35÷80 ms*
working temperature -20÷55°C
terminal 25 mm² screw terminals
dimensions 7 modules (122 mm)
mounting on TH-35 rail
ingress protection IP20
__________
* depends on the current consumption
Technical data

- 7 -
F&F products are covered by a 24-month warranty from the date
of purchase. The warranty is only valid with proof of purchase.
Contact your dealer or contact us directly.
F&F Filipowski sp. j. declares that the device is in conformity
with the essential requirements of The Low Voltage Directive
(LVD) 2014/35/EU and the Electromagnetic Compatibility (EMC)
Directive 2014/30/UE.
The CE and MID Declaration of Conformity, along with the refe-
rences to the standards in relation to which conformity is decla-
red, can be found www.fif.com.pl on the product subpage.
Warranty
CE declaration

- 8 -E210430
»Please read the instructions carefully before installation.
»The device should be installed and operated by qualified per-
sonnel who are familiar with its design, operation, and asso-
ciated risks.
»Do not install a meter that is damaged or incomplete.
»The user is responsible for proper grounding of the system,
proper selection, installation, and efficiency of other devices
connected to the meter, including safety devices such as over-
current, residual current and overvoltage circuit breakers.
»Before connecting the power supply, make sure that all cables
are connected correctly.
»It is essential to observe the operating conditions of the meter
(supply voltage, humidity, temperature).
»To avoid electric shock or damage to the meter, turn off the
power supply whenever the connection is changed.
»Do not make any changes to the unit yourself. Doing so can
result in damage to or improper operation of the device,
which in turn can pose a threat to people operating it. In such
cases, the manufacturer is not responsible for the resulting
events and may refuse the provided warranty in the event of
a complaint.
»Do not tighten the terminals without the wire inserted. This
may damage the lift mechanism of the terminal or the plastic
cover of this terminal.
General work safety conditions