Fanvil X301W User manual

Quick Installation Guide
Fanvil Technology Co., Ltd
www.fanvil.com
X301W
V1.0
- 4 -
Call forward
1. Press Menu > Features > Call Forward.
2. Select the line, the type of forward, enter the destination
number and status, and press OK soft key.
Call conference
Call transfer
Attended transfer:
Blind transfer:
Regulatory Compliance
Federal Communication Commission (FCC) — USA
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received; including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed
and used in accordance with the instruction manual, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other
information, a product identifier in the format US: 3I1IPNANX303W. If requested, this number must be provided to the telephone company.
Fanvil Technology Co., Ltd
Website: www.fanvil.com
EMail: [email protected] [email protected]
Tel: [phone] Fax: [phone]
Add: 10/F Block A, Dualshine Global Science Innovation Center,
Honglang North 2nd Road, Bao'an District, Shenzhen, China
1. Press the Conference soft key during an active call.
The call is put on hold.
2. Call the second party's number.
3. After 2nd call is established, press the Conference soft key
to let all parties joined in the conference.
1. Press key or Xfer soft key during the active conversation,
the call will be on hold.
2. Then enter the 2nd telephone number and press key
or Xfer soft key.
1. Press key or Xfer soft key during the active conversation,
the call is put on hold.
2. Dial the second telephone number.
3. When the call is answered, then press key or Xfer soft
key to complete the operation.
Do not disturb
Voice mail
1. To access your voice mailbox, press or Menu
> Message > Voice Message, number of messages will be
indicated if provided by your server or pbx.
2. Select the line and press Play to call.
Phonebook
Access phonebook:
Add new entry:
1.Press Dir soft key or Menu > Contact > Local Contacts.
2.Select All Contacts
3. To dial an entry, press Dial soft key or pickup handset or
press or .
1. Press DND soft key, or Menu > Features > DND.
2. Select the Mode and Type, and press Save soft key.
1. Press Dir soft key > Local Contacts > Press Add.
2. Enter name and number and press OK soft key.
Call list
1. Press key or Menu > CallLog > Local Call Logs.
2. Scroll through the list using .
3. Todial an entry, press Dial soft key or pickup handset or
press or .
Redial
1. Press key, redial a call number.
Call Mute
1. Press to Mute the microphone during the call.
2. Press again to un-mute the conversation.
Putting a call on hold
1. Press key or Hold soft key, caller is put on hold.
2. Toretrieve the call press key or Resume soft key.
Note: with more than one active call, select desired call with
the navigator keys and use the corresponding soft key to
hold or resume.

Packaging list
IP Phone Handset
Handset Cord
Stand Power Adapter
(Optional)
Ethernet Cable Quick Installation Guide
- 3 -
Wall Stand
(Buy separately)
Device Installation
Wall mounting (Wall Stand need buy separately)
Screen icon
Connecting to the Device
Please connect power adapter, network, handset, and
headset to the corresponding ports as described in below
picture.
Note: The installation height of the wall-mounted
bracket is less than 2 meters from the ground.
①Power port: connect the power adapter.
②Network port: connecting local area network or Internet.
③PC port: the network port connect to the computer.
④Headset port: connect headset.
⑤Handset port: connect IP Phone handset.
Internet DC 5VPC Headset Handset
⑤④
③ ① ②
Please follow the instructions in below picture to install the
device.
Bracket desktop installation
Language setting
1. Press Menu key > Basic > Language.
2. Select the desired language and press OK soft key.
Making a call
Accepting a call
1. Pre-dialing:enter the phone number and pick up the handset.
2. Direct dialing:lift the handset and enter the phone number.
3. Handsfree :enter phone number and press or vice versa.
4. Headset:enter phone number and press or vice versa.
1. Using the handset:pick up the handset.
2. Using the headset:press .
3. Using the handsfree :press .
Configuration via Web
1. Get the IP address from the phone: Press key, or Menu
> Status > ETH.
2. Login: Input the IP address in the web browser. The PC and
phone should be in the same IP address segment(The default
username and password are both ‘admin’.)
3. Configure: Select network/Account etc, and fill the relevant
content.
4. Save the configuration.
Configuration
Configuration via Phone
1. Press Menu > System (Default password123).
2. Select Network: To configure the Network Settings
( IPv4/ IPv6/ IPv4 & IPv6 ).
3. Select Accounts: To configure enable the account, fill the
SIP server address, port, user name, password etc.
- 2 -
In hands-free mode
In headset mode
In handset mode
Mute activated
Ring off
Call is on hold
Auto-answering activated
Internet is
disconnected
Keypad locked
New VM Messages
Call Forward activated
Do Not Disturb activated
Missed call(s)
Received call
Dialed call
Wireless network
connected
Wireless network
disconnected
Wireless network failure
5. Designated line :press line key, enter phone number and
press dial key.
Network connect
Using Ethernet
1. The power on the device and connect the WAN port of the
phone to the RJ45 socket of a hub/switch or arouter
(LAN side of the router) using the Ethernet cable.
2. The default is DHCP mode.
Using WiFi
1. The power on the device and make sure the phone is idle.
2. Press Menu > Basic > WLAN, Enabled the WiFi Feature.
3. Press scan to search for currently available wireless network.
4. Enter the available network and select the WiFi you want to
connect.
5. Press connect soft key and enter the appropriate password to
connect to the WiFi. The default is DHCP mode.
Key features
In idle mode:
activate/deactivate silent mode
In communication mode:
mute/un-mute a call
In idle mode or during ringing:
increase or decrease ringer volume
In communication:
increase or decrease handset,
headset or hands-free volume
Long press to lock keypad.
Enter PIN to unlock keypad (default 123)
Voice messages key
Conference key
State key
Headset key, Activate/
deactivate headset
Redial key, Access to
redial the last record
Hands-free key, Activate/
deactivate hands free
Phonebook key
Message waiting indicator
Left and right navigation keys
Up navigation key, Shortcut to call log
Down navigation key, Shortcut to Status
OK key, Shortcut to Menu
Call transfer key
Hold key, Hold/Resume the call
Soft keys